KARCHER CV 30/2 Bp Upright Brush Type Vacuum Cleaners Instruction Manual

CV 30/2 Bp
CV 30/2 Bp Pack

CV 30/2 Bp Upright Brush Type Vacuum Cleaners

Description of the device

Illustration A

Preparation

1. Unpack the device and install the accessories.
   Illustration B

• only included with the scope of delivery for the CV 30/2 Bp Adv *INT

Startup

Inserting the battery pack

1. Slide the battery pack into the battery holder and lock it in place.
   Charging the battery pack

Note
Please read the operating instructions of the charger manufacturer, especially the chapters on safety instructions!
Note
Please read the operating instructions  of the battery pack manufacturer, especially the chapters on safety instructions!
Note
The battery pack is partially charged on delivery.
Charge before use and when necessary.
Note
The battery pack can only be charged when it is removed.

1. Press the unlocking button and remove the battery pack.
2. Charge the battery pack according to the operating instructions of the charger manufacturer and the battery pack manufacturer.

Installing HEPA filter (optional accessory)

1. Unlock and remove the filter cover.

2. Push out and remove the motor protection filter.
   Illustration C

3. Slide the HEPA filter (optional accessory) into the holder, swivel downwards and engage.
   Illustration D

4. Insert the filter cover and engage audibly.
   Illustration E

Installing the filter bag

1. Unlock and remove the filter cover.
2. Pull the opening of the filter bag over the suction connection as far as it will go. The locking mechanism of the filter  bag engages. Illustration F
3. Insert the filter cover and engage audibly.

Operation

Switch on the device

1. Switch on the device at the main switch.

Eco-Mode
Eco button (energy-saving mode): The device works with reduced suction performance. The battery run time is extended.

1. To activate Eco-mode: Actuate the Eco button.
2. To switch off Eco-mode: Actuate the Eco button repeatedly.

Adjusting the suction power
Note
Reduce the suction power at the control dial to reduce the pushing force on deep-pile carpets.

1. Adjust the suction power (min-max) via the rotary control.

Roller brush operation

ATTENTION
Device is operated too long on the same spot Risk of damage to the floor covering
Only operate the device briefly on the same spot.

1. Unlock brush head. While doing so, step on the tread and swing the handle backwards. The roller brush is switched on.
2. Perform cleaning.
3. Work interruption/end of cleaning: Lock the brush head. While doing so, step on the tread and swing the handle forward. The roller brush is switched off.

Semi-automatic brush cleaning
Note
The semi-automatic brush cleaning should be operated at least once a day, depending on the application, to remove light soiling.
For heavier soiling, see “Cleaning the roller brush manually”.

Note
The semi-automatic brush cleaning can only be switched on when the device is switched on.

1. Press the foot button of the semi-automatic brush cleaning. Step on the tread three times for five seconds.
   This results in  system-related noise development.

Suction pipe operation
Note
For cleaning, for example, edges, ledges, niches, corners.

1. Pull the suction pipe out of the mount. The brush motor is switched off.
2. Attach the desired accessory to the suction tube.
3. Perform cleaning.

Switching off the device

1. Switch off the device at the main switch.

Transport

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transportation.

1. Carry the device by the carrying handle.
2. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with  the respective valid  guidelines.

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be stored indoors.

1. Press the unlocking button and remove the battery pack to prevent discharge.

Care and service

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the battery pack.
Maintenance intervals
Daily

1. Perform semi-automatic brush cleaning.
2. Check roller brush for heavy soiling. If necessary, clean the roller brush manually.

Weekly
Note
Visual brush inspection: The degree of wear can be determined by comparing the differently coloured indicator tufts. Replace the roller brush when the black bristles are the same height as the red bristles.

1. Check the wear of the roller brush.

Changing the filter bag

1. Unlock and remove the filter cover.
2. Press the filter bag lock to the right and at the same time pull the filter bag downwards by the flange. Remove the filter bag,  close it and dispose of  it. Illustration G
3. Insert the new filter bag and pull the opening of the filter bag over the suction connection as far as it will go. The locking mechanism of the filter bag engages.
4. Insert the filter cover and engage audibly.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the battery pack.
Note
The device must be switched off immediately if a malfunction occurs (e.g. filter breakage).
The malfunction must be eliminated  before switching the device on again.

