aiwa ESBT-460 Quad Driver Hyperbass Wireless Neckband In Earphones Instruction Manual
- June 12, 2024
- Aiwa
Table of Contents
aiwa ESBT-460 Quad Driver Hyperbass Wireless Neckband In Earphones
Product Information
The product is a pair of earphones with built-in lithium-ion polymer battery. It features a quad driver hyperbass system and supports Bluetooth connectivity. The earphones are compatible with Siri and Google Voice Assistant and provide voice prompts for various functions.
Charging
- Insert a micro USB into the MICRO USB CHARGING PORT of the remote control.
- The LED indicator will turn red during charging.
- The red LED indicator will turn blue once the battery is fully charged.
Notes:
- Use a standard 5V USB Charger (not included) with the included USB Charging Cable.
- Fully charge the earphones before using it for the first time.
Phone Functions
Phone Calls
You can use the earphones to attend to your calls in handsfree mode. When you
receive an incoming call, the earphones will vibrate to alert you, so you will
never miss a call.
Voice Assistant (iOS / ANDROID)
Your earphones are compatible with Siri and Google Voice Assistant. To
activate your smartphone’s voice assistant:
- DOUBLE TAP the MULTIFUNCTION Button (Short Press it 2 times consecutively). The MICROPHONE of the earphone can be used to speak your command.
Voice Prompts
Your earphones have a built-in system that provides voice prompts for
various functions:
- You will hear “power on” when the earphone is powered on.
- You will hear “power off” when the earphone is powered off.
- You will hear “pairing” when the earphone enters pairing mode.
- You will hear “connected” when the earphone is paired.
- You will hear “low battery” when the earphone is in low power status.
- You will hear “max volume” when the volume is at the loudest level.
- You will hear “minimum volume” when the volume is at the lowest level.
Factory Reset
In case the earphones do not automatically go into pairing mode or during initial startup if the LED status indicator does not flash red and blue, please follow this procedure to reset the earphones:
- Power off the earphones by pressing and holding the multifunction button until the LED turns red and stays on for 3 seconds.
- Wait for 1 minute and then long press (press and hold) the multifunction button until the LED status indicator starts flashing red and blue continuously.
- The earphones have now been reset and are in pairing mode. You can now pair your mobile phone/tablet to the earphones using the normal procedure.
Product Usage Instructions
Power On/Off
-
Switching ON the Earphones
When the earphones are off, long press (press and hold) the multifunction button for about 2 seconds. The LED status indicator will light up, and the earphones will vibrate for about 3 seconds to indicate that the power is switched on. -
Switching OFF the Earphones
When the earphones are on, long press (press and hold) the multifunction button for about 3 seconds. The LED status indicator will go off, and the earphones will vibrate for about 3 seconds to indicate that the power is switched off.
Bluetooth Pairing
Connect your mobile phone or tablet or computer with the earphones using
Bluetooth wireless technology to listen to music or make phone calls. Begin by
pairing your phone/tablet/computer with the earphones. When you power on the
earphones for the first time, follow the steps below:
- Make sure the earphones are switched off.
- Switch on the earphones by long pressing (press and hold) the multifunction button for about 2 seconds.
- Put your mobile phone/tablet/computer in Bluetooth pairing mode.
- Search for Bluetooth devices on your mobile phone/tablet/computer and select the earphones from the list of available devices.
- If prompted, enter the pairing code or accept the pairing request on your mobile phone/tablet/computer.
- Once connected, you can play music or make phone calls using the earphones.
Music Playback
Playing Music from your Mobile Phone (or Tablet)
- Once your device and the earphone are paired, you can listen to music through Bluetooth.
- To play or pause the pl ayback, press the MULTI-FUNCTION button once.
- To move forward to the next track, press and hold the + button (LONG PRESS).
- To go back to the previous track, press and hold the – button (LONG PRESS)
Volume adjustment
- To increase the playback volume, press the + button (SHORT PRESS).
- To decrease the pl ayback volume, press the – button (SHORT PRESS)
- NOTES
- You can also control the volume from your smarlphone.
- When you reach maximum or minimum volume, there will be a voice prompt to notify you.
Playing Music from a MICRO-SD (or TF type) memory card
Insert a memory card into the slot on the Remote Controller as shown here.
Once the memory
card is inserted, the earphone will automatically start playing the first MP3
song which is stored on the card.
You can control VOLUME and Move to NEXT/PREVIOUS songs using the Remote
Controller buttons in the same way as mentioned above.
When a memory card is inserted, the Bluetooth functions are disabled. To re-
connect and use Bluetooth, simply remove the momory card from the slot. The
earphones will automatically
re-pair (re-connect) with your smartphone/tablet/computer.
Remote Controller
Specifications
- Bluetooth version: VS.O
- Bluetooth protocols: A2DP, SPP, AVRCP, HFP, HSP
- Wireless range: 10m (30 Ft.)
- Battery: 3.7V Lithium, 200mAh
- Charging time: 2 hours
- Standby Time: 180 hours
- Music Playback time: 15 hours
- Audio Frequency Response: 20Hz – 20,000Hz
- Sensitivity: 103土3 dB
- Impedance Per Driver: 32 Ohms
- Charging Port Type: Micro-USS Socket
- Charging Requirement: Standard USB SV, lA or higher (Charger not included)
All Rights
Reserved. All specifications are subject to change without prior notice. All
trademarks and trade names are the p,operty of their respective 吶ners. The
Bluetooth’word mark and logos are registered trademarks owned by Bluetootl1
SIG, Inc. and any use of such marks is under license.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>