BOSCH GLI 12V-330 Professional Cordless Light Instruction Manual

: June 12, 2024
: Bosch

Table of Contents

GLI 12V-330 Professional Cordless Light
Safety Notes
Product Description and Specifications
Product Features
Technical Data
Assembly
Operation
Maintenance and Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GLI 12V-330 Professional
HEAVY DUTY

Original instructions

GLI 12V-330 Professional Cordless Light

BOSCH GLI 12V-330 Professional Cordless Light - Fig

BOSCH GLI 12V-330 Professional Cordless Light - Fig 1 |
---|---
|

Safety Notes

Safety Warnings for Cordless Worklights
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Please read and observe all safety warnings and instructions enclosed with the battery or the power tool with which the battery was provided.
Handle the cordless worklight with care. The cordless worklight generates intense heat, which leads to increased danger of fire and explosion.
Do not work with the cordless worklight in hazardous areas.
After the automatic shut-off of the cordless worklight, do not continue to press the On/Off button. The battery could become damaged.
Do not direct the light beam at persons or animals and do not stare into the light beam yourself (not even from a distance).
Use only original Bosch accessories.
Do not cover off the lamp head while operating the cordless worklight. The lamp head heats up during operation and can cause burns when the heat accumulates.
Do not use the cordless worklight in road traffic. The cordless worklight is not approved for illumination in road traffic.
Before any work on the cordless worklight itself (e.g. assembling, maintenance, etc.), as well as when transporting and storing, remove the battery from the cordless worklight.
Do not allow children to use the cordless worklight. It is intended for professional use. Children can unintentionally blind themselves or other persons.
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion.
When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritations or burns.
In case of damage and improper use of the battery, vapours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irritate the respiratory system.
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use the battery only in conjunction with your Bosch product. This measure alone protects the battery against dangerous overload.
The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat.
Keep the cordless worklight away from cardiac pacemakers. The magnet inside the cordless worklight generates a field that can impair the function of cardiac pacemakers.
Keep the cordless worklight away from magnetic data carriers and magnetically sensitive devices. The effect of the magnet can lead to irreversible data loss.
Do not fix the cordless worklight overhead using the magnetic mount. There is a risk of injury if it falls down.
Check whether the magnetic mount can permanently carry the cordless worklight. There is a risk of injury if it falls down.

Product Description and Specifications

Intended Use
The cordless worklight is intended for mobile illumination in limited space and for limited time in dry indoor and outdoor areas and is not suitable for general room lighting.

Product Features

The numbering of the product features refers to the illustration of the cordless work- light on the graphics page.

Lamp head
Battery pack*
Battery unlocking button*
Carabiner
Support stand
Magnetic mount
Utility hook
Tripod mount 1/4″
On/Off switch
Heat sink

*Accessories shown or described are not part of the standard delivery scope of the product.
A complete overview of accessories can be found in our accessories program.

Technical Data

Cordless Worklight		GLI 12V-330
Article number		3 601 DA0 0..
Rated voltage	V=	12
Lighting duration, approx.	min/Ah	180
Weight according to EPTA-Procedure 01:2014	kg	0.5 -0.7*
Luminous flux	Im	330

Permitted ambient temperature
– during charging..
– during operation and during storage| °C
°C| 0… +45
-20…+50
Recommended batteries| | GBA 12V..
GBA 10,8V..
Recommended chargers
The colour rendition of illuminated objects can be distorted. depending on the battery pack being used
Limited performance at temperatures <0 °C| | GAL 12.. CV
AL 11..CV

Assembly

Battery Charging (Accessory)
Note: The battery supplied is partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
The lithium-ion battery is protected against deep discharging by the “Electronic Cell Protection (ECP)”. When the battery is empty, the cordless worklight is switched off by means of a protective circuit.

Do not continue to press the On/Off switch after the cordless worklight has been automatically switched off.The battery can be damaged.

To remove the battery 2, press the unlocking button 3 and pull the battery out of the cordless worklight. Do not exert any force. Observe the notes for disposal.

Operation

Initial Operation
Inserting the battery
Insert the charged battery 2 into the lamp head 1 until you feel it engage.
Switching On and Off
To start the cordless worklight, press the On/Off switch 9.
To switch off the cordless worklight, press the On/Off switch 9 again.
To save energy, only switch the cordless worklight on when using it.
Adjusting the Brightness
Press the On/Off switch 9 briefly to switch on the cordless worklight at maximum brightness. To adjust the brightness in 2 stages, hold down the On/Off switch 9 until the required brightness is obtained.
Temperature Dependent Overload Protection
When exceeding the allowable heat-sink temperature of 50 °C, the cordless worklight switches off. Allow the cordless worklight to cool down, then switch the cordless worklight on again.
Working Advice
The cordless worklight runs at reduced brightness when the battery capacity is at ap- prox. 1.3 %. The cordless worklight flashes 3 times before the brightness decreases.
Swivelling the Lamp Head (see figure A)
The lamp head 1 can be swivelled up to 200° to suit the application.
– As an uplight with the lamp head aimed upwards.
– Swivelled 90° to shine light into the room.
– With lamp head tilted approx. 120° for glare-free lighting of the work area, e. g. a desk.
– With lamp head tilted approx. 200° to illuminate the floor.
Note: At a tilt of more than 90° the cordless worklight has to be fixed.
Utility Hook (see figure B)
You can use the utility hook 7 to attach the cordless worklight to an object.
Carabiner (see figure C)
You can use the carabiner 4 to attach the cordless worklight e. g. to a rope or belt.
Magnetic Mount (see figure D)
You can use the magnetic mount 6 to attach the cordless worklight to ferromagnetic surfaces. Do so carefully in order to avoid scratching delicate surfaces.
Tripod Mount (1/4″) (see figure E)
You can use the tripod mount 8 to screw the cordless worklight onto a tripod.

Maintenance and Service

Maintenance and Cleaning
When the battery is no longer operative, please refer to an authorised after- sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and contains no components that must be replaced ormaintained.

The light source cannot be replaced. If the light source is defective, the entire cordless worklight has to be replaced.

To avoid damage, clean the plastic lens of the cordless worklight only with a dry, soft cloth. Do not use cleaning agents or solvent.

After-sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and re- pair of your product as well as spare parts. Exploded views and information on spare parts can also be found under: www.bosch- pt.com
Bosch’s application service team will gladly answer questions concerning our products and their accessories.
In all correspondence and spare parts orders, please always include the 10-digit article number given on the nameplate of the product.

Great Britain
Robert Bosch Ltd. (B.S.C.) P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.

Tel. Service: (0344) 7360109
E-Mail:boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre 143 Crompton Street Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com

Transport
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
The user can transport the batteries by road without further requirements. When being transported by third parties (e.g.: air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch batteries only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
Please also observe possibly more detailed national regulations.
Disposal
Cordless worklights, battery packs, accessories and packaging should be sorted for environmental-friendly recycling.
Do not dispose of cordless worklights and batteries/rechargeable batteries into household waste!
Only for EC countries:
According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment, cordless worklights that are no longer usable, and according to the EuropeanGuideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.

Batteries no longer suitable for use can be directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park North Orbital Road Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Battery packs/batteries:
Li-ion:
Please observe the instructions in section “Transport”, page 23.
Subject to change without notice.