PROAIM DL-CLBS-01 Video Camera Platform Dolly Instruction Manual

: June 12, 2024
: PROAIM

Table of Contents

PROAIM DL-CLBS-01 Video Camera Platform Dolly
What’s In The Box
- Columbus Dolly Setup
Assembling Push Bar Handel
- Assembling Euro Adapter Plate
- Assembling Flexino Bazooka Set
Assembling 75mm Fluid Head
Cranked Telescopic Bazooka Setup

PROAIM DL-CLBS-01 Video Camera Platform Dolly

What’s In The Box

Please inspect the contents of your shipped package to ensure you have received everything that is listed below.

Push Bar Handle
Columbus Platform Dolly
T-Type Allen Key (Size: 6mm)

All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted by the applicable copyright statutes or in writing by the Publisher.

Columbus Dolly Setup

Place the Columbus Dolly on the Velvet Steel Track (Not Included), as shown in the image.
Now place the Columbus Dolly onto the Velvet Steel Track (Not Included). Make sure all wheels are aligned correctly on the track and dolly runs smoothly.

NOTE: It smoothly maneuvers on a curved or conventional track with equipped 4 x 4 skateboard wheels that assure flawless and smooth mobility without drift, noise, or excessive rolling resistance. Adding to that, the wheel has a push and pull mechanism that allows the wheels to be readily attached and removed from the dolly at any given moment.

Assembling Push Bar Handel

Attach the push Bar Handle to the side corner of the Columbus Dolly by tightening both the knobs to properly secure it.
The push bar handle is properly attached to the Columbus Dolly.

NOTE: The push-bar handle offers smooth dolly operations; it can be attached to any four corners of the platform of the dolly.

Assembling Euro Adapter Plate

Place the Adapter Plate by matching it (Not Included) with the center thread hole of the Dolly, and then insert the bolts.
After inserting the bolts in the Euro Adapter Plate (Not Included), tighten the bolts with the help of the Allen Key.

Assembling Flexino Bazooka Set

Loosen the Knob of the Flexino Bazooka (Not Included) and mount it on the Euro Adapter Plate (Not Included), as shown in the image.
After properly mounting the Flexino Bazooka (Not Included) onto the Euro Adapter Plate (Not Included), securely re-tighten the assembly with the ratchet knob.
Loosen the ratchet knob of Bowl Riser Adapter (Not Included), and then attach it to the top of the Flexino Bazooka (Not Included).
Then secure the assembly using the ratchet knob.

Assembling 75mm Fluid Head

Remove the knob of 75mm Bowl Fluid Head (Not Included) and mount it onto the Bowl Riser Adapter (Not Included).
Then, properly tighten the knob of the Fluid Head (Not Included) from bottom.
Pull & release the knob of the Fluid Head, and then remove the plate. Now, attach the plate to the bottom of the camera (Not Included).
Secure the assembly using the screwdriver and mount the camera (Not Included) on the Fluid Head, as shown in the image.
Now, pull the knob of the Fluid Head and properly tighten it to secure the camera (Not Included).

Cranked Telescopic Bazooka Setup

Loosen the knob of the Cranked Bazooka (Not Included) and mount it on the Euro Adapter Plate (Not Included), as shown in the image.

NOTE: Multiple 3/8-16 threaded holes on the dolly platform offer incredible mounting flexibility for compatible gear and accessories. That’s why you can change the position of euro adapter and put it on the side.

Product Usage Instructions

Inspect the contents of the package to ensure all components are present.
Place the Columbus Dolly on a Velvet Steel Track and ensure all wheels are aligned correctly for smooth movement.
Attach the push Bar Handle to any of the four corners of the Columbus Dolly for smooth operations.
Attach the Euro Adapter Plate to the center thread hole of the Dolly and tighten using bolts and an Allen Key.
Mount the Flexino Bazooka onto the Euro Adapter Plate and securely tighten using the ratchet knob.
Attach the Bowl Riser Adapter to the top of the Flexino Bazooka and secure using the ratchet knob.
Mount the 75mm Bowl Fluid Head onto the Bowl Riser Adapter and secure using the knob from the bottom.
Attach the camera to the Fluid Head using the plate and screwdriver, and then secure it using the knob on top of the Fluid Head.
Mount the Cranked Bazooka onto the Euro Adapter Plate for incredible mounting flexibility.

