Homewell HMW-ARP2000 Electric Water Pump Instruction Manual
- October 30, 2023
- Homewell
Table of Contents
Homewell HMW-ARP2000 Electric Water Pump Instruction Manual
Thank you for purchasing the HOMEWELL water pump.
This is a versatile pump ideal for fish ponds, fountains, waterfalls, and
other water features. This submersible/external water pump is designed for
continuous operation.
The unit comes assembled and is ready to use. Simply plug in to turn the pump
on
SAFETY PRECAUTIONS
- The pump should go through a residual current device (RCD, Circuit Breaker) with a rated residual operating current not to exceed 30mA. The pump should be connected and grounded
- Do not operate if the plug or cord are damaged or compromised in any
- Do not immerse the plug into water or any other
- In the following cases, please unplug the pump from power:
①When the water pump is not in use
②When installing or disassembling components
③Before cleaning the water pump
④When doing any work or maintenance on the waterfall or pond
- The water temperature should not exceed 95℉ (35℃). Do not immerse the pump beyond 6 feet in
- For safety reasons, any repair work should be done only by the manufacturer of the products or the authorized service
- Do not lift the pump by holding the power cord to avoid the cable connection coming loose inside the
- Avoid running the pump dry. Always make sure there is water running inside the pump when in operation. Whether the pump is submerged or not. If the pump is not submerged you should use a hose attachment and prime the
- If there is air in the pump it will not pump
- Do not allow children or inexperienced users operate the pump without
Pump Features:
- Ideal for water gardens, koi ponds and
- Designed for continuous
- High quality ceramic shaft and SIC bearing are designed to run efficiently and last a long
- No oil inside; safe for ponds with fish.
- Thermal overload
- Removable pre-filter prevents particles above 6mm from entering the
- The pump can be disassembled for
Specifications
Model| Rated voltage| Flow (GPH)| Max. Total Head
(Ft)| Input Current (A)| Inlet/Outlet (inch)
---|---|---|---|---|---
HMW-ARP2000| 120V 60Hz| 2100| 15| 0.95| Min.0.75”
– Max.1.5”
HMW-ARP3000| 120V 60Hz| 3000| 22| 1.6| Min.0.75” –
Max.1.5”
HMW-ARP5000| 120V 60Hz| 5000| 21| 2.45| Min.1” –
Max.2”
HMW-ARP8000| 120V 60Hz| 8000| 28| 5.2| Min.1” –
Max.2”
Placement
- When used as a submersible pump, the pump needs to be completely immersed in water; it needs to sit at least 6 inches below the surface to prevent inhalation of
- When used un-submersed the pump must have an un-obstructed continuous flow of water or else it will not pump sufficiently and may overheat. You can either place the pump lower in elevation than the surface of the water or prime it with a check
- When used un-submersed above elevation remove the pre-filter, screw on the adapter to the inlet and connect the water hose/pipe with a hose clamp. To prime the pump put a check valve on the water intake (where the hose/pipe meets the water source) then fill the pump with water from the top of the unit (outlet) completely with no air If you don’t fill the pump completely prior to turning it on water will not flow through. Attach another hose/pipe to the outlet adapter with a clamp and it’s ready to use.
Tips:
- Don’t let the pump freeze during the Bring it inside when it gets cold.
- The plug should be placed in a water-proof area and should be at least 6 feet away from the edge of the
- Keep the water clean to prolong the life of the
- The pump has a built-in thermal overload device which prevents the pump from If the unit overheats it will automatically shut off. Please allow the pump to cool down before restarting. If the unit continues to overheat it is usually caused by an obstruction.
ASSEMBLY INSTRUCTIONS
The pump comes assembled. To take it apart for cleaning start by sliding off the foot plate. The foot plate comes with 4 plastic feet that slide in an out of the base. Take off the pre-filter by pressing the two buttons in on one side. Unscrew the 4 screws connecting the pump body with the pump chamber. Pull the pump chamber apart from the pump body. Remove the seal O-ring and impeller/rotor.
To re-assemble the pump, put the rotor with impeller into the pump body, put on the sealing ring, and then install the pump chamber. Tighten the screws, clip the pre- filter back into place, and finally install the rear cover and suction feet.
Maintenance:
- Clean the pump regularly to ensure optimal
- When cleaning the blockage in the pump body, please disconnect the power supply first, and then disassemble it correctly according to the
- Use soft cloth to wipe the impeller and clean the pump with clear
- Remove the pump inlet to access the impeller. Turn around the rotor to check if it is broken or
- Check the pump inlet, outlet, and connecting pipe if it is blocked.
Troubleshooting:
- If the pump stops working potential solutions are check the power, let the pump cool down and clean the rotor of
- While setting up the pump unsubmerged refer to the placement section for proper
- If the pump stops pumping but it is still on, there could be residual air in the chamber, which would stop the water from pumping. The outlet or inlet pipe might be too
WARRANTY
This item covers 1 YEAR LIMITED WARRANTY from the original date of purchase. This warranty only applies to the original consumer purchaser and only to products used in normal use and service.
This warranty does not apply to products that are found to have been improperly installed, set-up, or used in any way not in accordance with the instruction supplied with product and failure of products as a result of an accidents, misuse, abuse, negligence, alternation, or faulty installation. This warranty shall not apply to the finish/scratching/tearing on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.If you have any questions, please visit our website and contact our customer service. www.homewellproducts.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>