Chicco Next2Me Dream Evo Beige Relux Instruction Manual

Instruction Manual

Next2Me Dream Evo Beige Relux

IMPORTANT – READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.

WARNING: TO AVOID THE DANGER OF SUFFOCATION REMOVE THIS PLASTIC COVER BEFORE USING THE PRODUCT. THIS COVER SHOULD BE DESTROYED OR KEPT AWAY FROM BABIES AND CHILDREN.
WARNINGS

• Only for domestic use.
• WARNING: Do not use this product without reading the instructions for use first.
• WARNING: Stop using the product as soon as the child can sit or kneel or pull himself up.
• WARNING: The product is intended for use by babies aged 0 to 5/6 months, weighing a maximum of 9 kg.
• WARNING: Placing additional items in the product may cause suffocation.
• WARNING: Do not use the product if any part is broken, torn, or missing.
• WARNING: Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/ curtain cords, etc. To avoid all risks of strangulation, never give children ob-jects with cords or strings attached, or leave them within their reach.
• WARNING: Do not use more than one mattress in the product. Only use the mattress that comes with the product.
• Only use the mattress provided with the product or replacement mattress approved by Artsana.
• WARNING: Only use the mattress sold with this crib, do not add a second mattress on this one, suffocation hazards.
• The product must always be placed on a horizontal surface. Never leave the product on a sloping surface with your child inside.
• Unattended children must not be left to play near the product.
• WARNING: When your child is unattended with the product in “crib configuration”, always make sure that the side is raised and locked in alignment with the upper perimeter of the crib.
• All assembly couplings must be fastened correctly. Be sure there are no loose screws, as a child’s body or clothing (e.g., lace, necklaces, pacifier cords) may snag and pose a strangulation hazard.
• WARNING: Be aware of the risk of burns from cigarettes, naked flames, and other heat sources, like electric or gas heaters, that are near the crib.
• WARNING: WHEN not attached to the bed, the crib can be inclined by a maximum of 4 positions between one leg support and the other.
• WARNING: DO NOT USE the product in “Crib Configuration” and/or “Co-Sleeping Configuration” if any part is missing, damaged, or broken. Contact Artsana SPA for spare parts and user instructions if needed. DO NOT REPLACE missing, damaged, or broken parts with non-OEM components or components not approved by Artsana SPA.
• Only use spare parts approved by the manufacturer. Do not attach any accessories to the product that have not been supplied by the manufacturer.
• WARNING: The fixing straps are included in the packaging.  Other fastening systems must NOT be used.
•  When used in the “Co-Sleeping Configuration” (fastened to the bed), the crib must never be inclined.
• To prevent the danger of choking due to the child’s head being trapped, when the crib is in the “Co-Sleeping Configuration” (fastened to the bed) it must be properly fastened to the parents’ bed using the fixing straps as explained in the instruction booklet.
• WARNING: Before placing the child inside the crib when the product is in the “Co-Sleeping Configuration” (fastened to the bed), be sure that the fixing straps are fastened and tightened correctly. The product must be attached to the parents’ mattress and there should be no gaps between the lowest part of the co-sleeping crib and the parents’ mattress.
• Before using in “Co-sleeping configuration (fastened to bed),” make sure the product is fastened and positioned correctly. Check the fasten- ing system hold before each use by attempting to push the crib away from the parents’ bed.
• If there are gaps between the low- est part of the co-sleeping crib and the parents’ mattress, DO NOT use the product.
• Do not fill any spaces or gaps between the parents’ mattress and the crib with pillows, blankets, bedsheets, or any other material that may pose a choking hazard.
• DANGER! The Bedside sleeper, when not attached to the adult’s bed, shall have all its sides in place and/or in their highest position.
• WARNING: To avoid hazards from the child’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
• WARNING: To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
• Before assembly, ensure that the product and its components have not been damaged during transportation. In this case, do not use it and keep it out of reach of children.
• WARNING: Consult the user manual for the list of components. Examine the product regularly to make sure that there are no loose, damaged, or missing parts.
• WARNING: Always use all parts needed for each configuration of use.
• Make sure that the adult using the product knows how to do it in accordance with the manufactures instructions.
• WARNING: The product is ready for use only when all locking mechanisms are engaged. Make sure they are securely engaged before use.
• When the product is being used, especially in “crib configuration”, the wheels must always be locked.
• All operations for opening, adjusting, fastening, and positioning the product must be carried out by an adult.
• Do not use the product without the frame.
• Keep the fastening straps out of reach of children.
• Infants can suffocate on soft bedding. Avoid placing pillows or similar items under newborn babies for additional comfort during sleep.
• Use the crib in “Bedside sleeper Con figuration (fastened to the bed)” only with beds of the size indicated in the reference figure at the beginning of the manual.
• Do not leave anything inside the product that might reduce its depth.
• To prevent the child from being trapped, do not place the crib close to walls or obstacles.  Do not leave any small objects inside the product that might be swallowed.
• Do not make adjustments to the product when the child is in it.
• Do not move the product when the child is inside.
• Do not use the product with more than one child at a time.
• Prolonged exposure to direct sunlight may cause the product’s color to fade. After prolonged exposure of the product to high temperatures, wait a few minutes prio to put your child in it.
• WARNING: Be careful when the child is in the crib, that objects or bedding items do not fall into the crib. • Keep the product out of reach of children when it is not in use.

