DSI LIGHTING HD7183A 1-Light Pendant Instruction Manual

October 30, 2023
DSI LIGHTING

DSI-LIGHTING-LOGO

DSI LIGHTING HD7183A 1-Light Pendant

DSI-LIGHTING-HD7183A-1-Light-Pendant-PRODUCT

Product Information

  • Item #: 000 000 0000
  • Model #: HD7183A
  • Product Name: 1-Light Pendant
  • Manufacturer: Design Solutions International
  • Warranty: Three (3) year warranty

Product Usage Instructions

  1. Read and save the instructions before attempting to assemble, install or operate the product.
  2. Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Contact the Customer Service Team at 1-800-388-6141 ext 216 or email at Customer Support@DSILighting.com for assistance.
  3. Before starting installation or removing a previous fixture, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.
  4. Use a voltage tester to ensure the wire is not live before touching any wire.
  5. When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch the plug fuse only by its insulated rim. Remove the cartridge fuses with a fuse puller.
  6. Use tools with insulated handles and ladders made of wood or fiberglass.
  7. To protect children, place a safety cover over any unused outlets.
  8. If you have any electrical questions, consult a qualified electrician. For non-electrical questions about the fixture, contact the Customer Service Team at 1-800-388-6141 ext 216 or email CustomerSupport@DSILighting.com.

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

  • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install, or operate this product. Failure to do so could lead to electrical shock, fire, or other injuries that could be hazardous or even fatal.
  • Before touching any wire, use a voltage tester to make sure it is not live.
  • When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch the plug fuse only by its insulated rim. Remove the cartridge fuses with a fuse puller.
  • Use tools with insulated handles and ladders made of wood or fiberglass.
  • To protect children, place a safety cover over any unused outlets.
  • DANGER: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.
  • CAUTION: CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS. If you have any non-electrical questions about this fixture, please call our Customer Service Team at 1-800-388-6141 ext 216. Please reference item (000 000 0000) or UPC (802513198676).

Warranty

THREE (3) YEAR WARRANTY
WHAT IS COVERED
The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear
WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product
Contact the Customer Service Team at 1-800-388-6141 ext 216 Eastern Time, Mon- Fri 9:30 am to 3:00 pm EST. For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com.

Pre-Installation

PLANNING INSTALLATION

  • Read all the instructions before installing.
  • To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.
  • IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call the Customer Service Team at 1-800-388-6141 ext 216. For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com.
  • NOTE: This product requires one 60W maximum medium base (E26) type “S” or type “A” or 9W maximum medium base (E26) self-ballasted LED vintage Edison bulbs (sold separately).

TOOLS RECOMMENDED

(NOT INCLUDED)DSI-LIGHTING-HD7183A-1-Light-Pendant-
FIG-1

HARDWARE INCLUDED

NOTE: Hardware is not shown to actual size.DSI-LIGHTING-HD7183A-1
-Light-Pendant-FIG-2

Part Description Quantity
AA Crossbar assembly 1
BB Outlet box screw 2
CC Wire connector 3
DD Quick link 2
EE Ceiling canopy 1
FF Fixture chain 1

PACKAGE CONTENTS

DSI-LIGHTING-HD7183A-1-Light-Pendant-
FIG-3

Part Description Quantity
A Fixture loop 1
B Fixture body 1

Installation

  1. Installing the crossbar assembly
    Secure the crossbar assembly (AA) to the outlet box (not included) with the outlet box screws (BB). Tighten until snug.

    • NOTE: The preassembled mounting nipple on the crossbar should protrude outward.
  2. Test fitting the ceiling canopy to the crossbar assembly

    • Remove the pre-assembled canopy lock ring from the crossbar assembly (AA).
    • Temporarily attach the ceiling canopy (EE) to the pre-assembled nipple on the crossbar assembly (AA).
    • Secure with the canopy lock ring (1).
    • NOTE: If the ceiling canopy is not snug against the ceiling, remove it from the crossbar assembly and adjust the length of the pre-assembled nipple by unscrewing the pre-assembled hex nut.
      Screw the nipple in or out of the crossbar until the correct length is achieved. Then, re-attach the ceiling canopy.
  3. Installing the fixture chain

