V-MARK Gen2 Temperature Tag User Guide
- October 30, 2023
- V-Mark
Table of Contents
V-MARK Gen2 Temperature Tag
Product Usage Instructions
- To use the Temp Tag, activate it using an NFC NDEF message.
- The LED indicator will blink fast 10 times, indicating that the device is searching for a network to join.
- Once the device has joined a network, it can interact with other devices via Thread commands.
- The Temp Tag can be put into hibernate mode by sending an NFC NDEF message.
- The LED indicator will remain on for about 2 seconds, indicating that the device has entered hibernate mode.
- To reset the device, send an NFC NDEF message.
- The LED indicator will remain on for about 2 seconds, indicating that the device has been reset.
- Make sure to maintain a minimum distance of 20cm between the device and your body to comply with FCC’s RF Exposure guidelines.
Introduction
The Temp Tag described in this user guide is using a Thread device , it has been tested to work with Thread Mesh network. This device can be controlled by NFC NDEF messages. In the picture below we can see the Temp Tag with LED. The NFC coil Antenna is around the LED cover.
Out of the box
The Temp Tag comes in a deep sleep state to extend battery life, at this point it can only be triggered by NFC reader. This device should join a network to be able to interact with other ones via Thread commands.
User interface
The Temp Tag has one LED for display; the device can execute different actions
depending on the NDEF messages.
The following table shows the according actions:
| NFC NDEF message | LED indicator | Action |
|---|---|---|
| activate | Fast blink 10 times | Network steering / finding |
| hibernate | Keep on about 2s | Set the device into deep sleep mode |
| reset | Keep on about 2s | Reset the device |
Working Parameter
| Parameter | Value |
|---|---|
| Work Frequency | Thread 2.4GHz and NFC 13.56MHz |
| TX Power | Max 8dBm |
| Battery | ER14250, 3.6V, 1200mAH |
Measuring range
| TMP117 on board: ‐40℃~85℃，±0.1℃（‐20℃~55℃）；
SHTC3：‐40℃~85℃，±0.2℃（‐20℃~55℃）；
SHTC3：0~100%RH， ±2%（20%RH~80%RH）；
Battery Life| 5 years
Operating Temperature| ‐40℃~85℃
Storage Environment| ‐40℃~85℃, No condensation
Size| 88mm45mm19mm
FCC Warnings
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, this equipment should being stalled and operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
V-Mark Enterprises Ltd.
Add.: 400-601 West Broadway, Vancouver BC, Canada V5Z 4C2
Phone: 604.588.6178,
Fax: 604.859.8818,
Email: info@v-mark.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>