viessmann TT 6923 Whip-Type Lamp Post Double Assembly Kit User Manual

: June 12, 2024
: VIESSMANN

Table of Contents

viessmann TT 6923 Whip-Type Lamp Post Double Assembly Kit
Important information
- Safety instructions
Introduction
Assembly
Mounting
Connection
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

viessmann TT 6923 Whip-Type Lamp Post Double Assembly Kit

viessmann-TT-6923-Whip-Type-Lamp-Post-Double-Assembly-Kit-
PRODUCT

Model building item, not a toy! Not suitable for children under the age of 14 years! Keep these instructions

Important information

Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution:
Risk of injury! Due to the detailed reproduction of the original and the intended use, this product can have peaks, edges and breakable parts. Tools are required for installation.

Electrical hazard!

Never put the connecting wires into a power socket!
Regularly examine the transformer for damage. In case of any damage, do not use the transformer!
Make sure that the power supply is switched off when you mount the device and connect the cables!
Only use VDE/EN tested special model train transformers for the power supply!
The power sources must be protected to prevent the risk of burning cables.

Using the product for its correct purpose
This product is intended:

For installation in model train layouts and dioramas.
For connection to an authorized model train transformer (e. g. item 5200).
For operation in dry rooms only.

Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.

Checking the package contents
Check the contents of the package for completeness:

2 LEDs with connection cables
2 heat shrink tubes
2 lamp shades
2 lamp glasses
Lamp mast
Base socket
Resistor (multi-coloured rings)
Diode (single ring)
Manual

Introduction

This lamp produces light by SMD-LEDs which is suitable to the lamp model. Low heat build-up and power input. Nearly unlimited lifetime of the LEDs, so no more change is required

Assembly

Remove the lamp kit carefully from the package

viessmann-TT-6923-Whip-Type-Lamp-Post-Double-Assembly-Kit-
FIG-3

Slide the two cable ends of the LEDs through the lamp mast (fig. 3 steps 1 and 2).
Slide the base socket onto the cables (fig. 3 step 3).
Slide the lamp shade over the LEDs to the lamp mast (fig. 3 steps 4 and 5). Afterwards the LED is placed in the lamp shade.
Put the lamp glass onto the lamp shade (fig. 3 steps 6 and 7).
Strip the yellow cable to ca. 2 cm. Bend the blank wire (ca. 1 cm) by 180° until it touches itself. Insert the wire bottom-up through the lamp mast (fig. 4). The brass mast serves as a second conductor. Twist the brown and the yellow wires below the mast.
Slide the yellow heat shrink piece onto both yellow cables and the black heat shrink piece onto the brown cable (fig. 3 step 9).
Bend the short wire end of the resistor and the diode in the middle by 90°. Wind the blank cable ends of the yellow cables around the wire directly below the resistor and the end of the brown cable around the wire directly below the diode.
Afterwards bend the vertical end of the resistor and the diode.
Slide the heat shrink tube onto the previously made contact point (cable + resistor or diode).
Heat it briefly (!), e. g. with a hot air gun and a durable connection has been accomplished! Attention: Risk of burn

Mounting

Check function before mounting.
Drill a hole (Ø 3.5 mm) at the mounting place (fig. 1).
Put the base socket with the cables from above through the hole

When connecting the cables, please leave a loop of ca. 2 – 3 cm behind the lamp, which enables you to pull the lamp out of the assembly drilling.

Caution:
Resistor and diode at the cables are needed for proper function of the lamp. Never cover resistor or diode with insulation material, because they have to be cooled by surrounding air

Connection

Connect the LED lamp to the light output of a model train transformer (e. g. item 5200) as shown in fig. 4 and/or 5.

DC voltage: Connect the diode with the positive pole and the resistor with the negative pole of the power supply.

AC voltage : Operation with AC voltage could cause some flickering.We recommend to use the Viessmann power module, item 5215 (fig. 5) which is sufficient for ca. 100 LED lamps or reflectors. Connect the cable with the diode to the brown output socket and the cable with the resistor to the red output socket (fig. 4).

Technical data

Operating voltage : 10 – 16 V AC ~ (with and without item 5215 power module) 14 – 24 V DC = 13 – 24 V digital signal
Operating current : ca. 10 mA

DISPOSAL
Do not dispose of this product through (unsorted) domestic waste, supply it to recycling instead Subject to change without prior notice. No liability for mistakes and printing errors. You will find the latest version of the manual on the Viessmann website using the item number

Viessmann Modelltechnik GmbH Bahnhofstraße 2a D – 35116 Hatzfeld-Reddighausen