PIPE DECOR 37024SB1 24 Inch Shelves With Straight Brackets Instruction Manual
- October 30, 2023
- PIPE DECOR
Table of Contents
PIPE DECOR 37024SB1 24 Inch Shelves With Straight Brackets
Product Information
The product is a shelving kit that comes in two variations: one with 24 shelves and the other with 36 shelves. The kit includes black pipes, flanges, caps, nipples, wood shelves, screws, and wall anchors. The shelves come in two sizes: 24 inches for the 24-shelf kit and 36 inches for the 36-shelf kit. The pipes and fittings are industrial-grade and coated with rust-preventive oil during manufacturing.
Product Usage Instructions
- Identify the type of kit you have: 24 shelves or 36 shelves.
- If a wall stud is present, attach the flange to the wall with the included screws. If no wall stud is present, use wall anchors.
- Assemble the pipes and fittings according to the included instructions.
- Place the wood shelves on top of the pipes and secure them in place with the included caps.
- If desired, clean and seal the pipes to prevent rusting. To clean the pipes, use warm water and dish soap until the rust-preventive oil is completely removed. Dry the pipes completely before sealing them.
- To seal the pipes, use a polyurethane matte or satin finishing spray or a finishing wax. Follow the instructions for your chosen sealing method and allow the pipes to dry completely before assembling the kit.
If you have any questions about assembling the kit or if you are missing pieces, email support@pipe-decor.com for assistance.
NEED HELP OR ADVICE ON PUTTING THIS KIT TOGETHER? MISSING PIECES?
EMAIL US AT SUPPORT@PIPE-DECOR.COM FOR ANY
QUESTIONS
(FOR 24” SHELVES)
PART | DESCRIPTION | QTY |
---|---|---|
A | CAP | 4 |
B | FLANGES | 4 |
C | 8” NIPPLE | 4 |
D1 | 24” WOOD SHELF | 2 |
E | 1 3/4” SCREWS & WALL ANCHORS | 16 |
(FOR 36” SHELVES)
PART | DESCRIPTION | QTY |
---|---|---|
A | CAP | 6 |
B | FLANGES | 6 |
C | 8” NIPPLE | 6 |
D2 | 36” WOOD SHELF | 2 |
E | 1 3/4” SCREWS & WALL ANCHORS | 24 |
- Place flange against the wall in the desired location and mark holes with a pencil
- Using a stud finder, locate and mark wall studs if found
- If a wall stud is present, attach the flange to the wall with included screws
- If no wall stud is present:
- Drill pilot holes in the wall using a ¼” drill bit
- Insert anchor fully into the pilot hole using a hammer and Phillips screwdriver as needed
- Attach the flange to the wall using included screws
HOW TO PREVENT PIPE CORROSION
PIPE DECOR industrial-grade black pipes and fittings are coated with rust- preventive oil during manufacturing. For best results, SEAL THE PIPES TO AVOID ANY RUSTING after cleaning the kit.
CLEAN AND SEAL INSTRUCTIONS
CLEAN: Recommended supplies: regular degreasing dish soap, washcloths, gloves (optional)
- Wash your pipes and fittings with warm water and dish soap until the oil is completely removed.
- Wipe the pipes with a dry washcloth and wait until the pipes are completely dry.
IMPORTANT: THE PIPES MUST BE COMPLETELY DRY BEFORE YOU START THE SEALING PROCESS.
SEAL:
if using polyurethane spray: Spray each dry pipe and fitting with a
polyurethane matte or satin finishing spray and let it dry before assembling
the kit. if using finishing wax: Coat each dry pipe with a finishing wax. Wait
for 20 minutes, then polish the pipe with a dry washcloth by wiping them down.
Faster wiping will result in a shinier finish.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>