TURNER HASTINGS TRTSB 7 Day Programmable Timer User Guide

: October 30, 2023
: TURNER HASTINGS

Table of Contents

TURNER HASTINGS TRTSB 7 Day Programmable Timer
Installation & User Guide
Installing the timer

TURNER HASTINGS TRTSB 7 Day Programmable Timer

TRTS / TRTSB / TRTSL 7 Day Programmable Timer

Installation & User Guide

Contents

Installing the timer
User Interface
Setting the date & time
Heating modes
Advanced settings
Setup your heating schedule
Factory Reset
Temporary override
Holiday Mode
Key lock
Technical data
Service and support

Installing the timer

Carefully remove the back of the timer by placing a flat head
screwdriver into the slots on the bottom of the unit and push to
release.
Unplug the cable connector from the back of the timer
screen.
Connect the Turner Hastings towel rail to the timer as seen in
the below wiring diagram.
Screw the back plate of the timer to the electrical plate.
Plug the cable connector into the back of the timer screen and
connect the screen to the back of the timer.

User Interface: Portrait

Day indicator
Key lock icon
Schedule mode icon
Manual mode icon
ON/OFF indicator
Confirm settings
Program button
Mode button
Power button
Up & down arrows
Time

User Interface: Landscape

Day indicator
Key lock icon
Schedule mode icon
Manual mode icon
ON/OFF indicator
Confirm settings
Program button
Mode button
Power button
Up & down arrows
Time

Setting the date and time

Press the “Mode” button and the time will begin to flash.
Use the “Up & down arrows” to select the correct time.
Press the “Mode” button until the day begins to flash. (Note:
Monday is Day 1)
Use the “Up & down arrows” to select the correct day.
Press the “Confirm settings” button to save the settings.

Heating Modes

When the timer is on, press the “Mode” button to switch between manual and schedule modes.

Manual Mode
In manual mode press the “ON/OFF” button to set the status.

Schedule Mode
In the schedule mode, the timer will follow the heating schedule that is set. Refer to page 9 for programming instructions.

Advanced Settings

To access the advanced settings, turn the timer off by pressing the “Power” button.
Press the “Mode” button to display setting 01.
Use the “Up & down arrows” to adjust the settings.
Press the “Mode” button to cycle between setting 01 to 03.
Press the “Confirm settings” button to save the settings.

Menu	Description	Range	Default
01	Clock Format	12 or 24	24
02	5+2 or 7 Day Programming	01=5+2 Day Program
02=7 Day Program	01=5+2 Day Program
03	Screen Saver	ON=Activated
OF=Not Activated	OF=Not Activated

Set up your heating schedule

(For 5+2 Day Program)

Turn the timer on by pressing the “Power” button.
To set up the heating schedule for Monday to Friday press “Program” button.
The time for P1 will flash. This is the first ON period for the day.
Use the “Up & down arrows” to adjust the time to when the heated towel rail will turn on in the morning.
Press “Confirm settings” and the ON / OF will flash.
Using the “Up & down arrows” select ON for P1.
Press “Program” to set period 2, which is when the rail will turn off. Use the “Up & down arrows” to adjust the time.
Press “Confirm settings” and the ON / OF will flash.
Using the “Up & down arrows” select OF for P2.
Repeat above steps for P3 and P4 and then press (Note: P3 is turning the heated towel rail on in the evening and P4 is turning it off in the evening)

Factory Reset
To perform a factory reset, press and hold the “Program” button and “Power” button simultaneously for 5 seconds. The timer will reset to its default settings.

Temporary override
To temporarily override the current heating schedule, press the “ON/OFF” button. The override will remain in effect until the next scheduled period begins.

Holiday Mode
To activate holiday mode, press and hold the “Confirm settings” button for 5 seconds. The timer will enter holiday mode and all scheduled heating periods will be cancelled. To exit holiday mode, press any button.

Key lock
To lock the timer and prevent accidental changes, press and hold the “Mode” button and “Confirm settings” button simultaneously for 5 seconds. To unlock, repeat the process.

