KARCHER HD 5/11 C High-Pressure Washer Instruction Manual

KARCHER HD 5/11 C High-Pressure Washer Instruction Manual

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

Keep both books for future reference or for future owners.

Intended use

Use this high-pressure cleaner only for the following types of work:

• leaning with the low-pressure jet and detergent (e.g. machines, vehicles, structures, tools)
• Cleaning with the high-pressure jet without detergent (e.g. façades, terraces, garden machines) We recommend using a rotary nozzle as a special accessory for stubborn soiling.

A rotary nozzle is included in the scope of delivery of the “Plus” variant.

Water supply limit values

ATTENTION

Dirty water
Premature wear and tear or deposits in the device Supply the device using only clean water, or recycled water that does not exceed the specified limit values. The following limit values apply to the water supply:

• pH value: 6.5-9.5
• Electrical conductivity: Conductivity of fresh water + 1200 µS/cm, maximum conductivity 2000 µS/cm
•  Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l
• Filterable particles: < 50 mg/l, no abrasive substances
• Hydrocarbons: < 20 mg/l
• Chloride: < 300 mg/l
• Sulphate: < 240 mg/l
• Calcium: < 200 mg/l
• Total hardness: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO3/l)
• Iron: < 0.5 mg/l
• Manganese: < 0.05 mg/l
• Copper: < 2 mg/l
• Active chloride: < 0.3 mg/l
• Free of unpleasant odours

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.

Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH

Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and

safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Safety instructions

• It is essential that you read the safety instructions 5.951-949.0 before initial startup.
• Observe the national regulations for liquid jet cleaners.
• Observe the national accident prevention regulations. Liquid jet cleaners must be tested regularly. The test result must be recorded in writing.
• Do not modify the device or accessories.

Symbols on the device
The device may not be connected to the public drinking water network. The high-pressure jet must not be directed at persons, animals, live electrical equipment or at the device itself. Protect the device from frost. Safety devices

CAUTION
Missing or modified safety devices Safety devices are provided for your own protection. Never modify or bypass safety devices. The safety devices are set and sealed by the manufacturer. Adjustments are performed only by customer service.

Pressure switch

When the trigger on the high-pressure gun is released, the pressure switch switches off the high-pressure pump and the high-pressure jet stops. The pump switches on again when the trigger is pulled.

Device description

Overview of the unit
See graphics page

1. Hubcap
2. Nozzle holder
3. Skid
4. Type plate
5. Nozzle storage for triple nozzle
6. Transport retainer for surface cleaner
7. Push handle lock
8. Push handle, bottom (pushed in)
9. Push handle, top (pulled out)
10. High-pressure nozzle
11. High-pressure nozzle marking
12. EASY!Lock spray lance
13. EASY!Force high-pressure gun
14. Safety latch
15. Trigger
16. Safety lever
17. EASY!Lock high-pressure hose
18. Hose storage compartment
19. Cable clips
20. Spray lance holder without a clamp
21. Rubber band (not in devices with a hose reel)
22. Nozzle storage compartment for rotary nozzle (rotary nozzle only included in the scope of delivery of the “Plus” variant)
23. Spray lance holder with a clamp for transport
24. Power switch
25. Handle
26. EASY!Lock high-pressure connection
27. Handle
28. Water connection
29. Detergent suction hose with filter and detergent dosing unit
30. sieve
31. Hose spout
32. Union nut
33. Crank
34. Hose reel

Colour coding

• Control elements for the cleaning process are yellow.
• Control elements for maintenance and servicing are light grey

Installation

Fastening the hubcaps

• Fasten the hubcaps.

Installing accessories

Note
The EASY!Lock system connects components quickly and safely via a single turn of the quick-release thread.

1. Fit the high-pressure nozzle onto the spray lance with the marking facing upwards.

2. Tighten the high-pressure nozzle hand-tight (EASY!Lock).

3. Connect the spray lance to the high-pressure gun and hand-tighten (EASY!Lock).
   

4. Release the push handle lock.

5. Pull the push handle out to the end position. For devices without a hose reel:

6. Connect the high-pressure hose to the high-pressure gun and high-pressure connection of the device and tighten hand-tight (EASY!Lock). For devices with a hose reel:

7. Lay the high-pressure hose on the ground in a straight line.

8. Insert the crank into the hose reel shaft and latch into position.

9. Turn the crank clockwise and wind the high-pressure hose onto the hose reel in evenly distributed layers.

10. Connect the high-pressure hose to the high-pressure gun and hand-tighten (EASY!Lock

Electrical connection

DANGER
Failure to disconnect the mains

Risk of injury from electric shock

Use a plug to connect the device to the mains grid. Permanent connection to the mains grid is prohibited. The plug is used for disconnection from the mains.

