Shelly Plus, Plug S, WiFi Smart Plug User Guide

: June 12, 2024
: Shelly

Table of Contents

Shelly Plus, Plug S, WiFi Smart Plug
Usage Instructions
USER AND SAFETY GUIDE
Product Introduction
Schematic
Installation Instructions
Cleaning
LED indication
Control button
Specification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shelly Plus, Plug S, WiFi Smart Plug

Shelly Plus Plug S

User and Safety Guide

Product Overview
The Shelly Plus Plug S is a WiFi Smart Plug that allows users to remotely control their connected appliances through various home automation platforms and protocols. The device also features LED indication and a control button.

Specifications

Input voltage: 110-230V AC
Maximum load: 2500W
Wireless/WiFi standard: 802.11 b/g/n
Dimensions: 56mm x 56mm x 78mm
Weight: 70g

Usage Instructions

Note: Before using the device, please read the user manual carefully.

Cleaning: Before cleaning the Device, power off the connected appliance, unplug it and only then unplug the Device. Use a wet soft cloth to clean the Device. Do not use aggressive detergents. Do not immerse the Device or wash it under running water.
Disposal and Recycling: This refers to the waste of electrical and electronic equipment. It is applicable in the EU, US and other countries to collect waste separately.
Initial Inclusion: If you choose to use the Device with the Shelly Cloud mobile application and Shelly Cloud service, instructions on how to connect the Device to the Cloud and control it through the Shelly App can be found in the App Guide at www.shelly.cloud/app-guide. The Shelly mobile application and Shelly Cloud service are not not conditions for the Device to function properly. This Device can be used standalone or with various other home automation platforms and protocols.
LED indication: The user can select the brightness. Default brightness is 100%. Green light at 0% of power limit set, yellow light at 50% of power limit set, and red light at 100% of power limit set.
Control button: Use the control button to turn the connected appliance on or off.

Note: Do not allow children to play with the buttons/switches connected to the Device. Keep the devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Declaration of Conformity

The Shelly Plus Plug S conforms to the essential requirements and other relevant provisions of Directive 2014/53/EU.

USER AND SAFETY GUIDE

SHELLY PLUS PLUG S
WIFI SMART PLUG

Read before use
This document contains important technical and safety information about the device, its safety use and installation. CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics EOOD is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.

Product Introduction

Shelly® is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits through a mobile phone, tablet, PC, or home automation system. Shelly® devices can work standalone in a local Wi-Fi network or they can also be operated through cloud home automation services. Shelly Cloud is a service that can be accessed using either Android or iOS mobile application, or with any internet browser at https://home.shelly.cloud/. Shelly® devices can be accessed, controlled and monitored remotely from any place where the user has internet connectivity, as long as the devices are connected to a Wi-Fi router and the Internet. Shelly® devices have Embedded Web Interface accessible at http://192.168.33.1 when connected directly to the device access point, or at the device IP address on the local Wi-Fi network. The embedded Web Interface can be used to monitor and control the device, as well as adjust its settings. Shelly® devices can communicate directly with other Wi-Fi devices through HTTP protocol. An API is provided by Allterco Robotics EOOD. For more information, please visit: <https ://shelly-api-docs.shelly.cloud/#shelly-family-overview>. Shelly® devices are delivered with factory-installed firmware. If firmware updates are necessary to keep the devices in conformity, including security updates, Allterco Robotics EOOD will provide the updates free of charge through the device Embedded Web Interface or the Shelly mobile application, where the information about the current firmware version is available. The choice to install or not the device firmware updates is the user’s sole responsibility. Allterco Robotics EOOD shall not be liable for any lack of conformity of the device caused by failure of the user to install the provided updates in a timely manner. Shelly Plus Plug S (The Device) is a smart plug/outlet with power measurement and overheating protection, which allows remote control of electric appliances through a mobile phone, tablet, laptop, or home automation system. It can work standalone in a local Wi-Fi network or it can also be operated through cloud home automation services.

Schematic

Legend

A: Socket
B: Control button
C: Plug
D: LED indication ring

Installation Instructions

CAUTION! The product is intended for indoor use only.

Protect the product from dirt and moisture! Do not use the product in a damp environment!
Do not allow children to play with the device, especially with the control button!
Use the Device only with a power grid and appliances which comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.
Do not connect the Device to appliances exceeding the given max load!
Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury. Insert Shelly Plus Plug S into a power socket without an appliance/load connected to it. The LED indication ring will start flashing with a blue light, indicating the Device is in Access Point (AP) mode. You can access the embedded web interface at http://192.168.33.1 in the Wi-Fi network, created by the Device (ShellyPlusPlugS-XXXXXXXXXXXX) and use it to control the Device and change its settings. You can now plug an appliance into the Device socket. To turn the appliance on, press briefly the control button. The LED indication ring will illuminate. The light color depends on the load (check LED indication below). Press the control button again to turn the appliance off. The LED indication will return to its previous status.

