ISHIDA UNI8P Electronic Scale User Manual
- October 30, 2023
- ISHIDA
Table of Contents
UNI8P Electronic Scale
User’s Manual
UNI8P Electronic Scale
IMPORTANT
- Read this manual and the user manual enclosed with the model thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents.
- Keep this manual and the user manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.
PRECAUTION SYMBOLS
This machine is manufactured for use according to proper procedures by a
qualified person and only for the purposes described in this manual. The
following conventions are used to indicate and classify precautions depending
on the level of danger, or seriousness of potential injury. Always heed the
information provided in this manual. Failure to heed precautions can result in
personal injury or property damage.
The following precaution symbols are used in this manual.
WARNING
Indicates a potentially hazardous situation which, if not avoided, may result
in serious injury or death. Additionally, there may be significant property
damage.
CAUTION
Indicates a potentially hazardous situation where, if not avoided, may result
in minor or moderate injury or in property damage.
NOTICES
IMPORTANT NOTICE
Those who handle the machine must be aware of the hazards involved. These
dangers may not be obvious, so it is imperative to follow the instructions
detailed in this manual and the manual enclosed in CD when installing,
operating, inspecting, or servicing the machine. Therefore, we recommend that
you thoroughly read and understand these manuals before installing, operating,
inspecting, or servicing the machine. ISHIDA is not liable for any damage,
loss or injury that results from incorrect operation, insufficient caution,
unauthorized modifications to the machine, or failure to follow the
instructions contained in these manuals.
LIMITATIONS OF LIABILITY
ISHIDA assumes no responsibility for special, indirect, or consequential
damages, loss of profits or commercial loss in any way connected with the
machine, whether such claim is based on contract, warranty, negligence, or
strict liability.
ISHIDA assumes no responsibility for the user’s programming of this machine,
or any consequence thereof.
In no event shall ISHIDA be responsible for warranty, repair, or other claims
regarding the machine unless ISHIDA’s analysis confirms that the machines were
properly handled, stored, installed, and maintained and not subject to
contamination, abuse, misuse, or inappropriate modification or repair.
CHANGE IN SPECIFICATIONS
Machine specifications and accessories may be changed at any time due to
improvements or other reasons. Consult with your ISHIDA representative at any
time to confirm the actual specifications of the purchased
machine.
ERRORS AND OMISSIONS
The information in this manual has been carefully checked and is believed to
be accurate; however, no responsibility is assumed for clerical, typographical
or proofreading errors, or omissions.
PRECAUTIONS FOR SAFE USE
It is strongly advised that the following safety measures must be observed to
ensure the safe operation of the machine.
IMPORTANT
- Read this manual and the manual enclosed in CD or WEB thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents.
- Keep this manual and the manual enclosed in CD or WEB in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.
WARNING
- This product is a commercial scale which is not intended for use by children.
- It is not suitable for use in locations where children are likely to be present.
- Prepare a dedicated power source and always use a power supply with rated voltage. Never connect the machine power input with an AC power supply exceeding the rated voltage. To avoid any potential electrical shock, ensure that the protective ground wire is connected to the main grounding provision.
- A power supply that generates voltage variation may cause a malfunction, or using the machine outside of the rated voltage may result in machine failure or danger such as electric shock.
- The equipment disconnect device is considered to be: Plug, the socket-outlet shall be easily accessible.
- For telecommunication type connectors and terminals not used for connection to the telecommunication network. It should be intended to be used for Cash Drawer.
- Replacement of fuses is limited only by service personnel. Service personnel should refer to service documentation for instructions for the replacement.
- Replacement of Battery is limited only by service personnel.
- This product contains a battery. During using, storing, or transporting this product, do not place it in extremely hot or cold places, or at high altitude and low atmospheric pressure.
- Don’t disposal of battery into fire or a hot oven.
- Don’t leave the product including a battery in an extremely high temperature surrounding environment or the leakage of flammable liquid or gas.
* To Service personnel:
Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
PRECAUTION REGARDING FCC RULE IN USA
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
PRECAUTION REGARDING WIRELESS MODULE
It is strongly advised that the following safety measures must be observed to
ensure the safe operation of the machine in case that wireless module is
installed.
For Canada / USA
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC/IC radiation exposure limits set forth for a
controlled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm
or more away from person’s body (excluding extremities: hands, wrists, feet
and ankles). Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser) gain approved
for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
For below detachable antenna statement, only for hanging type electronic scale
and only for IC:30176-UNI8H. This radio transmitter 30176-UNI8H has been
approved by Innovation, Science and Economic Development Canada to operate
with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater
than the maximum gain indicated for any type listed are strictly prohibited
for use with this device.
The concrete contents to check are the following three points.
- Must use antenna such as Dipole with gain not exceeding 4.41dBi;
- Should be installed so that the end user cannot modify the antenna;
- Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network.
© ISHIDA Co., Ltd. 2022 All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means mechanical, electronic,
photocopying, recording, or otherwise without prior written permission of
ISHIDA.
ISHIDA CO., LTD.
44 SANNO-CHO, SHOGOIN, SAKYO-KU
KYOTO, 606-8392 JAPAN
PHONE: 81-75-771-4141
FACSIMILE: 81-75-751-1634
URL:http://www.ishidajapan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>