Kalogiannis ME-150DH Hand Held Crimp Sealer User Manual

Kalogiannis ME-150DH Hand Held Crimp Sealer

Product Information

Hand Held Crimp Sealers 150DH

The Hand Held Crimp Sealers 150DH is a manual sealing device used for sealing various materials such as Cellophane, Wax Paper, Foils, Alluminium-Laminates and Heat Seal-able Labels. It is equipped with temperature controller, working light, and covered two 12 mm wide heated Jaws for constant heat. The Seal Jaws are PTFE coated and produce vertical line embossed seals. It has a power cord length of 3.0 meter and an aluminum mesh safety guard.

Construction Diagram and Parts List

The Hand Held Crimp Sealers 150DH consists of Upper Lever Body, Lower Lever Body, Upper Sealer Jaw, Ceramic Pads, Clips for Sealer Jaw, Bolt Pin & Screw, Power Indication Lamp, Temp. Controller & Switch, Heater, Return Spring, Power Plug, Fixed Plates for Heater, Metal Plate for Protection, Sealer PTFE Cloth, Sealer Rubber, Rubber Holder, Lead Wire, and Fiber Washer.

Operating Instructions

1. Connect the device to a properly grounded outlet only.
2. Turn on the device and wait for it to heat up to the desired temperature.
3. Place the material to be sealed between the Seal Jaws and close the Upper Lever Body onto the Lower Lever Body.
4. Hold the Upper Lever Body down firmly until the seal is complete.
5. Release the Upper Lever Body and remove the sealed material from the Seal Jaws.
6. Repeat the process for additional seals.

Please read before use

Thank you for purchasing the hand held crimp sealer 150DH.

• Please read this instruction carefully before use.
• Please keep this manual on file as reference book and for troubleshooting

Safety advice

• To prevent damage of the device and inju- ries of the operator, it is absolutely neces- sary to comply the safety notes in this manual.
• The mentioned warnings describe possible injuries and damages, which are due to wrong usage or maintenance of the device.

Please read and follow these safety notes before reading the manual.

CAUTION:

1. To reduce the risk of shock, disconnect the unit from the supply circuit before servicing the replacement of the heating element.
2. To provide continued protection against risk of electric shock, connect to properly grounded outlet only.
3. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufac ture or its service agent.

WARNING:

1. A live heating element is located in the jaw under the PTFE cloth. Use caution during operation.
   DO NOT TOUCH THE ELEMENT!

2. For continued protection against fire or electric shock, replace only with type cartridge and suitable ampere fuse, provided in legible adjacent to fuse holder.

3. Close supervision is required when the product is used near children.

Helpful information

1. Always keep the sealing platform clean. Particular care „should“ be taken to remove any redidue from the Seal Jaws.
2. Do not clean the sealing platform with anything wet.
3. Occasionally check the condition both sides of the heater jaws. a poor sealer platform will effect the quality of your seal.
4. Never touch to heater jaws for high temperature.
5. USE ONLY GENUINE REPLACEMENT PARTS.

Construction diagram

Parts list

No| Description| Parts- No| No| Description| Parts- No
---|---|---|---|---|---
1| Upper Lever Body| 1A10-

7006

| 10| Return Spring| 1E10-

7005

2| Lower Lever Body| 1A10-

7007

| 11| Power Plug| 1E30-

1005

3| Upper Sealer Jaw| 2B40-

7001

| 12| Fixed Plates for Heater| 1C40-

7006

4| Ceramic Pads| 1J40-

7001

| 13| Metal Plate for Protection| 1C10-

7004

5| Clips for Sealer Jaw| 1C40-

7005

| 14| Sealer PTFE Cloth| 1J50-

3115

6| Bolt Pin & Screw| 1D20-

7005

| 15| Sealer Rubber| 1G20-

1010

7| Power Indication Lamp| 1E40-

7005

| 16| Rubber Holder| 1C10-

7005

8| Temp. Controller & Switch| 1E60-

7005

| 17| Lead Wire| 1E30-

7002

9| Heater| 1E60-

7005

| 18| Fiber Washer| 1J30-

7002

Benefits

1. constant heat for Cellophane & Foil
2. covered two 12 mm wide heated Jaws for Cellophane, Wax Paper, Foils, Alluminium-Laminates and Heat Seal-able Labels.
3. light weight and easy to grip
4. equipped with temperature controller and working light
5. PTFE coated Seal Jaws
6. vertical line embossed seal
7. the power cord length is 3.0 meter
8. aluminium mesh safety guard

Elektronischer Schaltplan

Operating instructions

1. Connect power supply plug to AC outlet, the Power light appears indicating power to the unit.
2. Turn on main temperature knob. Heating light appears, adjust the temp. control knob to the 100°C suitable scale fo thickness and material of bag. The heating light will go off about three minutes, it is the heating time.
3. Adjust the temperature knob to suitable scale for sealing material.
4. Insert bag into the seal jaws and apply squeeze the lever handle to seal the bag.
5. Release the handle and remove the sealed bag.
6. If it does no complete with the seal, turn the temp. knob add until you get desired seal.
7. Turn off machine when not in use. Allow the sealer to cool down for 10 minutes before storing.

The temperature controller is calibrated in centigrade to convert to fathrenheit.(°Cx8/5 +32=°F)
For safety keep hands and fingers away from the jaws or hex nuts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>