hansgrohe 34112000 AXOR CITTERIO M Washbasin Mixers Instruction Manual
- October 30, 2023
- hansgrohe
Table of Contents
- hansgrohe 34112000 AXOR CITTERIO M Washbasin Mixers
- Product Information
- Technical Data
- Installation Information
- Product Usage Instructions
- Technical Data
- Assembly
- Dimensions
- Flow diagram
- Spare parts
- Operation
- Cleaning
- Test certificate
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe 34112000 AXOR CITTERIO M Washbasin Mixers
Product Information
The product is a shower system with a single lever mixer and a hot water limiter. The shower system is designed for bathing, hygienic, and body cleansing purposes. The hot and cold water supplies must have equal pressures. The shower system has a flow limiter and can operate at a maximum pressure of 1 MPa. The recommended operating pressure is 1.6 MPa. The recommended hot water temperature is not specified.
Technical Data
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 1.6 MPa
- Test pressure: 1.6 MPa
- Hot water temperature: not specified
Installation Information
Gloves should be worn during installation to prevent crushing and cutting injuries. The shower system must only be used for bathing, hygienic, and body cleansing purposes. The hot and cold water supplies must have equal pressures to avoid any damage. The hot water limiter on single lever mixers can be adjusted by referring to page 32 of the manual. No adjustment is necessary when using a continuous flow water heater. Do not use silicone containing acetic acid. An installation kit is not included in the product packaging and needs to be ordered separately.
Flow Diagram
A flow diagram is provided on page 33 of the manual.
Spare Parts
The spare parts are listed on page 36 of the manual.
Cleaning Instructions
Cleaning instructions are provided in an enclosed brochure.
Product Usage Instructions
Before using the shower system, ensure that the hot and cold water supplies have equal pressures. Follow the steps mentioned below for using the product:
- Turn on the water supply.
- Adjust the temperature of the water by using the single lever mixer.
- Use the shower system for bathing, hygienic, and body cleansing purposes.
Refer to page 34 of the manual for detailed information on operating the
product.
Refer to the enclosed brochure for cleaning instructions.
Assembly Instructions
Refer to page 31 of the manual for detailed assembly instructions.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The shower system may only be used for bathing, hygienic and body cleansing purposes.
- The hot and cold supplies must be of equal pressures.
Installation Instructions
The fitting must be installed, flushed and tested after the valid norms. If
the instantaneous water heater causes problems or if you wish to increase the
water flow, the EcoSmart® (flow limiter) located behind the aerator can be
removed. Hansgrohe mixers can be used together with hydraulically and
thermically controlled continuous flow heaters if the flow pressure is at
least 0,15 MPa.
Technical Data
This mixer series-produced with EcoSmart® (flow limiter)
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5 MPa
- Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 80°C
- Recommended hot water temp.: 65°C
Assembly
Symbol Description
To adjust the hot water limiter on single lever mixers, please see page 32.
No adjustment is necessary when using a continuous flow water heater
Do not use silicone containing acetic acid!
Dimensions
Flow diagram
- with EcoSmart®
- without EcoSmart®
Spare parts
Special accessories
Installation kit order as an extra
Operation
Cleaning
Test certificate
Hansgrohe · Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282
· Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet:
www.hansgrohe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>