    • Guide the fixture wire with bare copper ground wire through the fixture loop (A), and screw the fixture loop (A) onto the top of the fixture body (B) securely.
    • Choose desired hanging length for the light fixture. Suggested mounting height over a table or island is 30 inches from the table/island top to the bottom of the fixture. Adjust the fixture chain (FF) to the desired length, removing links if necessary.
    • Connect one end of the fixture chain (FF) to the canopy chain loop preassembled to the crossbar assembly (AA) with one quick link (DD).
    • Connect the other end of the fixture chain (FF) to the fixture loop (A) with the remaining quick link (DD).
    • Suggested chain length to hang fixture 30 inches above table top:
    • 8- ft. ceiling : 10 in. of chain + 2 quick links
    • 9- ft. ceiling: 22 in. of chain + 2 quick links
    • 10- ft. ceiling: 34 in. of chain + 2 quick links
    • 11- ft. ceiling: 46 in. of chain + 2 quick links
    • 12- ft. ceiling: 58 in. of chain + 2 quick links
    • NOTE: You may need to use pliers (not included) to open the links of the fixture chain (FF). If so, put a cloth over the fixture chain (FF) to protect the finish from the pliers.
  4. Pulling the supply wires

    • Pull the supply wires and ground wire up through the fixture chain alternating links.
    • Push the ends of the supply wires and ground wire up through the canopy chain loop and into the outlet box. The remaining slack wire will be inserted into the outlet box in STEP 6.
    • NOTE: To make the next step easier, cut the supply wire and ground wire 24 inches longer than the distance from the fixture loop to the ceiling. Important: Please pay attention to the polarity (wires labels L & N) when cutting wires. Wire identification will be needed in STEP 5.
  5. Trimming excess fixture wire

    • Unthread the canopy lock ring.
    • Slide the canopy lock ring and the ceiling canopy (EE) down the quick link (DD).
    • Push all slack fixture wire through the canopy chain loop and into the outlet box.
    • Trim excess fixture wire leaving a minimum of 6 inches hanging out of the outlet box.
    • Separate the smooth side and ribbed side of the supply wire to about 3 inches from the end.
    • Using wire strippers, strip each wire ½ inch from the end.
  6. Making the electrical connections

    • Use wire connectors (CC) to connect the wires. Ground wire:
    • Wrap the supply ground wire around the green ground screw on the crossbar assembly (AA), no less than 2 in. from the end of the wire. Tighten ground screw.
    • Connect the fixture ground wire to the supply ground wire with the wire connector (CC).
    • Supply wire:
    • Connect the house white wire to the fixture supply wire (ribbed sided) from fixture identified with the label “N”.
    • Connect the house black (or red) wire to the fixture supply wire (smooth side) from fixture identified with the label “L”.
    • Wrap each connection with approved electrical tape and carefully insert all of the connected wires into the outlet box.
  7. Installing the ceiling canopy

    • Attach the ceiling canopy (EE) back over the canopy chain loop.
    • Secure with the canopy lock ring.
  8. Installing the light bulb

    • Install the correct bulb (not included) referring to fixture markings and/or labels for maximum wattage.
    • NOTE: Uses one 60W maximum medium base (E26) type “S” or type “A” or 9W maximum medium base (E26) self-ballasted LED vintage Edison bulbs (sold separately).

Care and Cleaning

  • Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
  • To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box, and use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.

Troubleshooting

Problem Possible Cause Solution
The light(s) will not turn on. The bulb is burned out. Replace the light

bulb.
The power is off.| Ensure the power supply is turned on.
There is a faulty switch.| Test or replace the switch.
There is a faulty wire connection.| Check the wiring.
The fuse blows or the circuit breaker trips when the light is turned on.| There are crossed wires or the power wire is grounding out.| Discontinue use of the light. Check the wire connections. Contact a qualified electrician or call the Customer Care Service Team at 1-800-388-6141 ext 216. For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com.

Service Parts

MODEL: HD7183ADSI-LIGHTING-HD7183A-1-Light-Pendant-
FIG-12

Part Description
AA Crossbar assembly
BB Outlet box screw
CC Wire connector
DD Quick link
EE Ceiling canopy
FF Fixture chain
A Fixture loop
B Fixture body
  • Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service
  • Mon-Fri 9:30 am to 3:00 pm EST
  • 1-800-388-6141 ext. 216
  • For customer service support and the fastest response, please email us atCustomerSupport@DSILighting.com
  • Retain this manual for future use.

Documents / Resources

| DSI LIGHTING HD7183A 1-Light Pendant [pdf] Instruction Manual
HD7183A 1-Light Pendant, HD7183A, 1-Light Pendant, Pendant
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals