SEALEY VS0220 Brake and Clutch Bleeder Pneumatic Vacuum Instruction Manual
- June 12, 2024
- SEALEY
Table of Contents
PREMIER 1.2L PNEUMATIC VACUUM
BRAKE & CLUTCH BLEEDER
MODEL NO: VS0220
Instruction Manual
VS0220 Brake and Clutch Bleeder Pneumatic Vacuum
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
|
---|---
Refer to instruction manual| Wear eye protection
SAFETY
Familiarise yourself with the applications and limitations, as well as
any potential hazards, of the kit.
Keep this product in good working order and condition. (take immediate
action to repair or replace damaged parts).
Use approved parts only (unapproved parts may be dangerous and will
invalidate the warranty).
Keep children and unauthorised persons away from the work area.
Keep work area clean and tidy and free from unrelated materials.
Ensure the work area has adequate lighting.
DO NOT use the kit to perform a task for which it is not designed.
DO NOT allow untrained persons to use the kit.
DO NOT use whilst under the influence of drugs, alcohol or intoxicating
medication.
After use, clean equipment and store in a cool, dry, childproof area.
Dispose of waste liquids in accordance with local authority regulations.
Always read and comply with the warnings on the brake fluid container.
Wear eye protection and keep skin contact to a minimum. If brake fluid
enters eyes, rinse with plenty of water and seek medical advice. If swallowed
seek medical advice immediately.
◻ WARNING! Brake fluid is flammable – keep away from sources of ignition,
including hot surfaces e.g. exhaust manifold.
◻ WARNING! Brake fluid will damage paintwork. Any spillage should be
flushed with water immediately.
**** After use, clean equipment and store in a cool, dry, childproof area.
INTRODUCTION
One-person operation using standard workshop air supply (87-174psi/6-12bar).
With a flexible hanging hook. Durable hard-wearing Acetal plastic.
Trigger for adjusting air pressure, with an added trigger lock. Draws fluid
from the bleeding nipple enabling either bleeding or full replacement of fluid
in the system. Clear PVC hose easily checks for air bubbles. Hose length 1.5m.
Does not require specialised brake reservoir caps.
SPECIFICATION
Model No:……………………………………………………….. VS0220
Air Consumption: ……………………………………………. 180L/min
Inlet Size: …………………………………………………………1/4”BSP
Maximum Air Supply: …………………………………. 174psi/12bar
Tank Capacity: ………………………………………………………. 1.2L
OPERATION
Numbers refer to diagram below.
4.1. With this brake bleeder, one person can carry out the bleeding of the
brake systems. Bleeding is completed quickly, cleanly and simply.
Brake fluid is sucked into the container avoiding unnecessary spillages.
4.2. Connect the gun to the compressed air line system (1).
4.3. Set the brake bleeder’s rubber pipe on the bleed screw, and loosen
the bleed screw (2).
4.4. Activate the handle of the brake bleeder, a partial vacuum is
created in the brake bleeder container, and the fluid is sucked into the
container (3).
4.5. When the brake fluid is free of air bubbles, which can be seen
through the clear hose (4), then tighten the bleed screw and remove the rubber
pipe.
4.6. Repeat the procedure for each brake calliper.
4.7. REMEMBER to check brake fluid level in reservoir
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
https://qrco.de/bcy2E9
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
VS0220 Issue 2 (2,3) 22/03/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>