What’s In The Box

Please inspect the contents of your shipped package to ensure you have received everything that is listed below. PROAIM DL-CLBS-01 Video Camera
Platform Dolly FIG-1

Columbus Dolly Setup

Place the Columbus Dolly on the Velvet Steel Track (Not Included), as shown in the image.
Now place the Columbus Dolly onto the Velvet Steel Track (Not Included). Make sure all wheels are aligned correctly on the track and dolly runs smoothly.
NOTE: It smoothly maneuvers on a curved or conventional track with equipped 4 x 4 skateboard wheels that assure flawless and smooth mobility without drift, noise, or excessive rolling resistance.
NOTE: Adding to that, the wheel has a push and pull mechanism that allows the wheels to be readily attached and removed from the dolly at any given moment.

Assembling Push Bar Handel

Now, attach the push Bar Handle to the side corner of the Columbus Dolly by tightening both the knobs to properly secure it.
The push bar handle is properly attached to the Columbus Dolly.
NOTE: The push-bar handle offers smooth dolly operations; it can be attached to any four corners of the platform of the dolly.

Assembling Euro Adapter Plate

Place the Adapter Plate by matching it (Not Included) with the center thread hole of the Dolly, and then insert the bolts.
After inserting the bolts in the Euro Adapter Plate (Not Included), tighten the bolts with the help of the Allen Key.

Assembling Flexino Bazooka Set

Loosen the Knob of the Flexino Bazooka (Not Included) and mount it on the Euro Adapter Plate (Not Included), as shown in the image.
After properly mounting the Flexino Bazooka (Not Included) onto the Euro Adapter Plate (Not Included), securely re-tighten the assembly with the ratchet knob.
Loosen the ratchet knob of Bowl Riser Adapter (Not Included), and then attach it to the top of the Flexino Bazooka (Not Included).
Then secure the assembly using the ratchet knob.

Assembling 75mm Fluid Head

Remove the knob of 75mm Bowl Fluid Head (Not Included) and mount it onto the Bowl Riser Adapter (Not Included).
Then, properly tighten the knob of the Fluid Head (Not Included) from bottom.
Pull & release the knob of the Fluid Head, and then remove the plate. Now, attach the plate to the bottom of the camera (Not Included).
Secure the assembly using the screwdriver and mount the camera (Not Included) on the Fluid Head, as shown in the image.
Now, pull the knob of the Fluid Head and properly tighten it to secure the camera (Not Included).

Cranked Telescopic Bazooka Setup

Loosen the knob of the Cranked Bazooka (Not Included) and mount it on the Euro Adapter Plate (Not Included), as shown in the image.
NOTE: Multiple 3/8”-16 threaded holes on the dolly platform offer incredible mounting flexibility for compatible gear and accessories. That’s why you can change the position of euro adapter and put it on the side.
After properly mounting the Cranked Bazooka (Not Included) on the Euro Adapter Plate (Not Included), secure the Bazooka with the ratchet knob by tightening it.

Assembling Offset Euro (100mm Bowl Adapter)

Loosen the ratchet knob of the offset (100mm Bowl Adapter) (Not Included) and mount it on the Cranked Bazooka (Not Included), as shown in the image.
After properly mounting the offset (Not Included) on the cranked Bazooka (Not Included), secure it by tightening the ratchet knob.
Mount the 100mm bowl Fluid Head (Not Included) on the offset (Not Included).

Assembling of Turnstile mount

Place the Turnstile at the center of the Columbus Dolly by matching the threads (Not Included).
Then, properly secure the Turnstile (Not Included) on the Columbus Dolly with the help of bolts.
Properly lock the assembly with the help of the provided locking brake of the Turnstile (Not Included).

Assembling of Seat arm

Loosen the knob of the seat arm (Not Included), and then place it on the baby pin of the Turnstile (Not Included).
Properly secure it by tightening the knob of the seat arm (Not Included).
Loosen the second knob (top seat mounting) of seat arm (Not Included) and insert the seat (Not Included) into the seat hole by matching the threads.
Now, properly secure the seat by tightening the seat arm (Not Included) knob.
Compatibility :
Compatible with a Euro-adapter or turnstile mount, it lets you attach a bazooka, risers, seats, other compatible gears, and accessories.

YOUR PROAIM COLUMBUS VIDEO CAMERA PLATFORM DOLLY ALL DRESSED UP AND READY TO GO!

Warranty

We offer one year warranty for our products from date of purchase. Within this period of time, we will repair it without charge for labor or parts. Warranty doesn’t cover transportation costs nor does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspection and evaluation by us.

Liability: We are not liable for damage caused by products that we do not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissatisfaction, please Contact us immediately and we promise our utmost support and care until you use our product.