Remove the blockage
Suction pipe/suction hose
Illustration K
Illustration L
Note
When inserting the suction hose into the suction hose port, make sure that it engages in place.
Suction hose at brush head Illustration M
Roller brush/brush head Illustration N
Note
If necessary, remove the brush cover (see “Cleaning the roller brush manually”).

Error codes
E1
Suction volume too low, indicator light flashes

1. Replace the filter bag.
2. Remove blockages from the brush head, suction pipe and suction hose.

E2
Turbine error, indicator lamp flashes

1. Switch off the device and wait 1 minute. Switch the device back on.
2. If the fault occurs repeatedly, notify customer service.

E3
Power transmission to roller brush interrupted, indicator lamp flashes

1. Notify Customer Service.

E4
Temperature of the battery pack too high, indicator lamp flashes

1. Reset the error by actuating the main switch.
2. If the fault occurs repeatedly, replace the battery pack. Check the removed battery pack according to the manufacturer’s operating instructions.

E5
Current consumption of the brush motor too high, indicator light flashes

1. Switching off the device and check the roller brush for blocking objects and remove these if present.
2. If the malfunction occurs repeatedly, notify customer service.

E6
Current consumption of the turbine too high, indicator light lamp flashes

1. Notify Customer Service.

E7
Turbine defective, indicator light flashes

1. Notify Customer Service.

E8
Current consumption of the battery pack too high, indicator light flashes

1. Switch off the device. Reset the error by actuating the main switch.
2. If the fault occurs repeatedly, replace the battery pack. Check the removed battery pack according to the manufacturer’s operating instructions.

E9
Battery pack error, indicator light flashes

1. Remove the battery pack and reinsert it.
2. If the malfunction occurs repeatedly, replace the battery pack. Check the removed battery pack according to the manufacturer’s  operating instructions.
3. If the malfunction recurs, notify Customer Service.

E0
Interface error

1. Remove the battery pack and reinsert it.
2. If the malfunction occurs repeatedly, replace the battery pack. Check the removed battery pack according to the manufacturer’s operating  instructions.
3. If the malfunction recurs, notify Customer Service.

The device is not working

1. Switch on the device.
2. Charge the battery pack.
3. Insert the battery pack.

Unsatisfactory vacuuming result

1. Replace the filter bag.
2. Remove blockages from the brush head, suction pipe and suction hose.
3. Replace motor protection filter or HEPA filter (optional accessory).

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.

Spare parts list
Only use KÄRCHER original battery packs, not non-rechargeable batteries.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well  as in the version placed in circulation by us. This declaration is invalidated by any changes made to the  machine that are not approved by us.
Product: Dry vacuum cleaner
Type: 1.023-xxx
Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2011/65/EU
2014/30/EU
Harmonised standards used
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60312-1: 2017
EN 60335-1
EN 60335-2-69
EN 62233: 2008
National standards used
The signatories act on behalf of  and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01

Technical data

Electrical connection| |
---|---|---
Battery pack nominal voltage| V| 36 DC
Protection class| | Ill
Nominal power| W| 420
Device performance data| |
Tank content| I| 3
Volume of filter bag| I| 2,3
Air quantity (max.)| Ws| 34
Vacuum (max.)| kPa (mbar)| 18,7 (187)
Operating time at full battery charge – Battery Power 36/50 bat- tery pack| Minutes| 28/Eco: 38
Operating time at full battery charge – Battery Power+ 36/60 battery pack| Minutes| 32/Eco: 50
Operating time at full battery charge – Battery Power+ 36/75 battery pack| Minutes| 47/Eco: 67
Dimensions and weights| |
Length x width x height| mm| 250 x 310 x 1150
Width of roller brush| mm| 252
Typical operating weight| kg| 8
Ambient conditions| |
Ambient temperature (max.)| °C| +40
Determined values in acc. with| EN 60335-2-69|
Sound pressure level LpA| dB(A)| 64
Uncertainty KpA| dB(A)| 2
Sound power level LWA| dB(A)| 77
Hand-arm vibration value| m/s2| <2,5
Uncertainty K| m/s2| 0,5
Subject to technical modification:.| |

THANK YOU!
MERCI! DANKE! ¡GRACIAS!
Register your product and benefit from many advantages.
www.kaercher.com/welcome Rate your product and tell us your opinion.www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA | Kärcher
• Reinigungsgeräte und Hochdruckreiniger | Kärcher
• Lieferkette und Produkte | Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>