zapperbox A1 Indoor, Outdoor Antenna User Guide
- October 30, 2023
- ZapperBox
Table of Contents
A1 Indoor/Outdoor Antenna by Televes
User Guide
FEATURES
- Built-in amplifier
- Integrated LTE filter
- Removable reflector
- Integrated 5G antenna
IN THE BOX
NOTE: SHOULD I USE THE REFLECTOR?
Using the reflector can greatly enhance the forward gain of an antenna,
particularly indoors where multipath reflections from bouncing signals cause
reception issues. With a reflector, interference from the rear is minimized
and gain in the forward direction is increased, resulting in better
performance. However, antennas with reflectors need to be aimed towards the
direction of the towers. If the signal is very strong, going without a
reflector may be an option to increase omnidirectionality.
Nevertheless, it is generally recommended to use a reflector and aim the
antenna towards the transmitters for optimal performance, as broadcast
television relies on line-of-sight signal delivery.
Does a reflector improve reception for both ATSC 1.0 and ATSC 3.0
signals?| Should the reflector be used outdoors too?
---|---
YES.| YES.
Installation Instructions
TABLE MOUNT (WITH REFLECTOR)
Step 1
Remove the pole mounting hardware from the Reflector (E) using the included
Wrench (J).
Step 2
Place the Reflector (E) in the position shown below and fasten with included
Screws (D).
Fully Assembled for Table Mount
WALL MOUNT (WITH REFLECTOR)
Step 1
Remove the pole mounting hardware from the Reflector (E) using the included
Wrench (J).
Step 2
Place the Reflector (E) in the position shown below and fasten with included
Screws (D).
Step 3
Attach to wall using 2 screws (not included).
POLE MOUNT (WITH REFLECTOR)
Step 1
Place the Reflector (E) in the position shown below and fasten with included
Screws (D).
Step 2
Attach the antenna to a pole with the Clamp (B) and Wing Nuts (C).
Antenna Connections
- 5G Cellular Out*
- For future use (MIMO)*
- TV Connection
*Input 1 and 2 are capped and terminated to reduce noise interference.
- Connect the Power Injector (G) to your ZapperBox/Set-top Box/TV.
- Use the RF Cable (I) to connect the Power Injector (G) to Output 3 on the Antenna (A).
- Use the USB Cable (F) to connect the Power Injector (G) to the Power Adapter (H).
- Plug the Power Adapter (H) into a wall receptacle.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Manufactured and Imported by:
Televes USA LLC, Norfolk Tech Center
16596 E. 2nd Ave, Aurora, CO 80011
televes.usa@televes.com| Distributed
by:
ZapperBox
1776 22nd Street, Suite 200
West Des Moines, IA 50266
info@zapperbox.com
---|---
Safety Instructions
LIGHTNING PROTECTION
- If installed outdoors, be sure the antenna system is grounded so as to provide protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code ANSI/ NFPA70, or CSA C22.1 sections 10, 16, and 54, of the Canadian Electrical Code, provide information with respect to proper grounding of the mast nd supporting structure, grounding of the antenna lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode (see figure and instructions).
- Mount the lightning arrestor or 75 ohm coaxial grounding block as close as possible to where the 75 ohm coaxial cable down lead enters the house.
- The ground wires for both the mast and the down lead should be copper or aluminium wire, number eight (8) or larger.
- The down lead wire from the antenna to the lightning arrestor and the mast ground wire should be secured to the house, spaced from four (4) to six (6) feet apart.
- In the case of a “ground up” antenna installation it may not be necessary to ground the mast if the mast extends four or more feet in the earth. Consult a TV serviceman for the proper depth in your location.
WARNINGS
- To prevent fire or shock hazard, do not expose the included power supply to rain or moisture.
- Installation of off-air antennas near power lines is dangerous. For your safety, follow the installation instructions.
- Any alteration or modification to the product or usage not in accordance with product instructions voids the warranty.
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
TECHNICAL SPECIFICATIONS
Outputs | 5G | VERTICAL | HORIZONTAL |
---|---|---|---|
Frequency | 630 – 960 MHz | ||
1.7 – 2.7 GHz | UHF |
(Ch.14 – Ch.36)
470 – 608MHz| High VHF / UHF
(Ch.7 – Ch.13) / (Ch.14 – Ch.36)
174-216 MHz / 470-608 MHz
Gain| OdBi| 32dBi| 23dBi/dBi32*
Crosspolar rejection| >13dB
Power| 150mA @ 5V DC
Dimensions| 14″ x 14″ x 4″ (w/o pole mount)
Temp. Range| -5°C – 45°C
IP Rating| IP53
*Self-regulating gain.
Notes: ——————-
zapperbox.com
v1.0
Documents / Resources
|
zapperbox A1 Indoor, Outdoor
Antenna
[pdf] User Guide
ZXA1, A1 Indoor Outdoor Antenna, A1 Indoor Antenna, A1 Outdoor Antenna, Indoor
Outdoor Antenna, Antenna, A1 Antenna, Indoor Antenna, Outdoor Antenna
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>