1. Unwind the mains cable and place on the ground.
2. Plug the mains plug into the socket.

Water connection

Connection to a water line

WARNING
Return flow of dirty water into the drinking water network

Health risk
Observe the regulations of your water supply company. According to applicable regulations, the device must never be used with the drinking water network without a system separator. Use a system separator from KÄRCHER or a system separator as per EN 12729

Type BA. Water that has flowed through a system separator is classified as undrinkable. Always connect the
system separator to the water supply and never directly
to the water connection on the device.

1. Check the supply pressure, supply temperature and supply volume of the water supply (see chapter Technical data).
2. Connect the system separator to the water connection of the device using a water supply hose (for the requirements placed on the water supply hose see chapter Technical data).
3. Open the water inlet.

Suck water from the container

1. Screw the suction hose with filter onto the water connection (for the order number see chapter Technical data).
2. Vent the device (see chapter Vent the device).

Vent the device

1. Unscrew the high-pressure nozzle from the spray lance.
2. Allow the device to run until the escaping water is free of air bubbles.
3. In the case of venting problems, allow the device to run for 10 seconds and then switch it off. Repeat the procedure several times.
4. Switch off the device.
5. Screw the high-pressure nozzle onto the spray lance.

Operation

DANGER
High-pressure water jet

Danger of injury
Never fasten the trigger and safety lever in the actuated position. Do not use the high-pressure gun when the safety lever is damaged.

Push the safety latch of the high-pressure gun forwards every time before starting work with the device. Hold the high-pressure gun and spray lance with both hands.

WARNING
Defective device and accessories, defective supply lines and connections Danger of injury The device may only be operated when in a correct operating condition.

Opening/closing the high-pressure gun

1.  Actuate the safety lever and trigger. The high-pressure gun opens.
2. Release the safety lever and trigger. The high-pressure gun closes.

High-pressure operation

The device can be operated in a standing or lying position.

Note
The device is equipped with a pressure switch. The motor only starts up when the high-pressure gun is open.

1. For devices with a hose reel: Completely unroll the high-pressure hose from the hose reel.
2. Set the power switch to the “I/ON” position.
3. Push the safety latch of the high-pressure gun to the rear. The high-pressure gun is unlocked.
4. Open the high-pressure gun.

Selecting the spray type

1. Close the high-pressure gun.
2. Turn the casing of the nozzle until the desired symbol lines up with the marking.

| High-pressure round stream (0°) for espe- cially stubborn soiling
---|---
| Low-pressure flat stream (CHEM) for oper- ating with detergent or cleaning at low pres- sure
| High pressure flat stream (25°) for large soiled areas

Operation with detergent

DANGER
Residual high pressure in the device Danger of injury Switch off the device prior to changing nozzles. Actuate the high-pressure gun until the device is completely depressurised.

WARNING
Incorrect handling of detergents Health risk Adhere to the safety instructions stated on the detergent packaging.

ATTENTION
Unsuitable detergents Damage to the device and the objects to be cleaned Use only detergents approved by KÄRCHER. Observe the dosing recommendations and notes provided with the detergent. Use detergents sparingly to help conserve the environment.

Note
KÄRCHER detergents ensure fault-free operation. Ask us for a consultation, request our catalogue or our detergent information sheets.

1. Pull out the detergent suction hose.
2. Adjust the detergent solution suction volume at the detergent filter.
3. Hang the detergent suction hose in a container with detergent.
4. Set the nozzle to the “CHEM” position.
5. Start up the high-pressure cleaner

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.

After operation with detergent

1. Adjust the suction volume at the detergent filter to the maximum volume.
2. Immerse the filter in clear water.
3. Start the device and rinse clear for one minute.

Interrupting operation

1. Close the high-pressure gun. The device switches off.
2. Push the safety latch forwards. The high-pressure gun is secured.

