Godox RC-R9II Remote Control Instruction Manual
- June 4, 2024
- Godox
Table of Contents
R9II Remote Control
Instruction Manual
Names of Parts
01. OLED Panel
02. Power Switch
03. Wireless Setting Button
04. FX Mode Button
05. CCT Bicolor Mode Button
06. HSI Colorful Light Mode Button
07. FN Button
08. DIM Brightness Adjustment Button
09. 3200K Color Temperature Button
10. 5600K Color Temperature Button
11.6500K Color Temperature Button
12. Red Button
13. Green Button| 14. Blue Button
15. Cyan Button
16. Magenta Button
17. Yellow Button
18. Pink Button
19. Violet Button
20. Orange Button
21. Battery Compartment
22. Battery Compartment Cover
23. Up Button
24. Left Button
25. Right Button
26. Down Button
---|---
Remote Control Setting
Short press the power switch button to power on or off the remote control.
Remote Control Channel/Group/ID Adjustment
Press the wireless setting button to enter the channel/group/ID setting interface.
CH
Setting: Press the up and down button to choose the CH channel and press the
left or right button to choose the channel value from 1 to 32.
GR
Setting: Press up and down button to choose GR group and press left or right
button to choose group value from A to F and 0 to 9.
ID
Setting: Press up and down button to choose ID and press the left or right
button to choose the ID value from 1 to 99.
FX Modes Setting
Press FX to enter FX modes and press left or right button to choose their
categories of them. After choosing the kinds, there are I, II and Ill modes
can be selected. There are 39 kinds of situational FX modes which are divided
into 14 categories for your choice.
No.| Display| Situation| Display I| Display II|
Display Ill
---|---|---|---|---|---
1| | Colorful lights recycle| Slow speed| Medium speed| Quick speed
2| | Flash| Flash| Press conference| Paparazzi
3| | Party| Birthday party| KTV| Disco
4| | Lightning| Discontinuous| Frequent| Sustainable
5| | Broken bulb| Discontinuous| Frequent| Sustainable
6| | TV| Slow speed| Medium speed| Quick speed
7| | Candle| Discontinuous| Frequent| Sustainable
8| | Fire| Firewood| Campfire| Fi re hazard
9| | Firework| Brief| Continuous| Show
10| | Police car| Strong flash| Frequent flash| Quick flash
11| | Firetruck| Strong flash| Frequent flash| Quick flash
12| | Ambulance| Strong flash| Frequent flash| Quick flash
13| | Music| Music I| Music II|
14| SOS| SOS| | |
Bicolor Modes
Press the CCT button to enter bicolor modes and press up, down, left and right
buttons to choose the color temperature from 2500K to 8500K. Pressing the up
and down button will change the color temperature by ±1000 per time while
pressing the left and right buttons by ±100 per time. You can also choose
3200K, 5600K, and 6500K directly by pressing the corresponding buttons.
Colorful Light Mode Setting
Press the HSI button to enter colorful light modes. Adjust hue H: press the up
or down button to choose hue H. Then, press the left or right button to adjust
hue value from 0 to 360°.
Adjust
saturation S: press the up or down button to choose saturation S. Then, press
the left or right button to adjust the saturation value from 0 to 100.
You can also choose Red, Green, Blue, Cyan, Magenta, Yellow, Pink, Violet, and Orange colors directly by pressing the corresponding buttons.
Light Brightness Adjustment:
-
When the current single light’s brightness is displayed, press the DIM “+ “or ” – “button to adjust the brightness from 0 to 100%.
-
Turn on/off the single group’s brightness: press the wireless setting button to enter the wireless setting interface. Press the up or down button to choose the group GR and press the FN button to turn on or off the single group’s brightness. When the brightness is off, OFF will be displayed. When the brightness is on, figure 0 to 100 will be displayed.
Note: Wireless signals can only be received when the receiving end is powered on.
