KARCHER 11986220 VC 4 Cordless myHome Instruction Manual
- October 30, 2023
- Karcher
Table of Contents
- Safety instructions for battery powered vacuum
- Safety instructions for transportation
- Intended use
- Environmental protection
- Accessories and spare parts
- Warranty
- Scope of delivery
- Device description
- Installing the wall bracket
- Initial startup
- Installing accessories
- Operation
- Ending operation
- How to use the Accessories
- Transportation
- Storage
- Care and service
- Troubleshooting guide
- Removing and installing the battery
- Technical data
- THANK YOU!
**KARCHER 11986220 VC 4 Cordless myHome Instruction Manual
**
Safety instructions for battery powered vacuum
**** Read these safety instructions and the original instructions before using the device for the first time. Act in accordance with them. Keep the book for future reference or for future owners.
- In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.
- Warnings and information notices attached to the device provide important information for hazard-free operation.
- Depending on the device type, the battery/battery pack is either permanently installed or replaceable. Permanently installed batteries/battery packs must not be replaced. Please refer to the operating instructions of the device to find out what applies to your device.
A battery consists of a single storage element, whereas a battery pack consists of interconnected storage elements.
In the following chapters, both terms are used synonymously
Hazard levels
DANGER
- Indication of an imminent threat of danger that will lead to severe injuries or even death.
WARNING
- Indication of a potentially dangerous situation that may lead to severe injuries or even death.
CAUTION
- Indication of a potentially dangerous situation that may lead to minor injuries.
ATTENTION
- Indication of a potentially dangerous situation that may lead to damage to property.
General safety instructions
DANGER
- Risk of asphyxiation. Keep packaging film out of the reach of children.
- Operation in explosive atmospheres is prohibited.
- Risk of explosion
- Never use the device to vacuum up combustible gases, liquids or dusts.
- Never use the device to vacuum up reactive metal dusts (e.g. aluminium, magnesium, zinc).
- Never use the device to vacuum up undiluted brine or acids.
- Never use the device to vacuum up any burning or smouldering objects/matter.
These substances can corrode the materials in use on the device.
WARNING
- Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device.
- Persons with reduced physical, sensory or mental capabilities and persons lacking experience and knowledge may only use the appliance if they are properly supervised, have been instructed on use of the appliance safely by a person responsible for their safety, and understand the resultant hazards involved.
- Only people who have been instructed on how to use the device, or have proven their ability to operate it, and have been explicitly instructed to use it, must use the device.
- Children must not operate the device.
- Children from the minimum age of 8 may use the appliance if they are properly supervised or have been instructed in its use by a person responsible for their safety, and if they have understood the resultant hazards involved.
- Children must be supervised to prevent them from playing with the appliance.
- Children may only perform cleaning work and user maintenance under supervision.
- Adhere to the respective safety regulations in hazard zones (e.g. service stations). Never operate the device in explosive spaces.
- Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device.
- The appliance contains electrical components – do not clean the appliance under running water.
- Risk of injury. Do not use the nozzle and suction pipe at head height.
- Avoid switching the device on unintentionally. Make sure that the on/off switch is in the off position before connecting the battery pack, lifting or carrying the device.
- You must not charge or store the device outdoors or in a car.
CAUTION
- Safety devices are provided for your own protection. Never modify or bypass safety devices.
- Do not use the appliance if it has been dropped beforehand, is visibly damaged or if it is leaking.
- Never leave the device unsupervised while it is in operation.
- Only operate or store the device in accordance with the description or figure.
- In order to prevent accidents or injuries, you must observe the weight of the device when transporting it.
- Accidents or damage due to the device falling over. Before all actions with or on the device, you must make sure that it is stable.
- Do not make any changes to the device, and only use accessories and spare parts recommended by the manufacturer.
- Risk of injury when loose fitting clothing, hair or jewellery is caught by moving parts of the device. Keep clothing and jewellery away from moving parts of the device. Tie long hair back.
ATTENTION
- Do not operate the device at temperatures below 0 °C.