COMPONENTS

A. Leg rest with wheels
A1. Height adjustment button
A2. Height indicator
A3. Telescopic foot release button
A4. Telescopic feet
A5. Wheels with brakes
A6. Bottom bar slots
A7. Housing for the top part of the crib
B. Bottom bar
C. Crib structure
C1. Fabric
C1.1. Front vertical zippers
C1.2. Upper hinge
C1.3. Fabric attachment buttons
C2. Structure/leg support fasteners
C2.1. Buttons for attaching/releasing the top structure
C2.2 Lever for attaching/releasing the bottom structure
C3. Side panel opening button
C4. Top tube
C5. Crib bottom
C6. Front strap fastening buckle
C7. Rear strap fastening buckle
C8. Mattress stopper
D. Fastening straps
D1. Red crib front fastening buckle
D2. Grey crib rear fastening buckle
D3. Grey bed fastening and height adjustment buckle
E. Mattress with removable lining
F. Bag

ASSEMBLY OF THE CRIB

1. Hold the bottom support A and insert the lower bar B in the appropriate slot A6 (Fig.1), pushing the metal pin until you hear the click. Repeat the same operation for both feet (Fig. 2).

2. Hold the top tube C4 and have it rotate by 90° (Fig. 3). Repeat the same operation for the bottom of the crib C5 (Fig. 4).

3. Close the vertical front zippers C1.1 (Fig.5) and then the upper hinge C1.2(Fig.6).

4. Fasten the buttons C1.3 are located in the upper front corners, and in the front and rear areas of the bottom of the crib (Fig.7-8-9)

5. Fasten the crib structure C to legs A inserting the couplers C2 in the A7 supports located on both legs (Fig.10-11).
   Be careful to position structure C so that the tilting front panel faces in the same direction as the telescopic feet A4.

6. Place mattress E in crib C. Make sure the mattress rests against the stopper C8 (Fig.12).

7. Block the 4 wheels A5 of the crib by lowering the levers that activate the brakes (Fig.13). The crib is now ready to be used.

ADJUSTING THE CRIB HEIGHT
The height of the crib can be adjusted in 11 different positions. To adjust the height, press button A1 on the leg support A and lift or lower the structure C to the desired position (Fig.14). Release after hearing the click.
The base of the crib can be slightly inclined by adjusting the 2 leg supports to different heights (fig.15).
WARNING: The crib can be inclined by a maximum of 4 positions between one leg support and the other ( e.g., right leg support in position 5 and left leg support in position 1) (Fig. 16).
WARNING: Thecvx child’s head must always be positioned near the raised end (fig.17).
SIDE SLEEPING CONFIGURATION (FASTENING THE CRIB TO THE BED)
The crib can be fastened to the parents’ bed (side sleeping configuration).
WARNING – IMPORTANT FOR YOUR CHILD’S SAFETY:
This configuration is allowed only with beds that allow compliance with all the conditions described in this paragraph.
In particular, the lowered side of the crib must always be positioned against the mattress of the parent’s bed and the top of the parents’ mattress must be aligned with (or at most higher than) the height of the open side of the crib (fig.18A-18B). Moreover, the crib must be fastened to the structure of the parent’s bed or to the mattress support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in the side sleeping configuration does not interfere with the parent’s bed.
WARNING: During use, make sure that the bed sheets, blankets, etc. do not interfere with the crib’s space.
WARNING: Check that the size of your bed is compatible with the straps provided. If the straps are too short for proper installation, an additional set of straps can be purchased and attached to the ones that were provided with the product to lengthen them.

1. Lower the side of the crib by pushing button C3 and accompanying the side until it reaches the end of its travel (Fig.19).
   WARNING: Use the crib with the side lowered only in side sleeping mode.

2. Put the crib against the parents’ bed and check its height compared to the parents’ mattress (Fig. 20).
   WARNING: The top of the parents’ mattress must be higher than or the same as that of the side of the crib. If this is not the case, use the adjustment system to achieve this condition on both sides.
   WARNING: In the side sleeping configuration, the 2 feet of the crib must be set at the same height.