Continuing operation

1. Push the safety latch backwards. The high-pressure gun is unlocked.
2. Open the high-pressure gun. The device switches on.

Finishing operation

1. Close the water inlet.
2. Open the high-pressure gun.
3. Set the power switch to “I/ON” and allow the device to run for 5-10 seconds.
4. Close the high-pressure gun.
5. Set the power switch to “0/OFF”.
6. Pull the mains plug out of the socket only when your hands are dry.
7. Remove the water inlet.
8. Open the high-pressure gun until the device is completely depressurised.
9. Push the safety latch forwards. The high-pressure gun is secured.

Transport

CAUTION
Failure to observe the weight Risk of injury and damage Be aware of the weight of the device during transport and storage.

ATTENTION
Improper transportation Risk of damage Protect the trigger of the high- pressure gun from damage.

• Transporting the device in a vehicle: Secure the device in accordance with the respectively applicable guidelines to prevent it from slipping or overturning.
• Transporting the device over longer distances: Pull the device behind you via the push handle.
• Transporting the device over stairs: Pull the device step by step. The skids protect the casing from damage.
• Carrying the device: Carry the device by the handles only.

Transport retainer for surface cleaner

1. Plug the connection union of the surface cleaner onto the transport holder of the high-pressure cleaner.
2. Screw on the union nut by approximately 1 turn

Crane transport

DANGER
Improper crane transport Risk of injury from a falling device or falling objects Observe the local regulations for accident prevention and the safety instructions. The device may only be transported with a crane by persons instructed in the operation of the crane. Check the lifting gear for damage before each crane transport. Check the handle for damage before each crane transport.

Lift the device only by the handle.

Do not use an slinging chains. Secure the lifting gear against unintentional unhooking of the load.

Remove the spray lance with high-pressure gun, nozzles, surface cleaner and other loose objects before transporting by crane.

Do not transport any objects on the device during the lifting operation. Do not stand under the suspended load. Ensure that no persons are in the hazard zones of the crane. Do not leave the device handing unattended on the crane.

1. Attach the lifting gear to the handle on the device.
   

Storage

CAUTION
Failure to observe the weight Risk of injury and damage Be aware of the weight of the device during transport and storage.

Store the device indoors only

Storing the device

1. Fit the spray lance with high-pressure gun into the nozzle holder and latch into position in the spray lance holder.

2. Roll up the mains cable and hang it over the cable holders.

3. Fasten the plug with the clip provided. For devices with a hose reel:

4. Wind the high-pressure hose onto the hose reel and fold over the crank handle. For devices without a hose reel:

5. Storing the high-pressure hose:
   a Wind up the high-pressure hose.
   b Hang the high-pressure hose over the hose storage compartment.
   c Secure the high-pressure hose with the rubber band.

6. Press the push handle lock and slide in the push handle.

Frost protection

ATTENTION
Frost
Destruction of the device through freezing water Drain all water from the device. Store the device in a frost-free location.

If frost-free storage is not possible:

1. Drain the water.

2. Pump commonly available anti-freeze through the device.
   Note
   Use commonly available, Glycol-based vehicle antifreeze. Observe the handling instructions of the antifreeze manufacturer.

3. Allow the device for run for a maximum of 1 minute until the pump and lines are empty

Care and service

DANGER
Inadvertently starting up device Risk of injury, electric shock Switch off the device immediately and unplug the mains plug before performing work.

Note
Old oil may only be disposed of at designated collection points. Please dispose of any old oil at these locations. Polluting the environment with old oil is punishable by law.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek advice on this.

Maintenance intervals

Each time before use

• Check the mains cable for damage. Have a damaged cable replaced immediately by the authorised Customer Service or a qualified electrician.
• Check the high-pressure hose for damage. Immediately replace a damaged high-pressure hose.
• Check the device for leaks. 3 drops of water per minute are permissible. Contact Customer Service in the case of more serious leaks.

Weekly

• Empty and clean the sieve in the water connection (see chapter Clean the sieve in the water connection).
• Clean the filter on the detergent suction hose.

Every 500 operating hours, at least annually

• Have the device serviced by Customer Service.