- Never use the device without a filter, this can lead to device damage.
- Only use the device indoors
Charger safety instructions
DANGER
- Never touch the mains plug and socket with wet hands.
- Danger of explosion. Do not charge any non-rechargeable battery.
- Do not charge the battery pack in an explosion-hazard environment.
- Never insert conductive objects, e.g. screwdrivers or similar, into the charging socket on the appliance.
WARNING
- Only charge the appliance using the original charger enclosed or with a charger approved by KÄRCHER.
- Protect the power cable from heat, sharp edges, oil and moving parts.
- Do not open the charger. Repairs are only to be carried out by qualified personnel.
- Only use the charger for charging approved battery packs.
- Immediately replace a damaged charger together with charging cable with an original part.
- The appliance contains electrical components – do not clean the appliance under running water.
- You may not charge the battery pack for longer than 24 hours without interruption.
CAUTION
- Do not use the battery pack when dirty or wet.
- Keep the charger ventilation slits free of obstructions.
- Do not pull the mains plug out the socket using the power supply cable.
- Do not carry/transport the device using the power supply cable.
ATTENTION
-
Short circuit hazard. Protect the contacts of the battery pack from metal parts.
-
Only use and store the charger in dry rooms.
Note -
Information on which type of charger/adapter is to be used can be found on the type plate of the charger supplied and/or in the technical data in the operating instructions for the device.
Symbols on the charger
(Depending on the charger)
: Protect the device from moisture. Store the device in a dry place. Do not
subject the device to rain. The device is only suitable for indoor use. : The
device has a built-in fuse. The value (X) in amperes can be found on the
respective charger.
: The device meets the requirements of protection class II.
Battery/battery pack safety instructions
DANGER
-
Do not charge the battery pack in explosive atmospheres.
-
Do not throw battery packs into a fire or into the household rubbish.
-
Avoid contact with fluid leaking from defective batteries. Immediately rinse off the fluid using water if contact is made, and also consult a doctor in the event of
contact with the eyes. -
Danger of explosion. Do not charge any non-rechargeable battery.
WARNING
- Check that the voltage of the battery pack corresponds with the information on the type plate of the device used.
- Check the battery pack for damages before every operation. Do not use any damaged battery packs.
- Do not charge any damaged battery packs
- Replace damaged battery packs with battery packs approved by KÄRCHER. Does not apply to appliances with a fixed battery
- Do not open the battery pack. Repairs are only to be carried out by qualified personnel.
- Only charge the battery pack with the approved chargers.
- Do not charge the battery unattended. Check the condition of the battery and charger regularly during the charging process.
- Disconnect the charger from the mains and the battery from the charger and stop using the charger and battery if you notice a fault, unusual odours or heat development during charging. Contact the authorized customer service.
- Do not remove permanently installed batteries.
CAUTION
- Short circuit hazard. Protect the contacts of the battery pack against metal parts.
- Do not use the battery pack n a dirty or wet condition. Allow the connections to dry out completely before using the battery pack.
- Remove the battery pack from the device before carrying out any service or care work. Does not apply to appliances with a fixed battery
ATTENTION
- Short circuit hazard. Do not store the battery packs together with metal objects.
- Do not submerge the battery in water.
- Protect the battery pack against heat, sharp edges, oil and moving unit parts.
- Do not subject the battery pack to mechanical stress.
- Store the battery pack in a dry place.
Symbols on the battery pack
(Depending on device/battery type)
: Do not throw the battery into water.
: Do not throw the battery into fire.
: Do not charge defective battery packs.
: Only use the battery pack with the approved chargers. Information on which type of charger/adapter is to be used can be found on the type plate of the charger supplied and/ or in the technical data in the operating instructions for the device.
Safety instructions for transportation
The lithium-ion battery is subject to the requirements of dangerous goods
regulations.
The battery pack can be transported by the user in public traffic areas
without any further restrictions. When shipping by third parties (transport
companies), special requirements for packaging and labelling must be observed.
Do not use the battery pack if the casing is damaged.
