V-TAC VT-5131-2 Wireless Switch User Manual

V-TAC VT-5131-2 Wireless Switch

Product Appearance

Note : The product depicted in this manual may appear slightly different from what you receive in the box

Introduction

Based on radio frequency (RF) and energy harvesting technology, a wireless switch does neither needs an external power supply to control. When pressing the button, the mechanical energy automatically converts into electrical energy. Meanwhile, the switch will send out radio signals to control the receiver on/off.

Installing Receiver

WARNING!
Please power off before installation!

Fix the lines as per below picture

Application

（Home, hotel, inn or Factory etc.）

• The integrated load of the wireless receiver is 1000W
• A one-gang wireless switch controls a wireless receiver
• A two-gang wireless switch controls 2 wireless receivers
• A receiver can be controlled by 8pcs of wireless switch panels at most
• Three two-gang wireless switch controls 2 wireless receivers
• A three-gang wireless switch controls 3 wireless receivers
• A hand remote control controls 3 wireless receivers

Code Operation

PAIRING THE SWITCH & THE RECEIVER

1. Connect the receiver between the light and the power source.
2. Power on electricity, and press and hold the setting button for 2 seconds. When the indicator light flashes, it enters the matching code mode, then loosen your finger.
3. Press the wireless switch button that you want to pair. Use the wireless switch to control the light on or off, indicating that the learning code is successful.

NOTE :

• Not recommended that 1 switch controls many receivers.
• Ensure that there is no other painting within 100 mtrs rang e to avoid interface

ADDING ANTOTHER SWITCH TO A PAIRED SWITCH

Press and hold paired switch panel for about 20s till LED indic ator on switch blinks rapidly, then loosen your finger, press the new one, finally test whether it can turn on/off the lamps

DELETING ADDITIONAL SWITCH FROM A PAIRED SWITCH

Press and hold paired switch panel for about 60s, during which LED indicator on switch changes from: firstly blinks rapidly; secondly blinks 8 times slowly, thirdly blinks 9 times at slower speed, finally blinks once at slowest speed, then loosen

UNPAIRING THE RECEIVER

Press and hold the receiver button for about 10s, loosen your fi nger when the indicator light changes from rapid blinks to slower, press the paired switch panel cannot control the lamps

How to set Open/Close state of the receiver to make wireless switch compatible with the traditional switch

Note: The receiver is the default in the Close state.

1. Power off electricity, install the receiver as the diagram and distinguish live from neutral lines.
2. Power on electricity, then program receiver with the switch according to the Learning code Operation chapter

If the receiver is in the open state

• Turn on the traditional switch to light the lamps, the wireless switch can control the lamps.
• Turn off the traditional switch to light the lamps, the wireless switch cannot control the lamps

If the receiver is in the open state,

• Turn on the traditional switch and press the wireless switch to light the lamps, the wireless switch can control the lamps.
• Turn off the traditional switch, the wireless switch cannot control the lamps.

Method of set the receiver in Open state

Press and hold the switch button for 16s, and loosen your finger when the indicator light is continuously bright. (During the 16s, the indicator light will change from quick flash to slower flash, after that, the indicator light will be off, then will be on.)

Method of set the receiver in a Close state:

The same method of set the receiver in an Open state, just press and hold the setting button for 16s, and loosen your finger when the indicator light is continuously bright.

Replace the battery

1. Remove switch frame and panel with hand or screwdriver.
2. Remove 4 screws with screwdriver, take off the battery cover ;
3. Replace the old battery with the new one, pay attention to the positive and negative poles of the battery;
4. Install the panel and frame again.

INSTALLATION WIRELESS SWITCH

The switch can be surface mounted with screws or double-sided stickers. or set it on the table.

1. Install with Double-sided adhesive. (Included)

Pick up the area where you ’re going to place the switch, clean the surface with wet rag, post the adhesive rubber in the back of the switch, then attach the switch to the clean surface

1. Install with screws (not included)

First, take apart the frame and button panel of the switch, Fix the switch base on the wall with two screws, then install the parts together

Specifications

Parameters of the wireless receiver

Product Size

|

392322MM

|

Working voltage

| AC 150~275V

or 80~150V

---|---|---|---
Switch times| ＞400,000 times| Working frequency| 433.932 MHz +/-75KHz
Sensitivity| -116dB| Relay| 10A
Working current| ≤0.8W| Standby current| ≤0.5W
Resistive load| 1800W| Composite load| 1000W (LED)
Temperature rise when working| ≤15| Fireproof PC| CHIMEI
Signal light

on the receiver

| Red light| Package weight| 32~35g

Parameters of the metal hand remote

≥20m indoor

Parameters of the wireless switch

Product Size

| 868611MM

or

868613MM

|

Type

| 1-gang,2gang, 3-gang
---|---|---|---
Switch times| >600,000 times| Working frequency| 433.932 MHz +/-75KHz
Sensitivity| -116dB| Working voltage| 3V（CR2032）
Package weight| 82~86g| Life of the battery| ≥300,000 times
Emission current| ≤30 mA| Standby current| ≤0.01 uA
Working temperature| -40~+70| Waterproof| IP54
Working characteristics| No need wiring| Fireproof PC| CHIMEI
Remote distance| ＞600m outdoor| Light on the switch| Blue light

Remote distance

| ＞40m indoor|

Interchangeable panel

| The three kinds of panels can be interchangeable

Incase of any queries/issues, kindly reach out to us at support @vtacexports.com For more product ranges, kindly contact our distributors or nearest dealers. V-Tac ( UK ) Limited, Springheath House, Kelpatrick Road, Slough

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>