myCharge Voyage 1000 RFAM-0206 User Manual

: October 30, 2023
: myCharge

Table of Contents

myCharge Voyage 1000 RFAM-0206
In The Box
Section I: Quick Start
Section II: Charging Voyage
Section III: Charging Devices
Section IV: Checking Battery Level
Section V: Sound Mode
Section VI: Lanyard Strap
Section VII: Maintenance
Section VIII: Product Specifications
Section IX: Troubleshooting
RFA Brands Service Center
DOWNLOAD
Read User Manual Online (PDF format)
Download This Manual (PDF format)

myCharge Voyage 1000 RFAM-0206

OWNER’S MANUAL

Thank you for choosing myCharge Voyage™ 1000

In The Box

myCharge Voyage
Lanyard
Owner’s Manual
Warranty Manual

Controls

Section I: Quick Start

Charge up your Voyage by plugging it into a USB power adapter or computer. As Voyage charges, LEDs on the unit will sequentially illuminate. When the unit is fully charged, all LEDs are lit. Press the level check button to see how much power is available.
Connect your device to the Micro-USB connector.
Unplug your device when it’s charged and go! Your Voyage will automatically power off after your device is unplugged.

Section II: Charging Voyage

To charge your Voyage, connect it to a USB power source (USB-A to wall adapter, notebook USB port) with the on-board green USB input cable. Times to charge the Voyage vary based on what it’s plugged into. You can expect a full charge from a USB adapter in about an hour and a half, or from a standard notebook USB port in about two and a half hours.

Note: It is normal for your Voyage to be warm to the touch while in use.

Section III: Charging Devices

Voyage uses an automatic device detection system. When a device is plugged in the Voyage provides charging power until it is unplugged or the Voyage runs out of energy. The Voyage Micro-USB connector is compatible with the majority of mobile devices including smartphones, Bluetooth headsets, portable navigation devices, MP3 players, and more.

Section IV: Checking Battery Level

To check how much energy is available, press the level check button. LEDs next to the button will illuminate indicating approximately how much energy is available for use.

LED 1 Flashing: Under 20%
LED 1: 21-40%
LED 2: 41-65%
LED 3: 66-90%
LED 4: 91-100%

Section V: Sound Mode

Voyage has built-in tone capability. Tone mode will audibly inform you when devices are plugged in or disconnected, and when the unit is charging or has completed charging.

To disable, enable and/or change the sound mode

Locate the Sound pinhole button under the green USB-A cable
Plug Voyage into your PC
Use a paperclip to cycle Tone Silent

If you prefer no sound toggle to the silent mode – unit will make no sound when this option is selected. If you prefer tone mode toggle until you hear the tone.

Section VI: Lanyard Strap

Your Voyage includes a lanyard strap for easy portability. To affix it to Voyage, slide the skinny loop of the strap under the rod in the opening, then pull the thick strap through the loop.

Section VII: Maintenance

To keep Voyage operating at its full potential, please do the following:

Re-charge every three months when not in use.
Keep dry and away from moist and corrosive materials.
To clean, wipe surface with dry cloth.

Section VIII: Product Specifications

Battery: 1000 mAh Lithium Polymer
Input:
USB-A: 5 VDC, 1.0 A
Output:
Micro-USB: 5 V, 1.0 A
Total Output Current: 5 V, 1.0 A

Section IX: Troubleshooting

My device is not charging: Confirm that your device is properly connected to the Micro-USB connector and the Voyage itself has energy (by pressing the level check button). LEDs indicate how much energy is available for use. If the Voyage has energy and your device is not charging, unplug it and plug it back in. If this still doesn’t work, use your device cable to make sure the device is working properly.

I don’t want the tone function on: Refer to Section V: Sound Modes.

For additional troubleshooting information and device compatibility, please visit: www.mychargepower.com