Tape off open contacts. Pack the battery tightly and securely.
The battery pack must not be able to move in the packaging.
DANGER
- A defective or non-functional battery pack must not be mailed and must be disposed of on site in accordance with the applicable regulations. Observe the national regulations
Intended use
- Only use the device in private households.
- The device is intended exclusively for cleaning dry surfaces
- The following are not in accordance with the intended use:
- Cleaning people, animals, plants or clothing on the body.
- Soaking up water or other fluids.
- Extraction of glowing ashes, coal, cigarettes or other flammable or easily inflammable substances.
- Use in the vicinity of explosive or highly flammable substances.
Environmental protection
The packing materials can be recycled. Please dispose of packaging in
accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials
and often components such as batteries, rechargeable batteries or oil, which –
if handled or disposed of incorrectly – can pose a potential threat to human
health and the environment. However, these components are required for the
correct operation of the appliance. Appliances marked by this symbol are not
allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found at:
www.kaercher.com/REACH
Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the
appliance will run fault-free and safely.
Information on accessories and spare parts can be found at
www.kaercher.com
Warranty
The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)
Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.
Device description
The scope of delivery of the device (depending on the model) is shown on the packaging. These operating instructions describe all possible options For the illustrations, refer to the graphics page.
Illustration A
-
Battery/error message LED indicator light
-
Unlocking buttons for removing the exhaust air foam filter
-
Exhaust air foam filter cover
-
Boost function button (increase suction performance)
-
On/Off switch with locking lever
-
Handle
-
Replaceable battery
-
Battery unlocking button
-
Unlocking button for removing the dust container removal
-
Air inlet filter
-
Dust container flap
-
Removable dust container
-
Dust container cover flap unlocking button
-
Dust container suction fitting
-
Motorized electric brush with universal brush roller
-
Suction pipe
-
Crevice nozzle
-
Wall bracket
-
Charger
-
2-in-1 upholstery nozzle
-
Flexible extension hose
-
Flexible crevice nozzle
-
Large upholstery nozzle
-
2-in-1 furniture brush
-
Mini turbo brush
-
Soft brush
-
LED-crevice nozzle
-
Air inlet filter (2x)
-
Filter cleaning tool
-
Soft motor-driven brush (Hard floor nozzle)
option
Installing the wall bracket
The scope of delivery includes a wall bracket as well as screws and dowels for
tidy storage of the vacuum cleaner.
Note Mount the wall bracket at a suitable point using the screws and
dowels supplied. For safe storage of the device, position the lower edge of
the wall bracket 1.04 m from the floor.
Illustration E
ATTENTION
Material damage due to incorrect installation Incorrect installation can
damage both the device and the floor covering if it falls.
Use suitable mounting tools for wall mounting. Take the weight of the device
and the loading capacity of the installation location into account when
selecting the fasteners.
WARNING
Risk of electric shock and injuries Make sure there are no electrical cables,
water or gas pipes in the wall around the mounting area
Initial startup
Installing accessories
Note
The multi-function brush is also driven by its own integrated motor and
must therefore always be connected directly to the hand-held device or the
suction pipe in order to ensure the power supply.
All other accessor parts can also be used directly with the hand-held device or with the suction pipe to increase the reach.
-
Push the suction pipe on to the suction fitting of the dust container until it audibly clicks into place.
-
Press the unlocking button and remove the suction pipe from the suction fitting.
Illustration B
-
Push the floor nozzle on to the suction pipe until it audibly clicks into place.
-
Press the unlocking button and remove the floor nozzle from the suction pipe.
Illustration C
-
Push the accessory, such as the crevice nozzle, on to the suction fitting of the dust container or suction pipe until it audibly clicks into place.
**Illustration D
**
Battery charging
Note
The device is not supplied with a charged battery. Fully charge the battery
before using it for the first time. Please observe the enclosed safety
instructions for battery powered vacuum cleaners.
-
To charge the device, attach it to the wall bracket included in the scope of delivery.
Illustration E
-
Plug the charger into a socket. Insert the connecting plug into the charging socket of the device. The LED indicator light flashes green during the charging process.
