UNI-T UTi120S Thermal Imaging User Manual
- June 4, 2024
- UNI-T
Table of Contents
UTi120S Thermal Imaging
User Manual
UTi120S
Professional Thermal Imager User Manual
Preface
Thank you for purchasing the new U111205 thermal imager. In order to use this
product safely and correctly. please read this manual thoroughly. especially
the Safety Instructions part.
After reading this manual, it is recommended to keep the manual at an easily
accessible place, preferably close to the device, for future reference.
Limited Warranty and Liability
Uni-Trend guarantees that the product is free from any defect in material and
workmanship within one year from the purchase date. This warranty does not
apply to damages caused by accident, negligence, misuse, modification,
contamination or improper handling. The dealer shall not be entitled to give
any other warranty on behalf of UM-Trend. If you need warranty service within
the warranty period, please contact your seller directly.
Uni-Trend will not be responsible for any special. indirect, incidental or
subsequent damage or loss caused by using this device.
Specifications
| Sensor | Uncooled infrared focal plane thermal imaging sensor |
|---|---|
| Pixel size | 17 pm |
| Infrared spectrum bandwidth | 8-14pm |
| Thermal imaging pixels | 10800 (120’90) |
| Thermal imaging sensitivity | <60mK |
| Field of view (FOV) | 50°(H) x 38°(V) |
| Spatial resolution (IFOV) | 7.6 mrad |
| Rate | 25Hz |
| Minimum imaging distance | 0.1m |
| Focus | Focus-free |
| Temperature range | -20°C – 400°C |
| Accuracy | ±2°C or ±2%, whichever is greater (-10°C -400°C room temperature |
25°C)
Measurement units| °C/°F
Resolution| 0.1°C
Emissivity| 0.95 (default) 0.01 – 0.99
Temperature display| Center point temperature, high/low-temperature tracking
Palettes| lava, rainbow HC, black hot , white hot, iron, Rainbow
Display type| 2.4″ TFT LCD
Display resolution| 320 x 240
Buttons| 4 buttons (power, up, down, OK) 1 trigger
---|---
Laser| 4(Class 2)
LED Light| 4
Temperature alarms| LCD, LED, buzzer
Image storage| Micro SD Card
Image format| BMP
PC analysis software| 4
USB communication| Type-C USB
Battery| Li-ion 3.7V/2600mAh 18650
Operating time| Continuous operating time >9h
Charging time| s2.5h
Charging voltage/current| 5V 12A
Power on speed| Os (wake up) / 5s (power on)
Auto power off| 5min/10min/30min(default)/off
Operating temperature| 0 – 50°C ( 32 -140°F )
Storage temperature| -20 – 60°C ( -4 – 140°F )
Operating humidity| < 85%RH ( Operating humidity )
IP rating| IP54
Drop-proof| 2m
Product size (LxWxH)| 197 x 72 x 60 mm
Product weight| 310g
Certificates| CE, UKCA, RoHS
Accessories| User manual, Type-C USB cable, 32GB Micro SD card
Structure
| Item | Description | Item | Description |
|---|---|---|---|
| 1 | Upper housing | 9 | Infrared camera lens |
| 2 | Interface protection cover | 10 | Image capture/trigger |
| 3 | Lower housing | 11 | LCD |
| 4 | USB Type-C interface | 12 | OK |
| 5 | SD card slot | 13 | Up |
| 6 | Bracket screw hole | 14 | Power / Back |
| 7 | Laser emission aperture | 15 | Down |
| 8 | LED light |
LCD Indicators/Icons
Display size: 2.4″ (495mm 377mm) Display resolution: 320 (vertical) x 240
(horizontal)
| Item | Description |
|---|---|
| 1 | Center point temperature |
| 2 | Center point |
| 3 | Lowest temperature spot |
| 4 | Date and time |
| 5 | Battery status |
| 6 | Temperature Bar |
| 7 | Highest temperature spot |
Power On/Off
When the thermal imager is not turned on, long press the power button for as
to power on. When the thermal imager is in the suspend state, short press the
power button for 1s to power on.
When the thermal imager is turned on, short press the power button for 1s to
enter the suspend state. Long press the power button for 8s, “power off’ will
show on the screen, and the thermal imager will be turned off.
Menu
Short press the OK button to enter the menu interface. Short press the Back
button to return to the upper menu. Short press the trigger to directly return
to the main interface of the thermal imager.
Image View
In the menu, select Image View, and then short press the OK button to enter
the image viewing interface Press the Up/Down button to select an image. Press
the OK button twice to view the Picture Info or Delete images.
Temperature Mark
In the menu, short press the Up/Down button to select Temper Mark, and then
short press the OK button to enter the temperature mark interface. Center
Point/ Hi/Lo Point/Palette/Date&Time can be set in this interface. For
example, select Center Point, and then press the OK button to turn on/off this
function.
HMO
Alert
In the menu, short press the Up/Down button to select HULO Alert, and then
short press the OK button to enter the alert setting interface. Temper Alert,
Buzzer, HI Alert, and LO Alert can be set in this interface.
LED light
In the menu, short press the Up/Down button to select Hand Light, and then
short press the OK button to turn on/off the flashlight.