Maintenance work

Clean the sieve in the water connection

1. Unscrew the union nut.

2. Remove the hose union.

3. Remove the sieve.

4. Externally clean and rinse the sieve.

5. Insert the sieve.
   Note
   Align the hex-head of the hose union to the connection on the device.

6. Attach the hose union and tighten with the union nut.

Troubleshooting guide

DANGER
Inadvertently starting up device, touching live components Risk of injury, electric shock Switch off the device before performing any work on the device.

Remove the mains plug.
Have all checks and work on electrical parts performed by a qualified electrician.
In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service.

The device cannot be started

1. Check the mains cable for damage.

2. Check the mains voltage.

3. If the device overheats:
   a Set the power switch to “0/OFF”.
   b Allow the device to cool for at least 15 minutes.
   c Set the power switch to the “I/ON” position.

4. Contact Customer Service in the case of electrical faults.

Device does not reach required pressure

1. Set the nozzle to high-pressure.
2. Vent the device (see chapter Vent the device).
3. Empty and clean the sieve in the water connection (see chapter Clean the sieve in the water connection).
4. Check the water supply volume (for the necessary volume see chapter Technical data).
5. Clean the nozzle and replace if necessary.
6. Contact Customer Service if necessary.

The pump is leaking.

Up to 3 drops of water per minute are permissible.

• In case of more serious leaks, have the device checked by Customer Service.

The pump knocks

1. Check the water supply line for leaks.
2. Check the detergent suction line for leaks.
3. Adjust the suction volume at the detergent filter to the minimum volume.
4. Vent the device (see chapter Vent the device).
5. Contact Customer Service if necessary.

The detergent mixture ratio is too weak

1. Set the nozzle to “CHEM”.
2. Increase the suction volume at the detergent filter.
3. Open or check/clean the detergent suction hose with filter.
4. Contact Customer Service if necessary.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Technical data

