innociusa 81276 One Piece Single Flush Toilet User Guide
- October 30, 2023
- innociusa
Table of Contents
USER GUIDE
ONE PIECE SINGLE-FLUSH TOILET
Model Number: 81276
TOOLS AND MATERIALS YOU MAY NEED
PACKAGE CONTENTS
BEFORE INSTALLATION
Please make sure the following requirements are met.
- Minimum distance between finished wall and center of the floor drain should be 12”.
- Minimum distance between the center of the shut-off valve to the center of the drain should be 8-1/2” (FIG 1).
INSTALLATION
- Install new floor bolts into floor flange. (FIG 2)
- Attach flexible water supply line (not included) to the inlet of the fill valve and hand tighten ONLY. At this point, DO NOT connect to the water shutoff valve. (FIG 3)
- Place the new Wax Ring around the waste flange of toilet bowl. (FIG 4)
- Lower the toilet onto the closet bolts, so the bolts project through mounting holes in base of toilet. (FIG 5) Using a rocking motion, press the bowl down to position the toilet onto the flange
- Install plastic cap washers, followed by metal washers, nuts and plastic caps onto the closet bolts. (FIG 6) Tighten the bolts alternately until toilet is firmly seated on the floor. CAUTION: DO NOT OVERTIGHTEN NUTS, SEVERE DAMAGE MAY OCCUR
- Connect the flexible water supply line (not included) to the shut-off valve. Tighten coupling nutsecurely. (FIG 7)
- Turn on water supply valve and allow tank to fill until float valve rises to shutoff position. Check for leakage at fittings, tighten or correct as needed.
WARRANTY
1-Year Limited Warranty
Our products have been manufactured under the highest standards of quality and
workmanship. innoci usa warrants to the original purchaser that our products
are free from any defects in material and workmanship by normal use for 1 year
from the date of purchase. A replacement for any defective part will be
supplied FREE OF CHARGE for installation by you.
This warranty is valid to the original purchaser only and does not cover
product damage due to installation error, product abuse, product misuse, etc.
whether or not performed by professionals. innoci usa will not be responsible
for labor charges and/or damage incurred in installation, repair or
replacement nor for any incidental or consequential damages. All warranty
claims should be sent to customerservice@innoci-
usa.com or call 1.866.479.8076. Our
customer service representative will contact you promptly to help you go
through the process until you are completely satisfied with our products.
SHORTAGE OR DAMAGED PRODUCTS All shipments are carefully inspected and counted
before leaving our distribution centers. Please inspect carefully on receipt
of merchandise, noting any discrepancy or damage on the carrier’s freight bill
at that time, and file a claim with the carrier within 10 days from receipt of
order. Then contact our office. Deductions from invoices for shortages or
damage claims will not be allowed.
RETURN NEW GOODS All claims for returns or adjustments must have prior
approval and return authorization (RA) number. Only original, sealed product
in salable condition are eligible for return. Credit for authorized returns
will be issued at the net price paid for the product and subject to a 15%
restocking/handling fee. Merchandise is to be returned via prepaid freight.
All unauthorized returns will be refused or subject to a 25%
restocking/handling fee.
To request an “RA” number: Contact our Customer Service Representatives at
customerservice@innoci-usa.com.
We will send you a Return Authorization Number (RA) by return email. Please
take necessary precautions when returning merchandise to prevent additional
damage. Insurance is the responsibility of the shipper.
TROUBLESHOOT
-
There is not enough flushing power
a. Try to lengthen the actuator rods located under the tank lid. A small amount at a time. If water start leaking from tank to bowl, the actuator rods are adjusted too long.
b. Try to adjust the fill valve to a higher level. (Refer to fill valve manual)
c. Try to adjust the flush valve to a higher level. (Refer to flush valve manual) -
Water keep leaking from tank to bowl
a. Try removing the tank lid. If the leaking stop, try to shorten the actuator rods located under the tank lid.
b. Try to clean the seat and seal under the flush valve. Turn the flush valve approx. 45 degrees clock-wise to lift the flush valve body up. Clean the seat and seal and put it back.
innoci usa, Inc.
14530 Best Ave,
Santa Fe Springs, CA 90670
www.innoci-usa.com
© innoci usa, Inc. All rights reserved.
Customer Service: (866) 479-8076 orcustomerservice@innoci-
usa.com
References
- USA Location information - USA.com
- Homepage, innoci-usa, illumirror, innovanity, innofaucet, electric mirror, lighted mirror
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>