EPOS IMPACT SDW 30 HS, 60 HS Headset Instruction Manual
- October 30, 2023
- EPOS
Table of Contents
EPOS IMPACT SDW 30 HS, 60 HS Headset
Product Information
The IMPACT SDW 30 HS and SDW 60 HS are headsets that come with a rechargeable battery pack. The battery pack is replaceable and can be disassembled and assembled using the instructions provided in the user manual. It is important to follow the safety instructions provided to avoid any damage to the product or harm to the user.
Safety instructions
General
Always check the safety and testing regulations that are currently valid
for your country and abide by the following regulations:
- Repair-related (e.g. in accordance with VDE 0701 in Germany).
- Device-related in accordance with IEC 62368-1.
- Unauthorized alterations and modifications are not permitted for safety and certification reasons. The person who performs unauthorized modifications is liable for any resulting damage.
- Comply with ESD regulations when working around components that are susceptible to electrostatic discharge.
- Modifications and repairs may only be performed by skilled personnel (e.g. in accordance with VDE 1000 in Germany).
- When repairing a device or replacing single components you have to use the original parts from the device‘s current spare parts list. When other than the original parts are used the approval/certification of the device becomes invalid!
- Observe the safety instructions and the disposal regulations of the Lithium-Polymer battery pack.
Safety instructions for rechargeable batteries
WARNING! In extreme cases, abuse or misuse of Lithium-Polymer battery
pack can lead to: explosion, fire, heat or smoke or gas.
- Do not crush, puncture, short circuit, disassemble, expose to moisture, heat or store above 70°C/158°F or dispose of in fire or water.
- Only use the battery pack for designated product(s).
- Read instructions in the product Safety Guide before using the battery.
- Keep battery out of reach of children and in original package until ready to use. Never put batteries in mouth.
- Recycle or dispose of used batteries according to instructions.
- Only use rechargeable batteries recommended by DSEA A/S and the appropriate chargers.
- Do not expose to moisture.
- Switch rechargeable battery-powered products off after use.
- Only charge rechargeable batteries at ambient temperatures between 10°C/50°F and 40°C/104°F.
- When not using rechargeable batteries for extended periods of time, charge them regularly (about every 3 months).
- Do not mutilate or dismantle.
- Do not heat above +70°C/158°F, e.g. do not expose to sunlight or throw into a fire.
Disassembling the rechargeable battery pack
Required material
- new Battery pack for SDW 30 HS | SDW 60 HS – ID No. AHB732038TPCT
- Tool such as a small plastic rod and paper clip for SDW 60 HS
Opening the battery compartment
CAUTION!
Damage to the product due to improper handling!
The wires can be kinked or damaged if you open the battery compartment too
jerkily.
- Carefully open the battery compartment.
- Slide one finger into the small recess on the side support. The battery compartment lifts a bit
- Gently remove the battery compartment cover.
- Use a paper clip or similar tool to press the unlock button and turn the cover a bit.
Removing the rechargeable battery
- Use a plastic tool (e.g. small plastic lifting rod) to lift the rechargeable battery. Please note, that the battery is attached with an adhesive.
- Remove the rechargeable battery.
- Carefully loosen the connector plug.
Assembling the new battery pack
- Rotate the battery so that the marking signs are visible at the top.
- Insert the connector plug of the new rechargeable battery into the connection socket. Observe correct orientation of the connector plug.
- Press on the plastic parts to securely lock the connector plug.
- Insert the battery and assure that the marking signs are visible at the top. Place the battery centered to secure an air gap around it.
- Make sure that the wires are aligned and not crossing over each other. Gently press down the three wires and the battery.
- Slide in the battery compartment cover.
- Start attaching the lower side (as shown) and then push the other side down. Finally, push the sides into place.
- Close the battery compartment and turn the lid clockwise. You hear a click.
Testing the battery and final adjustments
- Test the function of the headset: Press the Hook button to switch on the headset. The LED lights up blue.
- Charge the battery for at least 20 minutes before using the headset. See User Guide for further information.
- Switch off the headset before sending it to the customer. Press and hold the Hook button for 5 seconds. The headset switches off. The Headset LED flashes red 3 times and turns off.
DSEA A/S
Kongebakken 9, DK-2765 Smørum, Denmark
www.eposaudio.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>