Country variant| | | | | | | |
---|---|---|---|---|---|---|---|---
Country| | AU| EU| GB              CH| AU| KAP| SA|
Electrical connection| | | | | | | |
Voltage| V| 240| 230| 230-240 230| 240| 220| 220|
Phase| ~| 1| 1| 1                  1| 1| 1| 1|
Frequency| Hz| 50| 50| 50               50| 50| 60| 60|
Connection output| kW| 2,1| 2,5| 2,5              2,2| 2,2| 2,4| 2,4|
Degree of protection| | IPX5| IPX5| IPX5          IPX5| IPX5| IPX5| IPX5|
Power protection (slow-blowing)| A| 10| 16| 13| 10| 10| 15| 13|
Extension cable, 30 m| mm2| 2,5| 2,5| 2,5| 2,5| 2,5| 2,5| 2,5|
Water connection| | | | | | | | |
Feed pressure (max.)| MPa| 1| 1| 1| 1| 1| 1| 1|
Input temperature (max.)| °C| 60| 60| 60| 60| 60| 60| 60|
Input amount (min.)| l/min| 12| 12| 12| 12| 12| 12| 12|
Suction height (max.)| m| 0,5| 0,5| 0,5| 0,5| 0,5| 0,5| 0,5|
Minimum water supply hose length| m| 7,5| 7,5| 7,5| 7,5| 7,5| 7,5| 7,5|
Minimum water supply hose diameter| in| 1/2| 1/2| 1/2| 1/2| 1/2| 1/2| 1/2|
Suction hose with filter order number| | 2.643-| 2.643-| 2.643-| 2.643-| 2.643-| 2.643-| 2.643-|
| | 100.0| 100.0| 100.0| 100.0| 100.0| 100.0| 100.0|
Device performance data| | | | | | | | |
Nozzle size of standard nozzle| | 038| 035| 035| 038| 038| 036| 036|
Operating pressure| MPa| 11| 12| 12| 11,5| 11,5| 12| 12|
Operating pressure (max.)| MPa| 17,1| 17,5| 17,5| 17,1| 17,1| 18| 18|
Water flow rate| l/min| 8,3| 8,3| 8,3| 8,3| 8,3| 8,3| 8,3|
Detergent flow rate| l/h| 0-25| 0-25| 0-25| 0-25| 0-25| 0-25| 0-25|
High-pressure gun recoil force| N| 21,3| 21,3| 21,3| 21,3| 21,3| 21,3| 21,3|
Dimensions and weights| | | | | | | | |
Typical operating weight (CX)| kg| 24,2 (-)| 23,7| 23,7| 23,7| 24,2| 25,2 (-)| 25,2 (-)|
| | | (26)| (26)| (26)| (26,4)| | |
Length| mm| 380| 380| 380| 380| 380| 380| 380|
Width (CX)| mm| 360 (-)| 360| 360| 360| 360| 360 (-)| 360 (-)|
| | | (370)| (370)| (370)| (370)| | |
Height| mm| 930| 930| 930| 930| 930| 930| 930|
Determined values in acc. with EN 60335-2-79|
Hand-arm vibration value| m/s2| 3,6              3,6| 3,6| 3,6| 3,6| 4,2| 4,2|
Uncertainty K| m/s2| 0,9              0,9| 0,9| 0,9| 0,9| 0,9| 0,9|
Sound pressure level LpA (CX)| dB(A)| 72 (-)          72 (75)| 72 (75)| 72 (75)| 72 (75)| 74 (-)| 74 (-)|
Uncertainty KpA| dB(A)| 3                  3| 3| 3| 3| 3| 3|
Sound power level LWA +| dB(A)| 88 (-)          88 (92)| 88 (92)| 88 (92)| 88 (92)| 90 (-)| 90 (-)|
Country variant| | | | | | | |
Country| | EU              EU| EU| KAP| EU| AR| GB|
Electrical connection| | | | | | | |
Voltage| V| 230             230| 230| 220| 230| 220| 230-240|
Phase| ~| 1                  1| 1| 1| 1| 1| 1|
Frequency| Hz| 50               50| 50| 60| 50| 50| 50|
Connection output| kW| 2,6              2,8| 3,0| 3,0| 2,9| 2,9| 2,9|
Degree of protection| | IPX5          IPX5| IPX5| IPX5| IPX5| IPX5| IPX5|
Power protection (slow-blowing)| A| 16               16| 16| 15| 16| 16| 13|
Extension cable, 30 m| mm2| 2,5              2,5| 2,5| 2,5| 2,5| 2,5| 2,5|
Water connection| | | | | | | |
Feed pressure (max.)| MPa| 1                  1| 1| 1| 1| 1| 1|
Input temperature (max.)| °C| 60               60| 60| 60| 60| 60| 60|
Input amount (min.)| l/min| 12| 12| 12| 12| 13| 13| 13|
Suction height (max.)| m| 0,5| 0,5| 0,5| 0,5| 0,5| 0,5| 0,5|
Minimum water supply hose length| m| 7,5| 7,5| 7,5| 7,5| 7,5| 7,5| 7,5|
Minimum water supply hose diameter| in| 1/2| 1/2| 1/2| 1/2| 1/2| 1/2| 1/2|
Suction hose with filter order number| | 2.643-| 2.643-| 2.643-| 2.643-| 2.643-| 2.643-| 2.643-|
| | 100.0| 100.0| 100.0| 100.0| 100.0| 100.0| 100.0|
Device performance data| | | | | | | | |
Nozzle size of standard nozzle| | 034| 032| 027| 030| 038| 038| 038|
Operating pressure| MPa| 13| 15| 17| 16,5| 13| 13| 13|
Operating pressure (max.)| MPa| 17,5| 20| 20| 20| 19| 19| 19|
Water flow rate| l/min| 8,3| 8,3| 8,1| 8,0| 9,8| 9,8| 9,8|
Detergent flow rate| l/h| 0-25| 0-25| 0-25| 0-25| 0-25| 0-25| 0-25|
High-pressure gun recoil force| N| 22,2| 23,8| 25,4| 25,4| 26,6| 26,6| 26,6|
Dimensions and weights| | | | | | | | |
Typical operating weight (CX)| kg| 23,7| 25,2| 25,2| 25,2| 25,2| 25,2 (-)| 25,2|
| | (26)| (27,5)| (27,5)| (27,5)| (27,5)| | (27,5)|
Length| mm| 380| 380| 380| 380| 380| 380| 380|
Width (CX)| mm| 360| 360| 360| 360| 360| 360 (-)| 360|
| | (370)| (370)| (370)| (370)| (370)| | (370)|
Height| mm| 930| 930| 930| 930| 930| 930| 930|
Determined values in acc. with EN 60335-2-79|
Hand-arm vibration value| m/s2| 3,6| 2,4| 2,4| 2,4| 4,1| 4,1| 4,1|
Uncertainty K| m/s2| 0,9| 0,7| 0,7| 0,7| 0,9| 0,9| 0,9|
Sound pressure level LpA (CX)| dB(A)| 72 (75)| 72 (74)| 72 (75)| 75 (75)| 72 (75)| 72 (-)| 72 (75)|
Uncertainty KpA| dB(A)| 3| 3| 3| 3| 3| 3| 3|
Sound power level LWA +| dB(A)| 88 (92)| 88 (90)| 88 (92)| 91 (91)| 88 (92)| 88 (-)| 88 (92)|
Electrical connection| | | | | | | | |
Voltage| V| 220| 220| | | | | |
Phase| ~| 1| 1| | | | | |
Frequency| Hz| 60| 60| | | | | |
Connection output| kW| 2,9| 2,8| | | | | |
Degree of protection| | IPX5| IPX5| | | | | |
Power protection (slow-blowing)| A| 15| 13| | | | | |
Extension cable, 30 m| mm2| 2,5| 2,5| | | | | |
Water connection| | | | | | | | |
Feed pressure (max.)| MPa| 1| 1| | | | | |
Input temperature (max.)| °C| 60| 60| | | | | |
Input amount (min.)| l/min| 13| 13| | | | | |
Suction height (max.)| m| 0,5| 0,5| | | | | |
Minimum water supply hose length| m| 7,5| 7,5| | | | | |
Minimum water supply hose diameter| in| 1/2| 1/2| | | | | |
Suction hose with filter order number| | 2.643-| 2.643-| | | | | |
| | 100.0| 100.0| | | | | |
Operating pressure (max.)| MPa| 18| 18|
Water flow rate| l/min| 10,0| 10,0|
Detergent flow rate| l/h| 0-25| 0-25|
High-pressure gun recoil force| N| 26,6| 26,6|
Dimensions and weights| | | |
Typical operating weight (CX)| kg| 25,2 (-)| 25,2 (-)|
Length| mm| 380| 380|
Width (CX)| mm| 360 (-)| 360 (-)|
Height| mm| 930| 930|
Determined values in acc. with EN 60335-2-79|
Hand-arm vibration value| m/s2| 3,7| 3,7|
Uncertainty K| m/s2| 0,9| 0,9|
Sound pressure level LpA (CX)| dB(A)| 73 (-)| 73 (-)|
Uncertainty KpA| dB(A)| 3| 3|
Sound power level LWA +| dB(A)| 89 (-)| 89 (-)|
Subject to technical modifications.| | | HD 5/15 CX|