Technical data
Refer to the technical data section of the user manual for information on voltage, power consumption, and other specifications.

Service and support
Contact Turner Hastings customer service for assistance with installation, operation, or troubleshooting.

Installing the timer

Carefully remove the back of the timer by placing a flat head screwdriver into the slots on the bottom of the unit and push to release.
Unplug the cable connector from the back of the timer screen.

Connect the Turner Hastings towel rail to the timer as seen in the below wiring diagram.

TURNER HASTINGS-TRTSB-7-Day-Programmable-Timer-1

Screw the back plate of the timer to the electrical plate.
Plug the cable connector into the back of the timer screen and connect the screen to the back of the timer.

User Interface

Portrait

Day indicator
Key lock icon
Schedule mode icon
Manual mode icon
ON/OFF indicator
Confirm settings
Program button
Mode button
Power button
Up & down arrows
Time

Landscape

Day indicator
Key lock icon
Schedule mode icon
Manual mode icon
ON/OFF indicator
Confirm settings
Program button
Mode button
Power button
Up & down arrows
Time

Setting the date and time

Press and the time will begin to flash
Use to select the correct time
Press until the day begins to flash
( Note: Monday is Day 1)
Use to select the correct day
Press to save the settings

Heating Modes

When the timer is on, press the to switch between manual and schedule modes.

Manual Mode
In manual mode press the to set the ON/OFF status.

Schedule Mode
In the schedule mode the timer will follow the heating schedule that is set. Refer to page 9 for programming instructions.

Advanced Settings

To access the advanced settings, turn the timer off by pressing

Press to display setting 01
Use the to adjust the settings
Press to cycle between setting 01 to 03
Press to save the settings

TURNER HASTINGS-TRTSB-7-Day-Programmable-Timer-8

Set up your heating schedule

Turn the timer on by pressing
To set up the heating schedule for Monday to Friday press
The time for P1 will flash. This is the first ON period for the day.

Use the to adjust the time to when the heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2.

Repeat above steps for P3 and P4 and then press (Note: P3 is turning the heated towel rail on in the evening and P4 is turning it off in the evening)
If the heated towel rail is only required to be on once a day set to OF for both P3 and P4 and ensure that the time set for P3 and P4 is after the time set for P2.

When Monday-Friday has been set press to go onto the Saturday and Sunday schedule.

The time for P1 will flash. This is the first ON period for Saturday and Sunday.

Use the to adjust the time to when the heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2.

Repeat above steps for P3 and P4

Turn the timer on by pressing
Change the menu option 02 to setting 02
(7 Day Program) as per instructions on page 8. The 7 day program option means that all 7 days are programmed to the same schedule or all 7 days are programmed individually.

Press until the day display flashes.
If programming all 7 days individually use the to select the day to program first.
If programming all 7 days to the same schedule,press and hold the button for about 5 seconds to select all 7 days.

To set up the heating schedule press
The time for P1 will flash. This is the first ON period for the day.

Use the to adjust the time the heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2

Repeat above steps for P3 and P4 and then press (Note: P3 is turning the heated towel rail on in the evening and P4 is turning it off in the evening)

If programming all 7 days to the same schedule, the program is now set up.

If programming all 7 days individually, press and use the to select the next day to program.

Factory Reset

Press to turn the timer off
Press and the hold until 04 is displayed
Press and hold for approx. 5 seconds will display on the screen and then the timer has been reset.
Turn the timer back on to setup the program

Temporary Override

Turning the timer onto a temporary override will allow the timer to be operated on manual until the next programmed period.
In schedule mode, press the and the ON/OFF display will flash.

Use to adjust the desired setting and Use press to adjust the desired setting and to confirm.

will be displayed below the ON/OFF display. To cancel the override setting press .

Holiday Mode

The Control Panel timer does not have a dedicated holiday mode. To suspend the heating schedule for a period of time turn the timer off using the button.

This will ensure the heating schedule is held and then to resume the heating schedule press the button.