Technique Data
| Remote Control | RC-R911 |
|---|---|
| Power Supply | 3.0V(AAA*2)(battery not included) |
| 2.4G Frequency Range | 2413.0MHz-2464.5MHz |
| Max. Transmitting Power | 5dbm |
| Distance(empty) | 100m |
| Channel | 32(1 to 32) |
| Grouping | 16 Group(A BC D E F, 0 to 9) |
| ID | 99 (1-99) |
| Working Environment Temperature | -10-40°C |
| Dimension | 55x133x10mm |
| Net Weight | 63g |
Warning
Operating frequency: 2413.0MHz-2464.
5MHz Maximum EIRP Power: 5dBm
Declaration of Conformity
GODOX Photo Equipment Co., Ltd. hereby declares that this equipment are in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10),
this product is allowed to be used in all EU member states.For more
information of DoC, Please click this web link:https://www.godox.com/DOC
/-Godox_RC-R911_DOC.pdf. The device complies with RF specifications when the
device used at Omm from your body.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
Warranty
Dear customers, as this warranty card is an important certificate to apply for
our maintenance service, please fill in the following form in coordination
with the seller and safe-keep it. Thank you!
| Product Information | Model | Product Code Number |
|---|---|---|
| Customer Information | Name | Contact Number |
Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:
Note: This form shall be sealed by the seller.
(Applicable Products)
The document applies to the products listed on the Product Maintenance
Information (see below for further information). Other products or accessories
(e.g. promotional items, giveaways and additional accessories attached, etc.)
are not included in this warranty scope.
(Warranty Period)
The warranty period of products and accessories is implemented according to
the relevant Product MaintenanceInformation. The warranty period is calculated
from the day(purchase date) when the product is bought for the first time, And
the purchase date is considered as the date registered on the warranty card
when buying the product.
(How to Get the Maintenance Service)
If maintenance service is needed, you can directly contact the product
distributor or authorized service institutions. You can also contact the Godox
after-sale service call and we will offer you service. When applying for
maintenance service, you should provide a valid warranty card. If you cannot
provide valid warranty card, we may offer you maintenance service once
confirmed that the product or accessory is involved in the maintenance scope,
but that shall not be considered as our obligation.
(Inapplicable Cases)
The guarantee and service offered by this document are not applicable in the
following cases: O. The product or accessory has expired its warranty period;
C). Breakage or damage caused by inappropriate usage, maintenance or
preservation, such as improper packing, improper usage, improper plugging
in/out external equipment, falling off or squeezing by an external force,
contacting or exposure to the improper temperature, solvent, acid, base,
flooding and damp environments, etc; ®. Breakage or damage caused by the non-
authorized institution or staff in the process of installation, maintenance,
alteration, addition and detachment; ®. The original identifying information
of the product or accessory is modified, alternated, or removed; ®. No valid
warranty card;. Breakage or damage caused by using illegally authorized,
nonstandard or non-public released software; C). Breakage or damage caused by
force majeure or accident; ®. Breakage or damage that could not be attributed
to the product itself. Once met these situations above, you should seek
solutions from the related responsible parties and Godox assumes no
responsibility. The damage caused by parts, accessories, and software that is
beyond the warranty period or scope is not included in our maintenance scope.
The normal discoloration, abrasion, and consumption are not breakages within
the maintenance scope.
Maintenance and Service Support Information
The warranty period and service types of products are implemented according to
the following Product Maintenance Information:
Product Type| Name| Maintenance Period(month)| Warranty
Service Type
---|---|---|---
Parts| Circuit Board| 12| The customer sends the product to the designated
site
Battery| 3| The customer sends the product to the designated site
Electrical parts e.g.battery charger, etc.| 12| The customer sends the product
to the designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device,
package, power cord, sync cable, etc.| No| Without warranty
Godox After-sale Service Call 0755-29609320-8062
GODOX Photo Equipment Co., Ltd.
Add: Building 2~ Yaochuan Industrial Zone,
Tangwei Community~ Fuhai Street~ Baoan District, Shenzhen~
China Tel: +86-755-29609320(8062) Fax: +86-755-25723423
Email: godox@godox.com
godox.corn
Made in China I 705-RCR9OO-02
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>