RED SHED 1859156 6.5 FT Freedom Fir With 250 Clear Lights Instruction Manual

RED SHED 1859156 6.5 FT Freedom Fir With 250 Clear Lights

Product Information

• Product Name: 6.5 FT FREEDOM FIR with 250 CLEAR LIGHTS
• SKU: 1859156
• Assembly Time: Approximately 30 Minutes
• Required Assembly Space: 4 FT x 4 FT
• Parts List:
  • No. 1: Metal Stand
  • No. 2: Pre-Lit Tree Section A
  • No. 3: Pre-Lit Tree Section B
  • No. 4: Pre-Lit Tree Section C
  • No. 5: 3-Amp 125V Replacement Fuse (Quantity: 3)
  • No. 6: Screw (for metal stand) (Quantity: 1)
  • No. 7: Replacement Bulb (Quantity: 10)

Product Usage Instructions

1. Assemble the tree stand on a level surface. Twist open the base and tighten the screws at the top of the base to secure the legsinto place.
2. Identify the tree sections labeled with tags: A (top section), B (middle section), and C (bottom section). Remove the caps from the pole ends.
3. Insert the bottom section (C) into the assembled stand, ensuring it is firmly inserted and secured. Then insert the middle section (B) into the bottom section (C), followed by the top section (A) into the middle section (B).
4. Plug section A into section B and plug section B into section C.
5. Gently shape all branches and tips into place, starting with the tips closest to the interior pole. Position one tip to the right, one tip to the left, and one at the center of each main stem for each branch.
6. Plug the tree into a wall outlet.
7. If the entire tree or any tree section does not light up, check the connections of all plugs and ensure the power cord is properly plugged into the wall outlet.
8. If a light set fuse needs replacement, follow these steps:
9. Disconnect the string of lights that are not lighting up from the working light sets.
10. Slide the access cover on top of the plug towards the prongs to locate the blown fuse.
11. Turn the plug over to remove the blown fuse. The fuse should fall into your hand. Gentle tapping may be required to dislodge it.
12. Locate spare replacement fuses in the spare parts bag and insert a new fuse.
13. Close the fuse cover by sliding the fuse access cover towards the cord.

USE AND CARE INSTRUCTIONS

• Inspect product carefully before using or reusing.

• To store, disassemble the tree and place in its original box. Store tree in a cool dry place where the temperature does not exceed 100 degrees Fahrenheit.

• This product is for indoor use only and is for decoration only.

• Not a toy and not intended for children.

• If any lights do not work on your pre-lit tree, please check the following

  • If the entire tree, or tree section (top, middle, bottom) does not light check to see if all plugs are properly connected and verify the power cord is plugged into the wall outlet.

  • If a strand of lights doesn’t not light

  • Check that all bulbs tightly fit inside their sockets and ensure no bulbs are broken or missing. Replace broken or missing bulbs with the provided replacement bulbs. See the Bulb Replacement section for further instructions). If all bulbs are firmly in the sockets, slightly twist the bulbs from side to side to ensure proper connection.

  • Check the fuse in the mini light cord and replace if necessary.
    IMPORTANT: This is the only time you should remove the tape wrapping the outlets of the mini lights. Please remove tape to inspect 3-Amp fuse and replace tape to original condition after inspecting.

  • If the lights still do not work, carefully remove each bulb, one by one, from the problem light string. Pull both the bulb and plastic base straight out of the socket. Do not twist bulbs while removing from sockets. Check the two wires located at the bottom of the bulb holder. Each wire should be aligned properly on the bulb holder to ensure a proper connection with the lamp socket. If one wire is missing, or too short, please replace it with the provided replacement bulb.

• Fuse Replacement: This product comes with overload protection (fuse). A blown fuse indicates an overload or short circuit. If a fuse blows, first unplug tree from the wall outlet. Then, replace the fuse, per the instructions below and follow product marking for the proper fuse rating. If the replacement fuse blows, a short circuit may occur, and the product should be reviewed to determine the cause.

  • Light set fuse replacement (replaceable 3-amp 125V fuses are located inside the plug, as seen in Figure 3.)
  • Disconnect the string of lights that will not light from the working light sets.
  • Locate the blown fuse by sliding access cover on top of the plug towards prongs.
  • Remove the blown fuse by turning the plug over. The fuse should fall into your hand. Gentle tapping may be required to dislodge the fuse.
  • Locate the spare replacement fuses in the spare parts bag.
  • Insert the new fuses. Close the fuse cover by sliding the fuse access cover towards the cord.
  • CAUTION: To reduce the risk of fire – replace the fuse in mini light sets with only 3-amp 125-volt fuse. Do not replace the attachment plug. Discard the product if the attachment plug is damaged.

• Bulb Replacement

  • Make certain the tree is unplugged from the electrical outlet.
  • Pull the bulb and plastic base straight from its socket. Do not twist bulbs while you are removing them.
  • Additional bulbs are included in the spare parts bag. Replace burned-out bulbs with replacement bulbs included with this product packing only.

Note: This product is for decoration purposes only and is not a toy. It is not intended for children.

Distributed by TRACTOR SUPPLY COMPANY, 5401 Virginia Way, Brentwood TN 37027 For customer support, call 1-888-376-9601 or visit www.TractorSupply.com

Please read instructions carefully before use. Retain for future reference .

Assembled Dimensions

Approximate        30Minutes

Assembly Time

|

People for Assembly

| Required Assembly Space
4 FT x 4 FT
---|---|---

PARTS LIST

No.| Description| Quantity| No.| Description| Quantity|
---|---|---|---|---|---|---
1| Metal Stand| 1| 5| 3-Amp 125V

Replacement Fuse

| 3
2| Pre-Lit Tree Section A| 1| 6| Screw (for metal stand)| 3
3| Pre-Lit Tree Section B| 1| 7| Replacement Bulb| 10
4| Pre-Lit Tree Section C| 1|  |  |

No Assembly Tools Required

IMPORTANT SAFETY INSTRUCTIONS

• When adjusting branches make sure all wires are free from the branch hinges
• This is an electrical product – not a toy! To avoid risk of fire, burns, personal injury, or electrical shock it should not be played with.
• Do not mount or place near gas or electric heaters, fireplaced, candles, or other similar sources of heat.
• Do not cover product with cloth, paper or any material when product is in use.
• Do not hang ornaments or other objects from the cord, wire or light strings. Hang ornaments only on the tree branches.
• For your safety, unplug the product if left unattended.
• Do not let bulbs rest on the supply cord or on any wire.
• Do not close doors or windows on the product or cord as this may damage the wire insulation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>