Illustration F
-
When the device is fully charged, the LED indicator light lights up continuously green for 2 min. and then goes out. Remove the charger from the power socket and charging socket. Remove the device from the wall bracket.
Illustration G
The device is ready for use.
Operation
LED display
The LED on the head of the device shows information on the charging state of
the battery and error messages.
Battery charging state
LED | Duration of lighting | Meaning |
---|---|---|
Lights up green | continuously | Battery charged |
Flashes green | 1 s on / 1 s off | 2 min remaining running time (-1 min/+2 min) |
Flashes green | 125 ms on / 125ms off | Battery fault |
The progress of charging the battery can be read from the green LED. The LED
only lights up when the battery is correctly installed
While charging
LED | Duration of lighting | Meaning |
---|---|---|
Flashes green | 0.2 s from off to on /0.6 son/ 0.2 s from on to off /1s off |
Battery is charging
Lights up green| 2 min continu- ous lighting, then off| Battery fully charged
Error message
LED | Duration of lighting | Meaning |
---|---|---|
Flashesred | 125 ms on / 125ms off | Floor nozzle blocked |
Changing accessories
To change accessories, see chapter Installing accessories
Vacuuming
-
Install the required accessories, see chapter Installing accessories.
-
Switch on the device, depending on cleaning requirements:
-
Press the On/Off switch and keep it pressed during operation.
or -
Turn the locking lever to switch the device directly to continuous operation.
Illustration H
-
-
If necessary, press the Boost button to increase the dust intake.
Illustration I
Note
When the device is switched off, the boost function is automatically disabled.
The boost function can also be switched off by pressing the Boost button
again.
Ending operation
-
Switch off the device.
Release the On/Off switch or disable the locking lever.
Note
To ensure an optimum suction performance, empty the dust container and clean the air inlet filter after each use. Empty the dust container at the latest when the “MAX” marking is reached. -
Remove the suction pipe or accessory.
-
Empty the dust container into a waste container.
a Press the unlocking button. The dust container flap opens.
b Empty the dust container.
Illustration J
-
To close the flap, push the dust container upwards until it clicks into place.
-
Clean the air inlet filter, see chapter Cleaning the air inlet filter
-
Attach the device to the wall bracket.
Illustration E
-
Charge the device, see chapter Battery charging.
How to use the Accessories
General instructions for use
-
Which accessories are included in the scope of delivery is shown on the device packaging.
-
Accessories not included in the packaging can be purchased in a KÄRCHER specialist shop or from www.kaercher.com.
-
Test the accessory at an inconspicuous point before using it in a sensitive area.
-
Follow the manufacturer’s cleaning instructions.
-
Connect the motor-driven electric nozzle to the suction pipe or the hand-held device.
-
Also connect the other accessory parts, such as crevice nozzle, to the hand-held device or push it directly onto the suction pipe to increase the reach.
Motor-driven multi-function brush
Ideal for hard floors and carpets. The motor-driven multi-function brush removes dirt stuck between the carpet fibres particularly effectively.
2-in-1 upholstery nozzle
The frame with the surrounding bristles can be taken off pressing the unlocking button. -
The soft brush is suitable for furniture with hard surfaces
-
The wide brush is used to clean upholstered furniture, curtains, etc.
Crevice nozzle
For edges, joints, heaters and areas that are difficult to reach.
Soft brush
The soft brush has particularly soft bristles for cleaning sensitive surfaces
such as keyboards, lamps, etc.
Flexible crevice nozzle
The flexible crevice nozzle increases the reach. For cleaning hard-to-reach
places, such as between the car seats.
Flexible extension hose
Due to the extension and flexibility, hard-to-reach areas such as in the car
can be reached and cleaned.
Large upholstery nozzle
For cleaning textile surfaces such as sofas, armchairs, mattresses, car seats,
etc.
2-in-1 furniture brush
For gentle cleaning of sofas and delicate furniture. Depending on
requirements, the accessory can be used as a furniture or upholstery nozzle by
pressing the button.
