hansgrohe AXOR 39112000, 39115000 Citterio Instruction Manual
- October 30, 2023
- hansgrohe
Table of Contents
- hansgrohe AXOR 39112000, 39115000 Citterio
- Product Information
- Product Usage Instructions
- Safety Notes
- Installation Instructions
- Technical Data
- INSTALLATION INSTRUCTION
- Symbol Description
- Dimensions
- Flow diagram
- Spare parts
- Special accessories
- Operation
- Cleaning
- Test certificate
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe AXOR 39112000, 39115000 Citterio
Product Information
The Citterio 39112000 / 39115000 is a shower system designed for bathing, hygienic, and body cleansing purposes. It comes with installation instructions, technical data, spare parts, and special accessories. The shower system has a maximum operating pressure of 1 MPa and a recommended operating pressure of 1.6 MPa. The hot and cold supplies must be under equal pressure to ensure proper functioning. The system has a limiter to control the water temperature and prevent scalding. The shower system operates at a hot water temperature of up to the recommended temperature level. The package does not include an installation kit and silicone containing acetic acid should not be used for installation.
Product Usage Instructions
Before using the Citterio shower system, ensure that the hot and cold supplies are of equal pressure. Gloves should be worn during installation to prevent crushing and cutting injuries. Follow the installation instructions provided in the manual for proper installation of the shower system. The shower system operates at a maximum pressure of 1 MPa and a recommended pressure of 1.6 MPa. The limiter controls the water temperature to prevent scalding and must not be tampered with. The hot water temperature should not exceed the recommended temperature level. Silicone containing acetic acid should not be used during installation. Refer to the flow diagram on page 33 for more information on the water flow rate. To clean the shower system, follow the instructions provided on page 35 of the manual. Spare parts and special accessories are available for purchase separately.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The shower system may only be used for bathing, hygienic, and body cleansing purposes.
- The hot and cold supplies must be of equal pressure.
Installation Instructions
- The fitting must be installed, flushed, and tested after the valid norms.
- If the instantaneous water heater causes problems or if you wish to increase the water flow, the EcoSmart® (flow limiter) located behind the aerator can be removed.
- Hansgrohe mixers can be used together with hydraulically and thermally controlled continuous flow heaters if the flow pressure is at least 0,15 MPa.
Technical Data
- This mixer series-produced with EcoSmart® (flow limiter)
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5 MPa
- Test pressure : 1,6 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature : max. 80°C
- Recommended hot water temp. : 65°C
INSTALLATION INSTRUCTION
open
close
cold
hot
Symbol Description
Do not use silicone-containing acetic acid!
Dimensions
(see page 33)
Flow diagram
(see page 33)
- with EcoSmart®
- without EcoSmart®
Spare parts
(see page 34)
Special accessories
- Installation kit order as an extra
Operation
(see page 32)
Cleaning
The QuickClean cleaning function only needs a small manual rub over to remove the limescale from
(see page 35) enclosed brochure
Test certificate
P-IX DVGW SVGW WRAS KIWA NF ACS ETA 39112000 P-IX 18117/I0 DVGW BR5789 X X 39115000 P-IX 18117/I0 DVGW BR5789 X X
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>