AIROLITE K6746X 6 Inch 152.4 mm Deep Drainable Louver Instruction Manual
- June 12, 2024
- AIROLITE
Table of Contents
AIROLITE K6746X 6 Inch 152.4 mm Deep Drainable Louver
Product Information
Part Number: 475584
Model: K6746X
This product is a louver designed for installation in a specific equipment or system. It is important to follow the installation, operation, and maintenance instructions provided in this manual to ensure proper functioning and longevity of the product.
Product Usage Instructions
Receiving and Handling:
- Upon receiving the louver(s), carefully inspect for any visible damage.
- If any damage is found, record all necessary information on the bill of lading.
- File a claim with the final carrier for any damages.
- Check and ensure that all parts of the shipment, including accessories, are accounted for.
Safety Warning:
It is important to follow safety guidelines to prevent property damage,
injury, or death. Before installing or servicing this equipment, thoroughly
read and understand the installation, operating, and maintenance instructions
provided in this manual.
Storage:
Store the louver(s) in a clean, dry, and secure location. Avoid exposing it to
extreme temperatures, moisture, or direct sunlight. Proper storage will help
maintain the integrity and functionality of the product.
Maintenance:
Regular maintenance is crucial to ensure optimal performance of the
louver(s). Follow the maintenance instructions provided in this manual,
including cleaning recommendations, lubrication requirements, and inspection
schedules. Adhering to these guidelines will help extend the lifespan of the
product.
Warranty:
Details about the warranty coverage for this product are not provided in this
text-extract. Please refer to the complete user manual or contact the
manufacturer for warranty information.
Part # 475584
Installation, Operation and Maintenance Instructions Model K6746X
This manual is the property of the owner, and is required for future maintenance. Please leave it with the owner when the job is complete.
RECEIVING AND HANDLING
Upon receiving the louver(s), check for both obvious and hidden damage. If
damage is found, record all necessary information on the bill of lading and
file a claim with the final carrier. Check to be sure that all parts of the
shipment, including accessories, are accounted for.
SAFETY WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating, and
maintenance instructions thoroughly before installing or servicing this
equipment.Z
STORAGE
The louvers and components are shipped in semi-enclosed wooden crates, and
should be left in the crate until ready for installation. Inside storage is
preferable. If outside storage is required, the crates should be blocked up or
otherwise elevated from the ground or pavement, and covered securely with
waterproof coverings of plastic film. Wraps “Coverall” or “Visqueen” film
sheeting is recommended as adequate protection, however, any plastic film
waterproof sheeting of equal quality is acceptable. Louvers and components are
not wrapped or protected from moisture or dirt within the wooden crates. If
prolonged storage is anticipated, either inside or out in the weather,
adequate steps should be taken to protect the units and their finishes. It is
also possible to order individual section plastic wrap when long term storage
is anticipated. Handling to and from storage should be accomplished with the
wooden crates intact. Physical damages, marred finishes, loss of loose parts
and fasteners, and separation of associated components may occur if crates are
dismantled and louver components removed to facilitate storage.
GENERAL NOTES:
- IT SHALL BE THE RESPONSIBILITY OF THE PERMIT HOLDER TO VERIFY THE STRUCTURAL INTEGRITY OF THE EXISTING STRUCTURE TO SUPPORT THE LOADS SUPERIMPOSED BY THE LOUVERS.
- INSTALLER TO PROVIDE SEPARATION OF DISSIMILAR MATERIALS AS REQUIRED.
- WOOD SUBSTRATE TO BE MINIMUM G = 0.42 DENSITY.
- CONCRETE SUBSTRATE TO BE MINIMUM 3,200 PSI.
- STEEL STUD OPENINGS (16 GA MINIMUM THICKNESS TO BE MINIMUM Fy = 33 ksi 6
- STRUCTURAL STEEL OPENINGS (1/4″ MINIMUM THICKNESS) TO BE MINIMUM Fy = 36 ksi
MAINTENANCE
Stationary or fixed blade louvers require no maintenance to remain functional.
The louver finish may be subject to deterioration dependent solely upon the
environment in which sun controls are installed. Appearance and longevity of
the finish may be greatly extended by an occasional cleaning, the frequency of
which, is again solely dependent upon the environment. Proper cleaning may be
accomplished with the use of a light scrubbing action, used in conjunction
with a good grade of common household mild detergent. Harsh acidic or caustic
cleaners are not recommended. Under no condition should the louver or
component finish be scrubbed with an abrasive cleaner or apparatus.
WARRANTY
Airolite warrants this equipment to be free from defects in material and workmanship for a period of one year from the shipment date. Any units or parts which prove to be defective during the warranty period will be repaired or replaced at our option. Airolite shall not be liable for damages resulting from misapplication or misuse of its products. Airolite will not be responsible for any installation or removal costs. Airolite will not be responsible for any service work or backcharges without prior written authorization.
Copyright © 2012 The Airolite Company, LLC Part# 475584 June 2012 Rev 1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>