Topway Display LMT035DNJFWD-1 LCD Module User Manual

October 30, 2023
Topway Display

Topway Display LMT035DNJFWD-1 LCD Module LOGO

Topway Display LMT035DNJFWD-1 LCD Module

Topway Display LMT035DNJFWD-1 LCD Module product

Product Information

The LMT035DNJFWD-1 is an LCD module that provides high-quality display technology with a screen size of 3.5 inches (diagonal). The module has a color depth of up to 262K colors and a resolution of 320×240 pixels. The active area of the module is 70.08mm x 52.56mm, and the dot pitch is 0.219mm x 0.219mm. The display mode is transmissive, and the pixel configuration is RGB vertical stripe.
The viewing direction is 6 o’clock, and the polarizer surface treatment is anti-glare. The backlight type used in this module is a white LED backlight. The outline dimension of the module is 76.9mm x 63.9mm x 3.2mm (max).

Product Usage Instructions

To use the LMT035DNJFWD-1 LCD module, please follow these instructions:

Basic Specifications

  • Scree n Size(Diagonal) :  3.5”
  • Color Depth: 65K/262K Color
  • Number of dots :  320(RGB)x480
  • Active Area : 48.96×73.44mm
  • Dot Pitch :  0.153×0.153mm
  • Display Technology :  a-Si TFT active matrix
  • Display Mode :  Transmissive With Normally white
  • Pixel Configuration :  RGB Vertical Stripe
  • Viewing Direction :    12H (1) (gray scale inverse)             6H (2)
  • Polarizer Surface Treatment:    HC
  • Backlight Type:        LEDs
  • Outline Dimension :    55.26x 84.69 x 2.2 mm    (exclude FPC , see dwg for details)
  • Operating Temperature :    – 20 ~ +70°C (No Condensation)
  • Storage Temperature :    – 30 ~ +80°C (No Condensation)

Note :

  • For saturated color display content (eg. pure-red, pure-green, pure-blue or pure-colors-combinations).
  • For “color scales” display content.
  • Color tone may slightly change by temperature and driving condition.
Block Diagram

Topway Display LMT035DNJFWD-1 LCD Module 1

Terminal Functions
Pin No. PIN Name I/O Descriptions
1 VSS Power Negative power supply,0V
2,3 IOVDD Power IO Positive Power
4,5 VDD Power Positive power supply
6 IM0 Input MPU system interface mode select
7 IM1 Input MPU system interface mode select
8 IM2 Input MPU system interface mode select
9 RESX Input Reset signal

RESX = L, Initialization is executed RESX = H, Normal running.
10| VSYNC| Input| Vertical sync. signal in RGB mode
If no used, please connect this pin to VSS
11| HSYNC| Input| Horizontal sync, signal in RGB mode
If no used, please connect this pin to VSS
12| PCLK| Input| Pixel clock signal in RGB mode
If no used, please connect this pin to VSS
13| DE| Output| Data enable signal in RGB mode
If no used, please fix this pin at VSS level
14| DB17/R5,Msb| I/O| Data Bus
15| DB16/R4| I/O
:| :| :
18| DB13/R1| I/O
19| DB12/R0,Lsb| I/O
20| DB11/G5,Msb| I/O
21| DB10/G4| I/O
:| :| :
24| DB7/G1| I/O
25| DB6/G0,Lsb| I/O
26| DB5/B5,Msb| I/O
27| DB4/B4| I/O
:| :| :
30| DB1/B1| I/O
31| DB0/B0,Lsb| I/O
32| VSS| Power| Negative power supply,0V
33| DOUT| Output| Serial data output pin
If no used, leave this pin open
34| SDA| I/O| serial data input /output bi-direction pin
35| RDX| Input| serve as a read signal
36| WRX_SCL| Input| (WR) Write data enable pin in DBI Type B (SCL) Write data enable pin in DBI Type C
If no used, please connect this pin to IOVDD
37| DCX| Input| Data/Command Selection pin Low: Command
High: Parameter
38| CSX| Input| Chip select signal
If no used, please connect this pin to IOVDD
39| NC(XR)| ****

|
40| NC(YD)| No connect
41| NC(XL)
42| NC(YU)|
43| LEDA| Power| LED ANODE
44~49| LEDK| Power| LEDK CATHODE
50| VSS| Power| Negative power supply,0V

Topway Display LMT035DNJFWD-1 LCD Module 41

Absolute Maximum Ratings

Items Symbol Min. Max. Unit Condition
Power Voltage VDD -0.3 +3.6 V VSS = 0V
Input Voltage VIN -0.3 +3.6 V VSS = 0V
Operating Temperature TOP -20 +70 °C No Condensation
Storage Temperature TST -30 +80 °C No Condensation

Cautions:
Any Stresses exceeding the Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.

