edbak WWTR-TR5E Versatile Video Conferencing Cart Trolley for 42-65 Inch Screen Instruction Manual

edbak WWTR-TR5E Versatile Video Conferencing Cart Trolley for 42-65 Inch

Screen

Warning Please read this manual before starting the installation to ensure correct assembly. The assembly should be carried out in accordance with this manual by at least two fully qualified people. The EDBAK Company shall not be liable for any injuries or damage to material or property caused by incorrect assembly. Hence please ensure that:

• during the assembly all the instructions are followed carefully. Failure to do so may result in damage to the product or property, or even personal injury;
• before assembly you must ensure that there are no power cables, or water, sewage or gas pipes in the area of the ceiling where the mount is to be fixed;
• extra caution should be taken with movable parts in order to avoid crushing or pinching your hands or fingers. The movable parts are identified in this manual. This equipment may be used by children aged 8 years and over and by persons with reduced physical and mental capabilities and lack of experience and knowledge of the equipment if supervision or instruction is provided on how to use the equipment in a safe way so that the associated risks are understood. Children should not play with the equipment. Children without supervision should not perform cleaning and maintenance of the equipment.

DEVICE CONSTRUCTION

TROLLEY’S DIMENSIONS

UNBOXING

Upon delivery, check the contents of the package:

• that the delivered device arrived undamaged, with no visible dents or scratches.
• Does the package contain a full set to assemble the AV cart:
  • two legs
  • leg connector
  • four wheels with brakes
  • two tubes
  • mounting plate
  • plate clamp
  • two arms
  • two halves of the rosette
  • a set of screws and wrenches

MOUNTING THE WHEELS TO THE LEGS

ASSEMBLY

BASE ASSEMBLY

Using eight M8x16 bolts, M8 spring washers, M8 round washers and a 6mm Allen key, connect both legs with the Leg Connector.

BOTTOM TUBE ASSEMBLY

Insert the longer tube inside the Leg connector, and then screw it with an 8mm Allen key, using two M10x30 screws, two M10 spring washers and two M10 round washers.

TOP TUBE ASSEMBLY

Put the trolley on the wheels. Slide the shorter tube over the narrowing of the lower tube, making sure that the holes made in both elements coincide. After inserting the tubes, they should be screwed together with a M6x10 conical screw, using a 4mm Allen key. Insert a fi60 plastic cap into the upper part of the tube.

MAIN PLATE ASSEMBLY

Attach the plate on which the monitor will hang to the pole with a clamp. Screw the clamp with the plate using four M8x16 screws, spring washers and M8 round washers. The screws should be tightened securely and firmly so that the plate does not slide down due to the weight of the monitor. After clamping the plate on the pole, put four plastic masking caps on the screw heads.

ROSETTE ASSEMBLY

In order to stiffen the column, screw two “moon-shaped” rosettes to the leg connector using four M16x16 conical screws and a 4mm Allen wrench.

ARMING THE MONITOR

Using the included screws and washers, screw the arms to the VESA holes on the TV. If the length of the screws turns out to be too long, plastic spacers should be used.

MONITOR HANGING

Apply the brakes on all wheels before suspending the monitor on the plate. Then, on the hooks made in the arms, attach the monitor to the motherboard. Make sure the monitor hangs securely from all hooks.

LOCKING THE ARMS ON THE MAIN BOARD

In order to protect the monitor against accidental sliding off the plate, two M6 screws located in the lower part of the arms should be tightened to the plate.

CONNECTION OF POWER AND SIGNAL CABLES

Lead the power and signal wires inside the pole and connect to the monitor. Pay attention to disconnecting all power cords when moving the trolley.

FINAL REMARKS

• Purpose of the device: mobile holder for monitors weighing not more than 50 kg, sizes in the range of 42-60 “, and VESA holes in the range of 100×100 – 600×400.
• The maximum height of the center of the monitor must not exceed 1685mm.
• Application of the device: indoors
• Be especially careful when moving the device:
  • the trolley should be moved slowly, taking care not to hit the wheel on the foot or other delicate objects
  • pay attention not to catch the monitor on the door frame when moving the trolley between rooms
  • always disconnect all power cables from the screens when moving the trolley.
  • when you reach your destination, lock all brakes on the wheels.
  • move and place the trolley only on a flat surface. Any sloping ground may cause the device to lose stability and tip over.
  • pushing the trolley on a smooth floor is much easier than on fluffy carpets. Soft surfaces should be avoided.
  • Driving the wheelchair over an obstacle (e.g. a threshold in a doorway) must always be carried out with the participation of two or more people. The maximum height of the obstacle that can be driven over is 5mm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>