Cleaning

CAUTION!

Before cleaning the Device, power off the connected appliance, unplug it and only then unplug the Device. Never clean the Device if it is connected to the mains! Use a wet soft cloth to clean the Device.
Do not use aggressive detergents!
Do not immerse the Device or wash it under running water!

Disposal and recycling

This refers to the waste of electrical and electronic equipment. It is applicable in the EU, US and other countries to collect waste separately.
This symbol on the product or in the accompanying literature indicates that the product should not be disposed of in the daily waste. Shelly® Plus Plug S must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources. It is your responsibility to dispose of the device separately from general household waste when it is already unusable.

Initial Inclusion

If you choose to use the Device with the Shelly Cloud mobile application and Shelly Cloud service, instructions on how to connect the Device to the Cloud and control it through the Shelly App can be found in the “App Guide” at www.shelly.cloud/app-guide.

The Shelly mobile application and Shelly Cloud service are not not conditions for the Device to function properly. This Device can be used standalone or with various other home automation platforms and protocols.

CAUTION! Do not allow children to play with the buttons/switches connected to the Device. Keep the devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

LED indication

When plugged for the first time:

Blue light flashing, indicating AP mode.

When plugged/powered again after being successfully connected to a Wi-Fi network:

Red light flashing, indicating the Device is reconnecting to the Wi-Fi network.

When output is On:

Power consumption is represented by a smooth color change (Default).
User can select the brightness (Default brightness – 100%):
- Green light at 0% of power limit set
- Yellow light at 50% of power limit set
- Red light at 100% of power limit set
Custom color (Default color – green, Default brightness – 100%)
Off
When out put is Off:
Off (Default):
Custom color (Default color – red, Default brightness – 100%)

When the control button is pressed and held for 3 sec (only when the Device output is Off):

Red light flashes three times, indicating the Device is not connected to the Wi-Fi network.
Yellow light flashes three times, indicating the Device is connected to the Wi-Fi network, but not to Shelly Cloud.
Green light flashes three times, indicating the Device is connected to Shelly Cloud.

Control button

Press to turn on/off the plugged appliance.
Press and hold for 3 sec to check the Device status*
Press and hold for 5 sec to activate Device AP**
Press and hold for 10 sec to factory reset* Only when the output is Off. ** Only within 1 min after plugging/powering the Device.

Specification

Dimensions (HxWxD): 44x44x70 mm / 1.73×1.73×2.75 in
Weight: 60 g / 2.08 oz
Compatible sockets: CEE 7/1, CEE 7/3 (Type F / Schuko) or CEE 7/5 (Type E)
Compatible plugs: CEE 7/2, CEE 7/4 (Type F / Schuko), CEE 7/7, CEE 7/16 (Type C) or CEE 7/17
Ambient temperature : from -20 °C to 40 °C / from -4 °F to 104 °F
Humidity: 30 % to 70 % RH
Max. altitude 2000 m / 6,562 ft
Power supply: 230 VAC ±10 %, 50/60 Hz
Electrical consumption: < 1 W
Max. current: 12 A
Max. power: 2500 W (resistive load only)
Overheating protection: Yes
Overload protection : Yes
Power measurement: Yes
RF band: 2401 – 2495 MHz
Max. RF power: < 20 dBm
Wi-Fi protocol: 802.11 b/g/n
Wi-Fi operational range (depending on local conditions):
- up to 50 m / 160 ft outdoors
- up to 30 m / 100 ft indoors
Bluetooth protocol: 4.2
Bluetooth operational range (depending on local conditions):
- up to 30 m / 100 ft outdoors
- up to 10 m / 33 ft indoors
CPU: ESP32
Flash: 4 MB
Schedules: 20
Webhooks (URL actions): 20 with 5 URLs per hook
Scripting: mJS
MQTT: Yes

Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly Plus Plug S is in compliance with Directive 2014/53/EU, 2014/35/ EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/plus- plug-s-DoC Manufacturer: Allterco Robotics EOOD Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria Tel.: +359 2 988 7435 E-mail: support@shelly.cloud Official website: https://www.shelly.cloud Changes in the contact information data are published by the Manufacturer on the official website.https://www.shelly.cloud All rights to the trademark Shelly® and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.