Shenzhen Baishiyue Electronice BSY-DESVIEW Universal Wireless VR Remote and Gamepad User Manual
- June 4, 2024
- Shenzhen Baishiyue Electronice
Table of Contents
Shenzhen Baishiyue Electronice BSY-DESVIEW Universal Wireless VR Remote
and Gamepad
introduction
Many thanks, tor purchasing our product! This is a portable wireless
controller, used for mobile phones, MID, TV boxes, smart TV, PC, and so on.lt
can be used as a gamepad, VR
remote, wireless mouse, music control, E-book page, PPT presentation, etc. and
Support OSAndroid, Windows, and so on.
Important Note: Products are subject to change without any notice.
operating instructions:
-
Power On: Press/the button until LED is on (about 2 seconds).( First put the batteries)
Power Off: Press the button until LED is off (about 5 seconds).
Note: If no connection with the wireless device after 5mins, the system will power off automatically; after connecting with a wireless device, if no any operation, the system will power off after 30mins. -
Pair and connect: after power on, the LED indicator will flash, and the device will enter into the wireless pair mode automatically to find the address and name of this device
(Desview), Click then can connect. Pair and connect successfully, LED indicator will turn of.Next power on, it can connect and pair the last Wireless device.
Unpair: In the turn-off state, press (over 8 seconds), LED will flash, then go to pair mode again, and can’t connect last paired device -
Boot mode (factory default Android mode): Android (-B mode): The handle is in the off state, press and hold the B button, and press the button to turn on, and the wireless name Desview will be displayed. ios (-X mode): The handle is in the off state, press and holds the X button, and press and hold the Power button to turn on, and the
wireless name Desview will be displayed. -
Battery: our product needs two 1.5V batteries of type size AAA, when power is low, LED will| flash, please change the batteries.
Product Specifications
| Item | Specifications |
|---|---|
| Model | Desview |
| Size | 100mm x40mm x 24mm |
| Wireless Protocol | Wireless 4.2 compliant |
| Wireless Distance | 2-10 Meters |
| OS | Android /ios/Pc |
| CPU | 32Bit RISC-v Core |
| Battery | Type size alkaline AAA 1.SV x 2 |
| Working time (Continuous game) | About 300 hours |
| Work current | 0.S-3mA |
| Shutdown current | <9uA |
Notes:
- When an accident causes not to boot or is unable to shut down, please use a needle to take out the bat-teries.
- When the pairing is abnormal or the wireless name cannot be found, turn off the handle, press and hold the Power button for more than 8 seconds, the light flashes and then release, cancel and ignore all wireless pairing on the device (including earphone bracelet, etc.), andre-pair .
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur ina particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.