3. To fasten the crib to the parents’ bed (co-sleeping configuration), use the included pair of straps D.

4. Carefully release the buckles C7 pushing slightly upwards and then pulling them out (Fig. 21).

5. Fasten the grey buckles D2 to buckles C7 located in the rear part of the bottom of the crib C5 (Fig. 22).

6. Then fasten the red buckles D1 to the buckles C6 located in the front part of the bottom of the crib C5 (Fig. 23).

7. Next, pass the straps around the parents’ bed frame from top to bottom (Fig. 24) and fasten the grey buckles D3 to form a loop (Fig. 25). Make sure to repeat the step on both sides. To make installation easy, when fastening the buckles, always keep the crib slightly away from the parents’ bed.

8. At this point put the crib against the parents’ bed and tighten the noose pulling the straps (fig.26). Carry out this step first on one side and then on the other, adjusting the straps until the crib is in contact with the parents’ mattress.
   WARNING: Before use, always make sure that there is no space between the parents’ mattress and crib’s side. Otherwise, adjust the straps pulling them until the required condition is restored. Make sure that the side is always free to be lowered and raised completely.

9. Lock the crib’s wheels. If fitting the feet of the crib under the parents’ bed while fastening the crib to the bed proves impossible, the bed can be fastened anyway by following the instructions above while also retracting the telescopic feet A4 when setting the crib up against the bed. To activateretr action, simply push the crib towards the bed so that the release buttons A3 (Fig. 27) are activated, retracting the feet much as necessary to install the crib correctly.

10. To close the side, simply lift it upwards, holding it from the center (Fig.28). Always make sure that it is engaged correctly.
    WARNING: Whenever the side is lowered, make sure that the position compared to the parents’ mattress has not changed from that illustrated in the paragraphs above. WARNING: Use the product with beds and/or mattresses with straight sides only. Do not use the product with round beds and/or mattresses or water mattresses.
    To be used with this product, the parents’ bed must have a slat- ted or mesh frame.
    WARNING: When the product is used in a co-sleeping configuration (fastened to the bed), it must always be mounted on the long side of the bed. DO NOT install the product at the head or feet of the bed.

CARE AND MAINTENANCE

The crib and mattress have a resistant fabric lining that can be removed completely and washed. To remove the fabric, follow the instructions in the paragraph “REMOVING THE FABRIC.”
WARNING: Covering or removing the fabric may take a few minutes and must be carried out by an adult. Regularly inspect the product for signs of wear and damage. In the case of damage, do not use it and keep it out of reach of children.
When washing the fabrics pay close attention to the instructions on the label. Do not use solvents or abrasive or overly aggressive products.

|   Machine washable at 30°C
---|---
|   Do not bleach
|   Do not tumble dry
|   Do not iron
|   Do not dry clean

Check that the fabric and the stitching are in good condition after each wash.
WARNING: When covering or removing the cover, take care when handling the fabric parts to avoid accidental tears or damage.
WARNING: The fabric part of the tilting side cannot be removed.
MAKING THE BED
The crib can be unfastened from the parents’ bed when making the bed. Just unfasten the grey buckles under the fabric lining. When fastening the crib again to the parents’ bed, pull the straps again to make sure that the crib is correctly and securely fastened to the parents’ bed. Make sure that all the steps illustrated above in “Co-sleeping configuration (fastened to the bed)” have been completed.
REMOVING THE COVER

1. Remove the mattress.
2. Release the fastening buttons C1.3.
3. To unfasten frame C from feet A, free the bottom part by pulling the lever C2.2 outwards (Fig. 29) and the top part by pressing the two buttons C2.1 located on either side (Fig. 30). Then pull upwards on the frame.
4. Open the 3 zippers C1.1 and C1.2 on the fabric.
5. You can now remove the fabric lining.

DISASSEMBLING THE CRIB
The crib can be disassembled completely to put away in the supplied bag. In order to complete the disassembly of the crib after removing the fabric, remove the lower bar B, repeating the steps illustrated in “ASSEMBLY OF THE CRIB” in reverse order.
WARRANTY
The product is guaranteed against any conformity defect in normal conditions of use as described in the instructions. The warranty shall not, therefore, apply in the case of damage caused by improper use, wear, or accidental events. For the du- ratio of the warranty on conformity defects please refer to the specific provisions of applicable national laws in the country of purchase, where appropriate.
NOTE …………….

EN 16890:2017
ARTSANA S.p.A.
Via Saldarini Catelli, 1
22070 Grandate (CO) – Italy
Tel. (+39) 031 382 111
Fax (+39) 031 382 400
www.chicco.com
46 079695 000 000_2123

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>