BLUETTI ALP006-6d01A1 Smart Home Panel Instruction Manual

ALP006-6d01A1 Smart Home Panel
Instruction Manual

Sub Panel
Please read this manual before use and follow its guidance. Keep this manual for future reference.

User Manual
Please read this manual before use and follow its guidance. Keep this manual for future reference.

Introduction

Thank you for purchasing Sub Panel by BLUETTI.
Sub Panel is designed and developed by BLUETTI for household power storage intended to supply electrical power to home appliances, RVs, or remote locations where utility power is unavailable or in place of a utility due to a power outage. The Sub Panel is compatible with installations in the United States, Canada, Mexico, Japan, and other countries. The EP500(or AC300) + Sub Panel power system adopts environmentally friendly and safe lithium batteries, providing users with a longer and more stable backup power supply.
The user manual contains safety information to make you aware of hazards and risks associated with the Sub Panel and how to avoid them, and instructions about installation, operation, and maintenance. You must read these instructions thoroughly before starting or operating this equipment. Save this original instruction manual for future reference.
1.1 Features

• Indoor & Outdoor Installation.
• Compatible with BLUETTI AC300 and EP500/Pro.
• Support single and dual EP500/Pro or AC300 connected to generate power at 120V or 240V.
• Features inspection function. When the Sub Panel is required to be overhauled, the load on Sub Panel can be powered via the grid.
• Safety is ensured, and Sub Panel will prevent overloads.

1.2 Application
For users with Single EP500/Pro or AC300, please connect the load to SubPanel.(Chapter 3.1)
For users with Dual EP500/Pro or Dual AC300s, installation and enabling split phase function. (Chapter 3.2)
1.3 In The Box
The user must contact the dealer if the unit is defective.

| Unit| Quantity
---|---|---
A| Sub Panel| 1
B| User Manual| 1
C| Certification Card| 1

Figure 1.1 Package List
1.4 Quality Inspection
Check the unit before shipping.

Figure 1.2 Quality Test
1.5 Sign

| DANGER: The risk and severity of the shock depend on the voltage.
---|---
| WARNING： This May cause personal or equipment damage.

1.6 Safety
The user manual contains safety information to make you aware of hazards and risks associated with the Sub Panel and how to avoid them, and instructions about installation, operation, and maintenance.  It is essential to read and understand these instructions thoroughly before attempting to start or operate this equipment.

Installation

2.1 Preparation
2.1.1 Tool
Tools for installation of Sub Panel.

Figure 2.1.1 Tool Requirement
2.1.2 Wire
The wires connecting the home circuit to the Sub Panel are required as the chart below. The length and size of the cables are determined according to your needs and actual installation environment.

WARNING:
The AC cable should meet the requirements of National Electrical Standards.
2.2 Installation
The cable for connecting AC300 or EP500 series with Sub Panel contained in the package, please follow the instruction.

1. Take out the screw from the front cover of Sub Panel and remove it as Figure 2.2. 

2. Drill into the wall according to the size of Sub Panel.
   Type A – Mounting: 4PCS Expansion Screw for concrete wall, tapping screw for wooden.
   Type B – Hanging: 2PCS Expansion Screw for concrete wall, tapping screw for wooden.
   3) Mount the Sub Panel.

Mount the Sub Panel on the wall from the pre-bored holes.
2.3 Sub Panel Wiring
Please follow the next steps after you have properly mounted the Sub Panel.
DANGER:
Please use insulating tools during installation and maintenance.
DANGER:
Turn off all breakers before installation, and twist the main switch to “0”.
Confirm that your panel is no longer energized by utility power.
WARNING:
The AC cable should meet or exceed the requirements of National Electrical Standards.
2.3.1 Wiring to Grid

1. Determine the length of the connecting wire according to the distance from the Sub Panel to the Main Panel.
2. Connect the Line Wires, Neutral Wires to the circuit breaker`s wiring bar on Sub Panel.

2.3.2 Circuit of Load

1. Determine the length of the connecting wire according to the distance from the Sub Panel to the Main Panel.
2. Connect the Line Wire, Neutral Wire to the circuit breaker, bus bar on Sub Panel as Figure 2.5.

2.3.3 Wiring to BLUETTI Power Station
For better convenience, the connecting cables for EP500/Pro or AC300 (according to your order) are involved in the package of Sub Panel. Please turn to Chapter 3 for detailed installation information. Check the connection as (Circuit Diagram 1), put the front cover back.

Connection

Sub Panel supported Single or Dual BLUETTI Power Station connection. Compatible Model: EP500/Pro, AC300.
Please contact to the dealer whether you order the Sub Panel Version is compatible with your power station.
**DANGER:
Read the user manual before installation.
WARNING:
Ensure Sub Panel and the circuit is turned off.
3.1 Single Connection
For single EP500/Pro or AC300 power station.
Grid: 2-wire input from the grid at single-phase 100V or 120V is recommended.
The load capacity should exceed the Max Power of Input of the Power Station.
3.1.1 Single EP500**
Cable involved in the package of Sub Panel to connect with EP500.

