MOTINOVA CS520 Series Cycle Computer Controller Instruction Manual

MOTINOVA CS520 Series Cycle Computer Controller

Please read this instruction thoroughly before using the product and keep it well.

INSTALLATION INSTRUCTION

Step 1:
Fixing cycle computer controller to the left handle bar and display to the middle of handle bar, and adjusting them to the proper position and viewing angle.

Step 2:
Following the below picture to install the screw, and suggesting to use 2N.m – 2.5N.m torque to tighten. ( Instrument damaged by over-locking is not promised to get warranty service.)

PRODUCT INTRODUCTION

1. Battery capacity

2. Power mode

3. Speed

4. Endurance mileage

5.  Total mileage

6. Current mileage

7. Unit

8. Power level

9. Time

10. ( Bicycle light indication

11. Power button

12. + button

13. ” – ” button

14. Walk assist button

15. Setting button

16. Bicycle light button

OPERATION

• Shift Up the Gear Level
  Short pressing the “+” button.

• Shift Down the Gear Level
  Short pressing the “-” button.

• Settings
  Long pressing (more than 1.55) the “Setting” button to enter.

• Light On/Off
  Short pressing the “Light” button.

• Power On
  Pressing “Power” button for 1s.

• Power Off
  Short pressing the “Power” button.

Walk Mode
Under Walk mode, the Walk mode icon displays on the right corner. The system will provide within the power 6 km/h.

1. Click WALK button to enter Walk mode enquiry, the Walk mode icon displays and the “+” sign on the icon flashes.
2. Long pressing “+” button, the “+” icon on the display stop flashing and the system outputs power; when loosing “+” button, the system stops providing power and the “+” icon on the display flashes again.
3. Under Walk mode, if you do not press “+” button at 3s, the motor will exit the Walkmode automatically, and the interface will be restored to the previous Power mode.
   You can also click any button (excluding “+” button) to exit the Walk mode automatically, and the interface will be restored to the previous Power mode.
   Under Walk mode, the Power mode will not be displayed.

Shift to show continuable / Current / Total trip
Short pressing the “Setting” key.

ASSIST LEVEL

• 6 Levels
  OFF, ECO, NORM, SPORT, TURBO, SMART.

• Default Level
  Level OFF, without power output.

CYCLE COMPUTER SETTING INSTRUCTION

Time Setting:
System time can be adjusted. Operations as below:

1. When speed is 0, long pressing “Setting” button for over 1.5s to enter setting interface.
2. After entering setting interface, click “+” button or”” button to select “hour” or “minute”, then pressing “Setting” button to confirm, the value of “hour” or “minute” flashes.
3. Pressing “+” or “.” button to adjust the value, click “Setting” button to save. After the adiustment is completed, short pressing the “Setting” button to save, or long pressing the “Setting” button for over 1.5s to save and exit the settings interface.

Unit Setting:
Speed and mileage unit can be adjusted. You can choose km or mile in setting. When the speed unit changes, the mileage unit changes accordingly. Operations as below:

1. When the speed is 0, pressing the “Setting” button for over 1.5s to enter the setting interface.
2. After entering the setting interface, pressing the “+” button or “.” button box to select the “unit”, and then click the “Setting button to confirm, the selected unit flashes.
3. Then pressing the “+” button or “-“ button to adjust the unit. After the adjustment is completed, short pressing the “Setting button to save, or long pressing the “Setting” button for over 1.5s to save and exit the settings interface.

Clear Setup:
The subtotal mileage can be cleared, while total mileage cannot be cleared.

Operations as below:

1. When the speed is 0, long pressing “Setting” button for over 1.5s to enter the setting interface.
2. After entering the setting interface, click the “+” button or “” button to select the subtotal mileage, and then click the “Setting” button to confirm, the subtotal mileage value flashes.
3. Then long pressing “ – ” button for over 1.5s to clear the value (this operation is irrevocable). After the adjustment is completed, short pressing the “Setting” button to save, or long pressing the “Setting” button for over 1.5s to save and exit the setting interface.

Backlight brightness setting:
After entering the backlight setting interface, click “Setting” button to enter the setting state (at this time, the value will flash continuously), click “+” or “ – ” button to select the brightness from Level 1 to Level 5, and then click “Setting” button to confirm the setting.

Automatic power-off time setting:
After entering the setting interface of automatic power-off time, click “Settings” button to enter the setting state (at this time, the value will flash continuously), click “+” or “_” button to select from 5min to 30min in a cycle (each 5 minutes is a level), and then click Settings” to confirm the setting.

ERROR CODE LIST

PARAMETER

display:$22.2mm/¢25.4mm / ¢31.Bmm
IP grade| IPSS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>