Mini turbo brush
Efficiently removes pet hair and dust particles from upholstered furniture,
mattresses or other soft surfaces. The rotating round brush catches even the
finest hair.
LED-crevice nozzle
For cleaning corners and hard-to-reach areas. The illumination makes even the
finest dust visible in dark spaces.
Soft motor-driven brush (Hard floor nozzle)
For hard floors and sensitive wooden floors. Extracts coarse and fine dirt
simultaneously.
Transportation
The battery has been tested in accordance with the relevant rules for international transport, and can be transported / shipped.
Storage
ATTENTION
Moisture and heat
Risk of damage Store batteries only indoors in a dry place with low humidity
and temperatures below 20°C.
Care and service
General care instructions
- Clean the device and plastic accessory parts with a commonly available plastic cleaner.
Cleaning the air inlet filter
Note
The device can be cleaned manually or using a filter cleaning device.
-
Switch off the device.
-
Manually cleaning the air inlet filter.
a Pull the soiled air inlet filter down at the filter stick, carefully beat it and clean it with a damp cloth or running water.
Illustration K
b Reinsert the fully dried air inlet filter.
c Check for correct seating. -
Cleaning the air inlet filter with a filter cleaning device.
Note
A new air inlet filter must be installed in the dust container during filter
cleaning.
a Push the filter cleaning device on to the suction pipe branch and pull
the air inlet filter out of the device using the filter stick.
b Push the soiled air inlet filter into the filter cleaning device.
c Insert a new air inlet filter into the dust container.
Illustration L
d Switch on the device and let it run in boost mode while turning the
side cover.
Illustration M
e Remove the cleaned air inlet filter from the filter cleaning tool and
reinsert it in the dust container after removing the new air inlet filter.
f Check that the air inlet filter is correctly seated.
Cleaning the dust container and cyclone filter
Note
The dust container and cyclone filter can be cleaned with or without removing
the dust container. We recommend removing the dust container from the device
for easy cleaning.
Note
Before cleaning the dust container and cyclone filter, empty the dust
container, see chapter Ending operation
- . Switch off the device.
- Press the unlocking button for the dust container and remove the dust container from the hand-held device.
Illustration N
a Remove the cyclone filter from the dust container by turning it anticlockwise.
b Remove the cyclone filter from the dust container and take the air inlet filter out of the cyclone filter.
Illustration O
ATTENTION
Short circuit hazard
There are cables or contacts in the dust container and cyclone filter for the
power supply. Make sure that the cables or contacts do not get wet when
cleaning.
-
lean the dust container and cyclone filter with a soft brush or a slightly damp cloth.
Illustration P -
Clean the air inlet filter, see chapter Cleaning the air inlet filter
-
Re-insert the dry dust container and cyclone filter with air inlet filter into the device and close the flap.
-
Attach the dust container to the handheld device.
a Hold the dust container at an angle against the handheld device while holding the top on the hook of the handheld device.
b Push the dust container upwards until the hook on the handheld device engages in the slot in the dust container.
c The dust container must audibly click into place.
**Illustration Q
**
ATTENTION
Health risk
Exhaust air foam filters that are not completely dry when installed in the
device can be a breeding ground for spores and mould. Make sure that the
exhaust air foam filter is completely dry on installation.
c Then allow the exhaust air foam filter to dry completely.
d Fasten the cover to the exhaust air foam filter.
Illustration S
e Insert the exhaust air foam filter into the device until it latches
into place.
f Press the cover down in the middle to ensure that the cover sits
correctly on the device.
Illustration U
- Replace the exhaust air foam filter.
a Press both side unlocking buttons at the same time and remove the exhaust air foam filter.
Illustration R
b Remove the cover of the exhaust air foam filter and dispose of the used filter.
c Fasten the new exhaust air foam filter to the cover.
Illustration T
d Insert the exhaust air foam filter into the device until it latches into place.
e Press the cover down in the middle to ensure that the cover sits correctly on the device.
