D-Parts Fontiso IR-Thermometer User Manual
- June 12, 2024
- D-Parts
Table of Contents
D-Parts Fontiso IR-Thermometer User Manual
Thank you for choosing our Fontiso IRUT infrared thermometers. The contactless and easy-to-use body and surface thermometer enables precise measurements via the integrated infrared sensor within the shortest time.
Overview
- Display
- Mode button (M)
- Measurement on / off button (temperature button)
- Settings / Saves (S)
- Infrared sensor lens
- Battery compartment Display:
- Location of memory group
- Memory location number
- Beep sound
- Degrees Celsius/Fahrenheit
- Surface indication
- Body indication
- Battery status
- Temperature indication
Insert batteries
To open the battery compartment (6), slide the Battery Cover to open and
access the battery compartment. Insert two 1.5V AAA batteries (included) as
shown in the battery compartment. Close the cover.
Attention: Incorrectly inserted batteries, lead to malfunction.
Measuring of Temperature
Note: In order to obtain precise measurement data, the object to be
measured should be at least twice as large as the diameter of the measuring
sensor. The distance to the object to be measured should not exceed 5 cm.
Note: The device switches itself off after 10 seconds if it is not used.
Measuring of Body temperature:
Point the thermometer with the lens at your forehead or armpits. Press and
hold the power button (3). The measuring result is immediately shown on the
display. Temperature ranges are indicated by different colored display
backgrounds and an acoustic signal.
- Green: Normal (temp. Range 32 °C to 37.4 °C)
- Yellow: Increased (temp. Range 37.5 °c to 37.9 °C)
- Red: Fever (temp. Range 38 °C to 42.9 °C)
Note: If the temperature is below 32 °C, the display shows Lo. If the
temperature is above 43 °C, Hi is shown.
Note: If the measured ambient temperature is below 10 °C Erl and if above
40 °C ErH will show in display.
Measurement of surfaces and liquids
First set the measurement to surface measurement, align the thermometer with
the lens at the surface or liquid to be measured. The measurement result is
shown in the display after a short time.
Note: Reflective surfaces can be measured by covering the surface to be
measured with non-reflective adhesive tape and measuring.
Settings
Measurement of body or surface
After switching on the contactless temperature measuring device IRman, press
the button Modes M (3) to select between body temperature or surface
temperature measurement.
Setting the temperature unit (C or F)
After switching on the IRman, please press and hold the S key (4) until F1
appears. There press the Temp key (3) to select between the measurement unit
Celsius or Fahrenheit.
Setting the temperature alarm
After switching on, please press and hold the S key (4) until F1 appears, then
press the S key (4) again until F2 appears in the display. Now you can set
your desired temperature alarm (e.g.) 38 °C instead of the preset 37.1 °C,
button M (2) increases the Setting Value, and button temperature (3) decreases
the Setting Value.
The setting of temperature compensation
After switching on, please press and hold the S key (4) until F1 appears, then
please press the S key (4) twice until F3 appears in the display. Now you can
set the compensation temperature. Button M (2) increase the Setting Value,
and button temperature (3) decreases the Setting Value.
The setting of the speaker’s tone
After switching on, please press and hold the S key (4) until F1 appears, then
please press the S key (4) 3 times until F4 appears in the display. Press
button M (2) to switch on or off the Beep tone,
Note: By pressing the S key (4), the settings are saved and you enter into the measurement menu measuring it.
Cleaning
Lens cleaning: Use a cotton cloth to clean the IR sensor. Cleaning the
housing: Clean the housing with a damp cloth
Caution: Do not use any solvents or harsh cleaners to clean the lens and
housing.
Safety Instructions:
- This device is not suitable for medical use.
- Do not immerse the thermometer in liquids.
- Keep it away from children.
- Do not make self-diagnosis based on the measurement results of the device.
- Follow your doctor’s instructions.
- If there is a difference in temperature between the place of storage and the place of use, keep the device at the place of use for 30 minutes before taking measurements.
- If the forehead/skin is cold/damp, dry the skin and wait 10 minutes before measuring.
- Do not expose the device to direct sunlight, extreme temperatures, or high humidity.
- Remove the batteries if it is not going to be used for a long time.
Technical data
- Display: LCD Display
- Measuring time: Less than a second
- Measuring distance: 3 to 5 cm
- Body temperature: 32°C to 43°C
- Surface temperature:
- Accuracy: ± 0.2° c
- Units of measurement: Celsius/Fahrenheit
- Automatic switch-off: After 10 seconds
- Memory: 20 measurements
- Operating temperature: 10°C to 40°C
- Battery: 2 x 1.5V AAA (included)
- Dimensions: 152 x 40 x 40 mm
- Weight: 73g (without batteries)
No liability is accepted for any damage caused by incorrect operation. In case you need technical support, please contact our support team by e-mail at service@fontastic.eu.No liability is accepted for any damage caused by incorrect operation. In case you need technical support, please contact our support team by e-mail at service@fontastic.eu.
Registration and Safety
Certification/General Information
We hereby declare that this device carries the CE mark in accordance with the
regulations and standards. It conforms with the fundamental requirements of
the EMC directive 2014/30/EU. The full text of the EU Declaration of
Conformity is available at the following internet address:
www.d-parts.de/Konfo
Note on environmental protection
“After the implementation of the European Directive 2012/19/EU in the national
legal A system, the following applies: Electrical and electronic devices and
batteries may not be disposed of with domestic waste. Consumers are obliged by
law to return electrical – and electronic devices at the end of their service
lives to the public collecting points set up for this purpose or point of
sale. Details of this are defined by the national law of the respective
country. This symbol on the product, the instruction manual, or the package
indicates that a product is subject to these regulations. By recycling,
reusing materials, or other forms of utilizing old devices, you are making an
important contribution to protecting our
environment. Subject to technical changes and errors/ Technische Anderungen
und lrrtOmer vorbehalten Fontiso by D-Parts GmbH Birkenweiher Str. 16 63505
Langenselbold, Gernany www.d-parts.de V1_11_20
Download PDF:D-Parts Fontiso IR-Thermometer User Manual