kbice FDFM1JA01Self Dispensing Nugget Ice Machine User Guide
- October 30, 2023
- kbice
Table of Contents
FDFM1JA01Self Dispensing Nugget Ice Machine
User Guide Self Dispensing 4Nugget Ice Machine
Quickstart Guide — Model: FDFM1JA01
INSTALLATION REQUIREMENTS
Clearance Requirements
CAUTION
- This unit is designed for countertop use only.
- Never block the air vent on the left side.
- This unit is designed to be in operation in an area with a maximum ambient temperature of 80°F, 26°C. Warmer ambient temperature will result in reduced ice quality and product.
- Never operate this unit in direct sunlight.
- Allow for a minimum clearance of 12 inches on the left side, ½ inch on the right, 2 inches on the back, and ½ on the top of clearance on the left side, to ensure proper function of the unit.
Scan here for instructional video:
[http://youtube.com/watch?v=Vr3lmwV2BZA&feature=youtu.be](https://youtube.com/watch?v=Vr3lmwV2BZA&feature=youtu.be)- Display Panel
- Ice Dispense Point
- Water Port for Funnel
- Reservoir Cover
- Air Vent
- Water Drip Tray
- Power Cord
- Drain Tube Plugs/Holder
Electrical Requirements
DANGER
It is required that you connect this unit only to a GFCI protected receptacle.
It is strongly recommended that you do not use an adapter to connect this unit
because of safety hazards.
Water Requirements
WATER
We recommend using distilled, bottled OR filtered water, as this will improve
the performance of the machine. Tap water with a hardness of <100 PPM is also
acceptable. The machine will NOT produce ice and will automatically go into
clean mode if tap water
with a hardness > 100 PPM is used
NOTE
Do NOT add water until Water Level red LED flashes. Do NOT overfill the
reservoir, otherwise it may overflow when ice melts completely.
USE OF DISPENSER
1. Filling the water reservoir for the first time use
• Remove the reservoir cover by simultaneously pulling from the left and right
side towards you
• Add water to MAX WATER FILL and then replace cover.
• Do not plug in until you have filled water to max fill line
• Plug unit into power
2. Flushing the
unit for the 1st time
• Plug the unit into power.
• Press and hold Clean button for 3 seconds to start the Cleaning mode
• Unplug the unit when the flushing process is complete (it takes 30 minutes
and the Cleaning LED goes off).
• Pull the drain tubes with plugs/holders out of the unit back and remove the
plugs/holders to release water.
• Replace the plugs/holders and put the tubes with plugs/holders back to the
unit.
3. Making ice for the 1st time. IMPORTANT
• We recommend using distilled, bottled OR filtered water, as this will
improve the performance of the machine. Tap water with a hardness of <100 PPM
is also acceptable. The machine will NOT produce ice if tap water with a
hardness > 100 PPM is used
• Unplug the machine
• Remove the reservoir door and fill the machine by sight to the max fill
line, located on the back of the water reservoir.
• Replace the cover and plug the unit into power.
• Press Make Nuggets button once and wait for the Making Ice LED to flash
slowly
FIRST TIME USE
Dispense several cups of ice and discard them.
4. Using the funnel
• Insert funnel into the water port
• Add distilled, bottled OR filtered water until the Water Level LED button
illuminates in green. You will hear 5 beeps.
• Re move the funnel to close port
Note: Funnel is Packed Inside the Reservoir
©KB Ice & H²0, LLC
Updated 2/8/21
www.kbgoodice.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>