Connection of single EP500 with Sub Panel
Cable involved in the package of Sub Panel to connect with EP500 solar power station.

WARNING:
The Input and Load circuits have to be connected to the same Line Wire.
3.1.2 Single EP500 Pro
Cable involved in the package of Sub Panel to connect with EP500Pro solar power station.

Connection of single EP500Pro with Sub Panel
WARNING:
The Input and Load circuit have to be connected to the same Line Wire.
3.1.3 Single AC300
Cable involved in the package of Sub Panel to connect with AC300 solar power station.

Connection of single EP500Pro with Sub Panel

WARNING:
The Input and Load circuits have to be connected to the same Line Wire.
3.2 Split Phase Connection System
For Dual EP500/Pro or Dual AC300 to enable Split Phase System.
Grid: 3-wire input from grid at single-phase 100V or 120V is recommended.
The load capacity should exceed the Grand Max Power of Input of Power Station.
3.2.1 Dual EP500
Cable involved in the package of Sub Panel to connect with Dual EP500 solar power station.

WARNING:
The Input and Load circuits have to be connected to the same Line Wire.
3.2.2 Dual EP500 Pro
Cable involved in the package of Sub Panel to connect with Dual EP500Pro solar power station.

WARNING:
The Input and Load circuits have to be connected to the same Line Wire.
3.2.3 Dual AC300
Cable involved in the package of Sub Panel to connect with Dual AC300
solar power station.
Cable involved in the package of Sub Panel to connect with Dual AC300 solar power station.

WARNING:
The Input and Load circuits have to be connected to the same Line Wire.

Operation

Sub Panel supports manual bypass conversion function for maintenance, When you want to remove the EP500/Pro, AC300 Power Station from the Sub Panel, please tweak the rotary switch on Sub Panel to “2” (Figure 4.3) to maintenance then disconnect the connecting cable on Power Station, the household load will be powered directly by the utility
power.
4.1 Pass-through Function
Rotary Switch Status:
“0”: Disconnect. Loads on Sub Panel are disconnected from both the utility power and Power Station. (Figure 4.1)
“1”: Connected. Sub Panel functions are all enabled. (Figure 4.2)
“2”: Grid power supply. The grid power supply status bit is directly supplied by the grid household load, which can complete the charging function for matching products.(Figure 4.3)

4.2 Grounding Method
FLOATING NEUTRAL: When Sub Panel is connecting with BLUETTI Power Station only(Disconnected with Main Panel): AC300, EP500, and EP500Pro, the N and PE Wire of the Input Port and Output Port of Power Station are not connected in Sub Panel directly, the distribution system`s neutral conductor will “float”, which means they are zoating neutral. BONDED NEUTRAL: Connecting the Sub Panel to BLUETTI Power Station will not switch the floating neutral to bonded neutral. If you want to convert the Sub Panel to bonded neutral, please connect the Sub Panel with Main Panel, or follow the instruction to connect the Neutral bus bar to PE.

Specifications

Specifications

Working Temperature| 0°C-45°C/32-113°F
Humidify| 10%-90%
Altitude| <2000m
Dimension (LWH)| 360140600mm/14.17S51*23.62in
Weight| 17KG/37.4Ibs

Maintenance

• Please follow the recommendations below for regular maintenance of the Sub Panel:
• Check the wiring of each part of the system regularly to whether the connection is stable.
• Cut off the power immediately if it is loose.
• Please tighten it after powering off. Regularly check the components for issues of vibration, abnormal sound or smell, etc.
• The clean exterior cover of Sub Panel regularly.
• Regularly check whether the wires of each part are integrated into Sub Panel, damaged wires should be replaced immediately.
• Please contact the dealer if the issues are not able to solve, a detailed record of the problems will help.

Copyright
BLUETTIPOWER.INC
Declaration Our company will not bear all responsibilities if the damage is caused by improper operation on the product. Our company shall not be liable for any damage caused by force majeure such as fire, typhoon, flood, earthquake or the user’s intentional negligence, misuse or other abnormal conditions. Some changes may not be explicitly noticed, such as appearance or specifications due to the exterior material and hardware improvement.
Version
A 2.1 Version.
Date: July 2021

Company: POWEROAK GmbH
Address: Lindwurmstr. 114, 80337 München Germany
Mail: logi@bluetti.de

Company: POWEROAK ENERGY UK CO., LTD
Address: Suite 108 Chase Business Center 39-41
Chase Side London United Kingdom N14 5BP
Mail:poweroak.eu@bluetti.com
P/N:17.0303.0391-01A1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>