Subject to technical modifications.

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any
changes made to the machine that are not approved by us.

Product: High-pressure cleaner
Type: 1.520-xxx

Currently applicable EU Directives

• 2006/42/EC (+2009/127/EC)
• 2014/30/EU
• 2000/14/EC

Harmonised standards used

• EN 60335-1
• EN 60335-2-79
• EN 55014-1: 2006+A1: 2009+A2: 2011
• EN 55014-2: 2015
• EN 62233: 2008
• EN 61000-3-2: 2014
• EN 61000-3-3: 2008
• HD 5/12 C, HD 5/12 CX, HD 5/13 C, HD 5/13 CX
• EN 61000-3-11: 2000
• HD 5/15 C, HD 5/15 CX, HD 5/17 C, HD 5/17 CX, HD 6/ 13 C, HD 6/13 CX

Applied conformity evaluation method
2000/14/EG: Appendix V
Sound power level dB(A)

HD 5/12 C, HD 5/13 C, HD 5/15 C, HD 5/17 C, HD 6/13 C
Measured: 86
Guaranteed: 88

HD 5/12 CX, HD 5/13 CX, HD 5/17 CX, HD 6/13 CX
Measured: 89
Guaranteed: 92

HD 5/15 CX
Measured: 87
Guaranteed: 90
The signatories act on behalf of and with the authority of the company management.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Documentation supervisor: S. Reiser
Alfred-Kärcher-Str. 28 – 40 71364 Winnenden (Germany)

Ph.: +49 7195 14-0
Fax: +49 7195 14-2212

Winnenden, 2019/05/01

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>