BOCCI 21.26 Rectangle Raw Porcelain Pendants Instruction Manual
- June 4, 2024
- BOCCI
Table of Contents
21.26 Rectangle Raw Porcelain Pendants
21.26 Rectangle Raw Porcelain Pendants
Instruction Manual 
180 (7”)
±130 (5”)
53 (2”) up to 3000 (10’)
standard 53 (2”)
up to 30500 (100’) custom
335 (13.2”) 205 (8”)
870 (34.38”) 1000 (39.4”)
approx 28.4kg (62.6lb)
| PENDANTS: | twenty-six |
|---|---|
| MOUNTING: | white powder-coated rectangular canopy 1000mm (39.4”) x 335mm |
(13.2”) x 53mm (2”) deep
LAMPING:| 1.5w LED or 20w xenon
COAX:| non-adjustable lengths. 3000mm (10’) standard / up to 30500mm (100’)
maximum
MATERIALS:| porcelain, borosilicate glass, braided metal coaxial cable,
electrical components, white powder-coated canopy
WEIGHT:| approximately 25kg (55lb)
POWER SUPPLIES| integral
DESCRIPTION
21.26 is a random confi guration of twenty-six 21 pendants hung from a
rectangular canopy. The drop lengths of the pendants are randomized between a
client specifi ed range of heights to variously cluster and scatter. The result
is an ambient installation or fi eld of light.
Inspired by the sporadic, discordant arrangement of barnacles on a rock
surface, the 21 is fabricated from thin sheets of porcelain wrapped around a
trumpet-shaped borosilicate diffuser. Each diffuser houses a low-voltage lamp.
A strong contrast is established between the organically distributed soft
light passing through the white porcelain skin and the sharp, crisp light
passing through the borosilicate glass diffuser.
NOTES
+ Purchase replacement lamps online at
www.bocci.com/shop/bulbs
+ Unless otherwise noted when ordering, all chandeliers will be outfi tted to
be xenon compatible.
+ As an alternative to built-in power supplies, Bocci recommends mounting
power supplies remotely in an easily accessible and hidden location for ease
of long-term maintenance.
-
Note: All connections and power supplies are tested by our technicians before shipping.
However, it is possible for ports/ power supplies to come loose or damage during shipping.
Test each port before installing the canopy to the ceiling to catch any loose connections or faulty power supplies.
Measure and mark the light fi xture canopy position on the ceiling
-
Note: The client is responsible for providing a robust 16mm (5/8”) plywood backing or wood blocking to securely anchor to the structural substrate.
Connections from the plywood to the structural substrate are the client’s responsibility.
Measure the plywood so that it fi ts within the canopy side walls (refer to detail above).
Anchor the plywood backing to the structural ceiling substrate.
-
Connect power supplies to line voltage.
Xenon (110V) or LED: connect the black wire to the black and the white wire to the white wire.
Xenon (230V): connect black wire to brown wire and white wire to blue wire.
For the ground connection, connect the green wire with a yellow stripe to the bare copper wire or green wire in the junction box.
Note: Bocci strongly recommends mounting power supplies remotely in a close, accessible and hidden location for ease of long-term maintenance. Installation to be done by certain ed personnel to ensure compliance with the code.
-
Anchor the canopy into the plywood backing using the fasteners provided.
Turn power to fi xture on.
Very carefully uncoil the braided coaxial cable in a spool-like manner. Insert your index fi ngers into opposite sides of the roll then rotate your fi fingers around each other
to unroll the coaxial cable.
Use patience: allow the cable to uncoil completely to avoid kinks.
-
Bocci LED or xenon lamps are included. Lamping is power supply specifi c.
Plug the lamp into the socket.
Do not touch the lamp with your bare hands. Ensure power to the lamp is working correctly.
Thread the coaxial cable through the shade, followed by the borosilicate diffuser, and the cap, and finally close off the diffuser with the diffuser gasket.
-
Each pendant terminates in a “headphone jack” type connector, which plugs into a receiving receptacle in the canopy. Clients are encouraged to compose their own pendant confi guration on site, thus creating a truly unique fi xture. After plugging in each pendant, turn the threaded sheath into place by hand ensuring that it is adequately tightened. Tools are not required.
Check that each lamp is working properly as you go along by keeping power to the fi xture on and lamps plugged in. -
Clean fi fingerprints from surfaces.
For additional assistance, please contact Bocci:
Vancouver
sales@bocci.com
www.bocci.com| Berlin
europe@bocci.com
www.bocci.com
---|---
US patent # US D556,361
Worldwide patents issued and pending.
Made in Vancouver, Canada LOW VOLTAGE LUMINAIRE
E476186
© 2021, Bocci Design and Manufacturing Inc. All rights reserved. Any inquiries
should be directed to: info@bocci.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>