Electrical Characteristics

DC Characteristics

Items| Symbo l| MIN.| TYP.| MAX.| Unit| Condition / Application Pin
---|---|---|---|---|---|---
Operating Voltage| VDD| 2.65| 3.0| 3.6| V| VDD,IOVDD
Input High Voltage| VIH| 0.7xVDD| –| VDD| V| IM0~IM2,RESX,VSYNC,HSY NC,PCLK,DB17/R5,Msb, DB16/R4~DB13/R1 ,DB12/R0,Lsb,DB11/G5,Msb, DB10/G4~DB7/G1 ,DB6/G0,Lsb,DB5/B5,Msb, DB4/B4~DB1/B1,DB0/B0,Lsb, SDA,RDX,WRX_SCL,DCX, CSX,
Input Low Voltage| VIL| -0.3| –| 0.3xVDD| V
Output Low Voltage| VOL| 0| –| 0.99| V| DB17/R5,Msb, DB16/R4~DB13/R1 ,DB12/R0,Lsb,DB11/G5,Msb, DB10/G4~DB7/G1 ,DB6/G0,Lsb,DB5/B5,Msb, DB4/B4~DB1/B1,DB0/B0,Lsb, DE,SDA,DOUT
Operating Current| IDD| –| 8| –| mA| VDD (*1)

Note: *1. VDD=3.0V

LED Backlight Circuit Characteristics

Items| Symbol| MIN.| TYP.| MAX.| Unit| Remark
---|---|---|---|---|---|---
Forward Voltage| Vf| –| 3.2| –| V| For each LED
Forward Current| If| –| 20| –| mA| For each LED
LED lifetime| –| –| 30000| –| Hours|

Note1: LED CIRCUIT DIAGRAM
Note 2: LED: VF =3.2V, IF =20mA(TYP)
Note 3 :IF is defined for one LED.
Optical performance should be evaluated at Ta=25℃ only.
If LED is driven by high current, high ambient temperature & humidity condition.
The life time of LED will be reduced. Operating life means brightness goes down to 50% initial brightness.
Typical operating life time is estimated data.
Note 4: Under LCM operating, the stable forward current should be inputted. And forward voltage is for reference only.

AC Characteristics

DBI Type B

DBI Type B Timing Characteristic

Topway Display LMT035DNJFWD-1 LCD Module 3
Topway Display LMT035DNJFWD-1 LCD Module 42
Topway Display LMT035DNJFWD-1 LCD Module 43 DBI Type B Data Bus
8-bit Data Bus for 16-bit/pixel (RGB 5-6-5 Bits Input), 65K-color

Topway Display LMT035DNJFWD-1 LCD Module 7 Topway Display LMT035DNJFWD-1 LCD Module 88-bit Data Bus for 18-bit/pixel (RGB 6-6-6Bits Input), 262 K-color
Topway Display LMT035DNJFWD-1 LCD Module 9

Topway Display LMT035DNJFWD-1 LCD Module 10 9-bit Data Bus for 18-bit/pixel (RGB 6-6-6Bits Input), 262 K-color
Topway Display LMT035DNJFWD-1 LCD Module 11 16-bit Data Bus for 16-bit/pixel (RGB 5-6-5 Bits Input), 65K-color
Topway Display LMT035DNJFWD-1 LCD Module 12 16-bit Data Bus for 18-bit/pixel (RGB 6-6-6Bits Input), 262 K-color
Topway Display LMT035DNJFWD-1 LCD Module 13 18-bit Data Bus for 18-bit/pixel (RGB 6-6-6Bits Input), 262 K-color
Topway Display LMT035DNJFWD-1 LCD Module 14

3-Line SPI Interface Timing Characteristic

Topway Display LMT035DNJFWD-1 LCD Module 15
Topway Display LMT035DNJFWD-1 LCD Module 16

4-Line SPI Interface Timing Characteristic

Topway Display LMT035DNJFWD-1 LCD Module 17
Topway Display LMT035DNJFWD-1 LCD Module 18Note:Ta=-30 to 70℃,IOVDD,VDD=2.5V to 3.3V,VSS=0V,T=10+/-0.5ns. Please refer to IC: ILI9488 data sheet for more details.