**Illustration U
**
Cleaning the multi-function nozzle
-
Switch off the device.
-
Remove accessories.
ATTENTION
Short circuit hazard
The multi-function brush contains electrical components. You must not immerse the multi-function brush in water or clean it with a damp cloth. -
Clean the multi-function brush.
a Unlock the brush roll cover / support with a coin or other object and remove it.
Illustration V
b Remove the brush roll from the brush opening in the direction of the arrow.
Illustration W
c Remove the dirt e.g. with a brush. If necessary, tangled threads or hair can be carefully cut off with scissors.
d Carefully clean the brush opening with a cloth or soft brush.
Illustration X
e Insert the brush roll into the brush opening.
f Lock the brush roll with a coin or other object.
**Illustration Y
**
- lu
Cleaning the mini turbo brush
-
Switch off the device.
-
Remove accessories..
ATTENTION
Short circuit hazard
The mini turbo nozzle contains electrical components. Do not immerse the mini turbo nozzle in water or clean with a damp cloth. -
Cleaning the mini turbo brush:
a Press down on the brush roll cover and remove the brush roll.
Illustration Z
b Remove the dirt e.g. with a brush. If necessary, tangled threads or
hair can be carefully cut off with scissors.
c Clean the brush opening carefully with a cloth or soft brush.
Illustration AA
d Insert the brush roll at an angle and fully into the brush opening,
pushing up until the cover snaps into place.
**Illustration AB
**
Troubleshooting guide
- Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.
The device does not start up
Battery is empty.
- Charge the rechargeable battery.
Battery is not inserted correctly.
- Push the battery into the mount until it locks into place.
Battery is defective.
-
Replace the battery.
The battery is not charging The charging plug/mains plug is not connected correctly. -
Connect the charging plug/mains plug correctly.
The socket is defective.
- Check that the socket is working.
- Check that the correct charger is being used.
The device stops during operation or the suction
performance is poor
The battery has overheated.
- Stop work and wait until the battery temperature is back in the normal range.
The accessories, the suction opening on the dust container or the suction pipes are clogged.
- Remove the clog with a suitable aid.
The dust container is full.
- Empty the dust container.
The filters are soiled.
- Clean the filters, see chapter Care and service.
Roller brush is blocked.
- Remove any blockage.
Abnormal engine noise
The accessories, the suction opening on the dust container or the suction
pipes are clogged.
- Remove the clog with a suitable aid.
Removing and installing the battery
ATTENTION
Frequent removal of the battery
Frequent removal of the battery can damage the battery.
Only remove the battery for maintenance and care if the device is not used for
a long period of time or if the device has to be sent for servicing.
Removing the battery
- Press the unlocking button.
- Remove the battery from the device.
**Illustration AC
**
Inserting the battery
ATTENTION
Dirty contacts
Damage to the device and battery Check the battery mount and the contacts for
soiling and clean them as necessary before inserting the battery.
Note
Use only fully charged batteries.
- Push the battery into the mounting in the device until it audibly latches into place.
**Illustration AD
**
Technical data
Electrical connection
Voltage of charger| V| 21,6
Nominal power| W| 140
Battery pack type| Li-ION
Charger| 26 V TEK *EU
Model| YLJXA-E260040
Part number| 9.769-119.0
Nominal voltage of charger| V| 100 –
Frequency| Hz| 50 – 60
Charging time when the battery is completely discharged| min| 345
Protection class| | II
Device performance data
Tank content| l| 0,65
Operating time when battery is fully charged in normal operation| min| 30
Operating time in maximum mode when battery fully charged| min| 18
Dimensions and weights
Weight (without accessories)| kg| 1,55
Subject to technical modifications.
THANK YOU!
Register your product and benefit from many advantages.
Rate your product and tell us your opinion.
MERCI!DANKEKE!IGRACIAS!
www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40 71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212
References
- Cleaning equipment and pressure washers | Kärcher International
- Dealer Search | Kärcher International
- Supply chain and products | Kärcher International
- Home and Garden Warranty Registration USA | Kärcher