Palette
In the menu, short press the Up/Down button to select Palette, and then short
press the OK button to enter the palette selection interface. Short press the
Up/Down button to step through six palettes: Rainbow, Iron, White Hot, Black
Hot, Rainbow HC, Lava, and short press the OK button to confirm the selected
palette.\
Language
In the menu, short press the Up/Down button to select Setting, and then
short press the OK button to enter the submenu. Select Language, and short
press the OK button to switch between English/Chinese
Temperature Unit
In the menu, short press the Up/Down button to select Setting, and then
short press the OK button to enter the submenu. In the submenu, short press
the Up/Down button to select Temper Unit, and short press the OK button to
switch between`C/T.
Emissivity
In the menu, short press the Up/Down button to select Setting, and then
short press the OK button to enter the submenu. In the submenu, short press
the Up/ Down button to select Emissivity, and short press the OK button to set
the emissivity.
Laser
In the menu, short press the Up/Down button to select Setting, and then short
press the OK button to enter the submenu. In the submenu, short press the Up/
Down button to select Laser, and short press the OK button to turn on/off the
laser.
Time & Date
In the menu, short press the Up/Down button to soled Setting, and then short
press the OK button to enter the submenu. In the submenu, short press the Up/
Down button o select Time&Date, and short press the OK button to enter the
setting interface. The Time Format can switch between 12H and 24H. Press the
Up/Down button to adjust the value of time and date, and short press the OK
button to confirm.
Brightness
In the menu, short press the Up/Down button to select Betting, and then
short press the OK button to enter the submenu. In the submenu, short press
the Up/ Down button to Speed Brightness, and short press the OK button to
enter the setting interface. The brightness can be Low, Middle or High.
Auto Power Off
In the menu, short press the Up/Down button to soled Setting~ and then
short press the OK button to enter the submenu. In the submenu~ short press
the Up/ Down button to select Auto Power Off, and short press the OK button to
enter the setting interface. In mis interface, users can set the auto power
off time (5/ 10/3Omin) or tum off the auto power-off function.
Auto Save
In the menu, short press the Up/Down button to soled Setting, and then short
press the OK button to enter the submenu. In the submenu, short press the Up/
Down button to select Auto Save. Short press the OK button to tum on/off the
auto-save function.
Format SD
In the menu~ short press me Up/Down button to select Sanding, and then short
press the OK button to enter the submenu. In the submenu, short press the Up/
Down bunch to select Format SD and short press the OK bunch to enter the
saning interface Press ma OK bunch salad Yes or No.
Device Info
In my menu, short press the Up/Down bunch to select Sanding, and then short
press the OK button to enter the submenu. In the submenu, short press the Up/
Down bunch to select Device Info and short press the OK button to enter the
info mum viewing interface. The device information including Code, Firmware,
Capacity, and Available can be viewed.
Factory Reset
In the menu, short press the Up/Down bunch to select Sanding, and then short
press the OK bunch to enter the submenu. In the submenu, short press the Up/
Down bunch to select Factory Reset and short press the OK bunch to enter the
setting interface. Press the OKand bunch select Yes or No.
USB Communication and PC Analysis Software
- Please refer to the instructions to download and install the PC software.
- Connect the USS data cable to the computer. Users can view images and analyze data via the PC software.
- To use the PC software correctly, please read the Software User Manual.
- During USS communication, do not directly unplug the USS cable. If users want to disconnect the device when it has been successfully connected to the computer, they can select Remove Device in the lower right corner of the
Maintenance
Use a wet cloth or weak soap solution to dean the outer shell of my device. Do
not use abrasive isopyl or solvents toclean the shell.lens or windos.
Safety Instructions
In order to ensure measurement accuracy, please read the instructions
carefully. Please use this product in accordance with the user manual.
Ot,herwise the free warranty will not be carried out if the product is
damaged. Please do not use this product in flammable, explosive, steamy, humid
or corrosive environments. Please do not continue to use the product when it
is damaged, dropped or corrected, so as to avoid erroneous measurement
results. Please refer to the emissivity to get the actual temperature.
Otherwise, the measured temperature will be inaccurate. Charging will cause
the internal temperature of the machine to rise, thereby affecting the
measurement accuracy. Therefore, it is recommended not to take measurements
when charging the product.
Appendix
Material
| Emissivity| Material|
Emissivity
---|---|---|---
Wood| 0.85| Black paper| 0.86
Water| 0.96| Polycarbonate| 0.8
Brick| 0.75| Concrete| 0.97
Stainless steel| 0.14| Copper oxide| 0.78
Adhesive tape| 0.96| Cast iron| 0.81
Aluminum plate| 0.09| Rust| 0.8
Copper plate| 0.06| Gypsum| 0.75
Black aluminum| 0.95| Paint| 0.9
Human skin| 0.98| Rubber| 0.95
Asphalt| 0.96| Soil| 0.93
PVC plastic| 0.93| |
****UNETREND TECHNOLOGY (CHINA) CO., LTD.
Songshan Lake National High-Tech Industrial LG
Development Zone, Dongguan City,
Guangdong Province, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>