DPI Interface

DPI Interface CharacteristicTopway Display LMT035DNJFWD-1 LCD Module
19
Topway Display LMT035DNJFWD-1 LCD Module 20 DPI Interface pixel format

Topway Display LMT035DNJFWD-1 LCD Module 21The Pixel clock (DCLK) runs all the time without stop. It is used to enter VS, HS, DE and D[17: 0] states when there is a rising edge of the DCLK. The DCLK cannot be used as the internal clock for other functions of the display module.
Vertical synchronization (VS) is used to indicate when a new frame of the display is received. This is low enable and its state is read to the display module by a rising edge of the DCLK signal.
Horizontal synchronization (HS) IS used to indicate when a new line of the frame is received. This is low enable and its state is read to the display module by a rising edge of the DCLK signal.
Data Enable (DE) is used to indicate when the RGB information that should be transferred in the display is received. This is a high enable, and its state is read to the display module by a rising edge of the DCLK signal. D[17:0] is used to indicate what is the information of the image that is transferred on the display (when DE = 0 (low) and there is a rising edge of DCLK). D[17:0] can be 0(low) or 1(high). These lines are read by a rising edge of the DCLK signal. In RGB interface modes, the input display data is written to GRAM first then outputs the corresponding source voltage according to the gray data from GRAM.
Note:Please refer to IC: ILI9488 data sheet for more details.
DPI(RGB) Interface timing
Topway Display LMT035DNJFWD-1 LCD Module 22
Topway Display LMT035DNJFWD-1 LCD Module 23
Topway Display LMT035DNJFWD-1 LCD Module 24

Power ON/OFF Sequence

Topway Display LMT035DNJFWD-1 LCD Module 25Notes:

  1. There are not any abnormal visual effects when one power mode changes to another power mode.
  2. There is not any limitation, which is not specified by users, when one power mode changes to another power mode.

IOVDD and VDD can be applied or powered down in any order. During the Power Off sequence ,if the LCD is in the Sleep In mode, VDD and IOVDD must be powered down with a minimum of 120 msec.If the LCD is in the Sleep In mode, VDD and IOVDD can be powered down with a minimum of 0msec after the /RST has been released. /CS can be applied at any time or can be permanently grounded. /RST has priority over /CS.
Notes:

  1. There will be no damage to the ILI9488 if the power sequences are not met.
  2. There will be no abnormal visible effects on the display panel during the Power On/Off Sequence.
  3. There will be no abnormal visible effects on the display between the end of the Power On Sequence and before receiving the Sleep Out command, and also between receiving the Sleep In command and the Power Off Sequence.
  4. If the /RST line is not steadily held by the host during the Power On Sequence as defined in Sections 11.1 and 11.2 ( ILI9488 datasheet ), then it will be necessary to apply the Hardware /RST after the completion of the Host Power On Sequence to ensure correct operations. Otherwise, all the functions are not guaranteed.
  5. When the power is turned on, the climb period timing (Trise) must be greater than 10us.
  6. Keep data pins D[17:0] at low level, or IOVDD comes laterTopway Display LMT035DNJFWD-1 LCD Module 26
Reset timing

Topway Display LMT035DNJFWD-1 LCD Module 27

Item Symbol MIN. TYP. MAX. Unit
Reset LOW pulse width tRW 1.0 us
Reset time TRT 120 ms

Note:Please refer to IC: ILI9488 data sheet for more details.

Optical Characteristics

Topway Display LMT035DNJFWD-1 LCD Module 44 Note 1: Detinition ot optical measurement system.
The optical characteristics should be measured in dark room. After 5 Minutes operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring the center area of the panel.
Topway Display LMT035DNJFWD-1 LCD Module 28 Note 2: Definition of viewing angle range and measurement system.
viewing angle is measured at the center point of the LCD by CONOSCOPE(ergo-80).
Topway Display LMT035DNJFWD-1 LCD Module 29 Note 3: Definition of contrast ratio
Topway Display LMT035DNJFWD-1 LCD Module 30 “White state”: The state is that the LCD should drive by white.
“Black state”: The state is that the LCD should drive by black.
white: To be determined black: To be determined.
Note 4: Definition of Response time
The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (ToN) is the time between photo detector output intensity changed from 90% to 10%. And fall time (Torr) is the time between photo detector output intensity changed from 10% to 90%
Topway Display LMT035DNJFWD-1 LCD Module 31 Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area.
Topway Display LMT035DNJFWD-1 LCD Module 32Lmax: The measured Maximum luminance of all measurement position.
Lmin: The measured Minimum luminance of all measurement position.
Note 7: Definition of Luminance:
Measure the luminance of white state at center point.

