HAVIT HV2892-SS316 Mini Ollo Installation Guide
- June 1, 2024
- havit
Mini Ollo Inground or Deck Light Installation Instructions
Product Specifications
Model No.| HV2892W-SS316| HV2892C-SS316 | HV2892W-BLK| HV2892C-BLK| HV2892W-
CP| HV2892C-CP
---|---|---|---|---|---|---
Name| Mini Ollo
Material| 316 Stainless Steel| 316 Stainless Steel| 316 Stainless Steel +
Copper
Colour| Stainless Steel| Black Cover with Stainless Steel body| Copper Cover
with Stainless Steel body
IP Rating| IP67
Input Voltage| 12v DC
Lamp Base| Built in LED
Lamp Wattage| 1x 1w
Colour Temp| 3000k| 5500k| 3000k| 5500k| 3000k| 5500k
Lumens| 80lm| 90lm| 80lm| 90lm| 80lm| 90lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
Adequate Drainage
Slight decline on Ground level to allow for water to run away from fitting
100mm – 150mm of Crushed Rock
- Light Fitting
- Canister
- 100mm Space
Dimensions
Cutout with Canister Cutout without Canister
Sample Wiring Diagram
- 12v DC LED Driver
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where fitting is to be placed using dimensions provided on line drawings,
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- If installing into concrete, insert canister making sure it is flush with wall.
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Insert fitting into hole or canister
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions***
Documents / Resources
|
HAVIT HV2892-SS316 Mini
Ollo
[pdf] Installation Guide
HV2892-SS316, HV2892W-SS316, HV2892C-SS316, HV2892W-BLK, HV2892C-BLK, HV2892W-
CP, HV2892C-CP
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>