metabo RF 60 Air Digital Tyre Inflator and Pressure Gauge Instruction Manual
- June 12, 2024
- metabo
Table of Contents
metabo RF 60 Air Digital Tyre Inflator and Pressure Gauge
Product Information:
The product is a tyre inflation measuring device designed to measure tyre air pressure and inflate tyres. It is suitable for use with oil-free compressed air or nitrogen, and an upstream filter must be used if oily air is used. The device has a pressure gauge that can display the measuring unit in BAR, PSI, KG/CMQ, or Kpa. It is powered by two lithium batteries (1.5 V, type AAA). The device is calibrated before delivery and requires recalibration by the user after the specified test period. The calibration is valid for 2 years.
Product Usage Instructions:
- Connect the tyre inflation measuring device to the compressed air supply using the screw connection or coupling.
- Press the connector (4) firmly onto the tyre valve and secure it with the locking lever (3). Hold onto the hose.
- Read off the tyre pressure at the scale.
- To inflate the tyre, pull the lever (2) up fully. To release or reduce pressure, pull the lever (2) only as far as the first stop (middle position).
- To switch on the pressure gauge, press the ON button. Press the ON button again until the desired measuring unit is displayed.
- After approximately 15 seconds of inactivity, the pressure gauge will switch off automatically.
- To change batteries, remove the screw with a small screwdriver and replace the batteries with two lithium batteries (1.5 V, type AAA), ensuring correct polarity.
- Take care when using the pressure gauge to avoid bumps and knocks.
- For maintenance and care, refer to the user manual.
- Dispose of the product and packaging materials according to national regulations on environmentally compatible disposal and recycling.
- Repairs must be carried out by qualified specialists using original Metabo spare parts. Contact your Metabo service centre for repairs.
Parts
Operating instructions
Specified use: The tyre inflation measuring device is designed to measure
tyre air pressure to inflate tyres.
The user bears sole responsibility for any damage caused by improper use.
Safety instructions: The maximum supply pres-sure specified on the air tool
must never be exceeded.
Only operate with oil-free compressed air or nitrogen; an upstream filter must
be used if oily air is used!
Keep air tools away from children.
Initial operation: Connect tyre inflation measuring device (using screw
connection or coupling) to the compressed air supply.
Operation: Press the connector (4) firmly onto the tyre valve and secure
on tyre valve with locking lever (3). Hold on to the hose.
-
RF 80 G:
Read off tyre pressure at scale. To inflate, pull lever up (2) fully. To release / reduce pressure, pull lever (2) only as far as the 1st stop (middle position). -
RF 60 / RF 60 G:
Read off tyre pressure at scale. Pull lever (2) to inflate. To release / reduce pressure, press the pushbutton (1). -
RF 80 D (with digital pressure):
Press the “ON” button to switch on the pressure gauge. Press the “ON” button once again until the desired measuring unit is displayed (BAR → PSI → KG/CMQ → Kpa). After approx. 15 seconds, the pressure gauge switches off automatically. To inflate, pull lever up (2) fully. To release / reduce pressure, pull lever (2) only as far as the 1st stop (middle position).
Changing batteries: remove the screw with a small screwdriver. Remove the
batteries and replace them, ensuring that polarity is correct. (2 lithium
batteries 1.5 V, type AAA).
Maintenance and care: Take care when using the pressure gauge and keep it
in good condition. Avoid bumps and knocks.
RF 80G, RF 60G: The device is calibrated before delivery and must be submitted
by the user for recalibration after the test period has elapsed. The test
period is specified on the device. Validity of cali-bration: 2 years. (German
Weights and Measures Act section 35)
Storage: cleaned, dry, dust-free, not below 5° C.
Environmental protection: Observe national regulations on environmentally
compatible disposal and on the recycling of disused pneumatic tools, packaging
and accessories. You must not cause risks to people or the environment.
Packaging materials must be disposed of according to their labelling in
accordance with municipal guidelines. Further information can be found at
www.metabo.com in the “Service” section.
Repair: Danger! Repairs must be carried out by qualified specialists only
using original Metabo spare parts! Please contact your Metabo service centre.
See www.metabo.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>