Inspection Condition

Unless otherwise stated,all the inspections are carryout under the following condition

No. Items Conditions
1 Lighting Illumination: Appearance 300-700Lux
2 Inspection Distance 30-40cm form the test sample,within normal viewing

angle
3| Temperature| Room Temperature (25 ºC), no condensation
4| Viewing Angle| U/D: 45º/45º, L/R: 45º/45º
5| Inspection Time| 15 seconds
6| Defect Allowance| Under 5.0” (include 5.0”): 3
5.0” to 7.0”: 4
Above 7.0”: 6

Display Pattern
No. Items /Contents Type Standard Judgment
CR MA MI
1 No Display/Unstable Display
2 Line defect
3 Display abnormally
4 Function Defective
5 Glass Crack
6 Spot Defect Including:
Black spot, White spot, Foreign particle, Polarizer dirt, Cell particle
Under 5.0” (include 5.0”) 5
(a+b)/2≤0.15 Allowed
0.15<(a+b)/2≤0.25 3 max.
(a+b)/2>0.25 Not Allowed

Above 5.0” 5
(a+b)/2≤0.25| Allowed
0.25<(a+b)/2≤0.5| 3 max.
(a+b)/2>0.5| Not Allowed
7| Line Defect Including: Black line, White line, ScratchTopway Display
LMT035DNJFWD-1 LCD Module 34| | | √| Under 5.0” (include 5.0”)
---|---|---|---|---|---
a≤0.03| Allowed
0.03<a≤0.05 and b≤5.0| 2 max.
a>0.05 or b>5.0| Not Allowed
Above 5.0”
a≤0.03| Allowed
0.03<a≤0.05 and b≤5.0| 4 max.
a>0.05 or b>5.0| Not Allowed
8| Polarizer Dent/Bubble| | | √| Under 5.0” (include 5.0”)
(a+b)/2≤0.25| Allowed
0.25< (a+b)/2≤0.5| 3 max.
(a+b)/2>0.5| Not Allowed
Above 5.0” 5
(a+b)/2≤0.25| Allowed
0.25< (a+b)/2≤0.5| 3 max.
(a+b)/2>0.5| Not Allowed
9| Bright dot defect| Topway Display LMT035DNJFWD-1 LCD Module
36| | | √| Under 5.0” (include 5.0”)| 0 max.
5.0” to 7.0”| 2 max.
Above 7.0”| 3 max.
3 consecutive dots| Not Allowed
10| Dark dot defect| Topway Display LMT035DNJFWD-1 LCD Module
37| | | √| Under 5.0” (include 5.0”)| 2 max.
5.0” to 7.0”| 4 max.
Above 7.0”| 5 max.
3 consecutive dots| Not Allowed
11| Bright dot defect + Dark dot defect| | | √| Under 5.0” (include 5.0”)| 2 max.
5.0” to 7.0”| 4 max.
Above 7.0”| 5 max.
12| FPC or FFC broken FPC/FFC| | √| | —| Not Allowed
13| PCBA defect PCBA| | √| | Refer to IPC-A-610 IPC-A-610| —

Quality Level and Sampling
Items Standard
Sampling Standard MIL-STD-105E
Sampling Level
AQL level MA: AQL=0.65 MI: AQL=1.0
Handling Precaution
  1. Never attempt to disassemble or rework LCD module

  2. Never let LCD module contact with liquids

  3. LCD module can be easily damaged by electrostatic charge.
    Please maintain an optimum anti-static working environment.

  4. LCD panel is made with glass.
    Any mechanical shock (eg. Vibration, distortion, extrusion, impact,drop) will damage the LCD module

  5. Avoid showing a display pattern on screen for a long time (continuous ON segment)

  6. The color and evenness of the display may slightly vary with the temperature

  7. Signal and Power supply excess the operation range may damage the LCD module

  8. Avoid touching the LCD surface to prevent any scratch on its surface

Packing Drawing

Per Carton
Topway Display LMT035DNJFWD-1 LCD Module 45
Topway Display LMT035DNJFWD-1 LCD Module 38
Topway Display LMT035DNJFWD-1 LCD Module 39

Note :

  1. LCD Display Type : TFT.Transmissive

  2. Pixel Arrangment • RGB-STRIPE

  3. Color Depth : 262k Color

  4. Operating Voltage‹VDD , IDVDD> : 3.0V

  5. Backlight : White LEDs

  6. Backlight Supply : 6×20mA (VF=3.2V, TYP)

  7. Recommended Connector K1 FH19SC-50S-0.5SHCHIROS> Or Equivalent

  8. Operating
    Temperature : -20°C~70°C

  9. Storage
    Temperature: -30°C~80°C

Note: Please keep the operating temperature of the module between -20°C to 70°C and the storage temperature between -30°C to 80°C. The color tone of the display may slightly change by temperature and driving condition.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals