UNI-8 Price Computing Scale

Product Information: UNI-8 Quick Operation Manual

The UNI-8 is a weighing scale available in bench, pole, and
hanging types. It comes with a user manual that provides important
information on installation, operation, maintenance, and
inspection. The manual also includes instructions for turning on
the power, setup mode, calibration, program mode, and PLU data.

Chapter 1: Turning On the Power

To turn on the UNI-8:

1. Push down the Power Switch.

2. The Clock Check screen will appear. Check that the displayed
   date and time are correct and press the [ENTER] button to
   proceed.

3. The initial screen will appear.

Chapter 2: Setup Mode

To access the Setup Mode:

1. Turn on the power.

2. Press the button at the upper right side of the screen.

3. Press the [SETUP] and [LOGIN] buttons, input Password 495344
   using numerical keys, and press [SET] button.

4. To log out, press only the [LOGIN] button.

Chapter 3: Calibration

The Calibration menu includes:

• CAPACITY: Select the capacity of the scale (6000g / 6kg / 15kg
  / 30kg / 30lb).

• RANGE: Select the range (SINGLE / MULTI).

• GRAVITATIONAL ACC.: Enter the gravitational acceleration (input
  range: 97799 to 98300).

• DATA DISPLAY: Select the A/D or cell voltage display (WEIGHT /
  VOLTAGE).

• INITIAL ZERO: Initialize the scale.

• SPAN: Add or deduct span value.

Product Usage Instructions

Follow the below instructions to use the UNI-8:

1. Read the user manual thoroughly before installation, operation,
   maintenance, or inspection.

2. Keep the manual in a safe place where it is easily
   accessible.

3. To turn on the power, push down the Power Switch, check the
   displayed date and time, and press the [ENTER] button.

4. Access the Setup Mode by pressing the button at the upper right
   side of the screen and following the instructions on the
   manual.

5. To calibrate the scale, select the Calibration menu and follow
   the instructions to adjust the CAPACITY, RANGE, GRAVITATIONAL ACC.,
   DATA DISPLAY, INITIAL ZERO, and SPAN settings.

6. Refer to the manual for instructions on Program Mode and PLU
   Data.

UNI-8
Quick Operation manual

Bench type

Pole type

IMPORTANT
Read this manual thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.

Hanging type
Ver. 0.00

© ISHIDA Co., Ltd. 2022 All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means mechanical, electronic, photocopying, recording, or ohterwise without prior written permission of ISHIDA.
II

TABLE OF CONTENTS
CHAPTER 1 TURNING ON THE P OWER……………………………………………………….1-1 1.1 TURNING ON THE POWER ……………………………………………………………………… 1-1
CHAPTER 2 SETUP MODE…………………………………………………………………………..2-1 2.1 STARTUP ………………………………………………………………………………………………. 2-1
CHAPTER 3 CALIBRATION…………………………………………………………………………..3-1 3.1 CALIBRATION …………………………………………………………………………………………… 3-1
3.1.1 Procedure for adjusting scale (span) ………………………………………………………………. 3-2
CHAPTER 4 PROGRAM MODE ……………………………………………………………………4-1 4.1 PROGRAM MODE ENTRY / EXIT ……………………………………………………………… 4-1
CHAPTER 5 PLU DATA ………………………………………………………………………………..5-1 5.1 PLU DATA………………………………………………………………………………………………. 5-1
&+$37(563(&,),&$7,21 63(&,),&$7,21
III

IV

CHAPTER 1 TURNING ON THE POWER
1
TURNING ON THE POWER
1.1 TURNING ON THE POWER
1. Push down the Power Switch to turn on the power.

2. The “Clock Check” screen is displayed. Check that displayed date and time agree with the current date and time, and press the [ENTER] button on the screen to proceed to the next step.
Note: Refer to the “Date/Time” menu in Adjustment Mode when changing date or time.

Power switch

3. The initial screen is displayed.

Note: The contents of the initial screen may

KPLY

KLWLUKPUNVU[OLZL[[PUNZVU`VY

machine.

1-1

SETUP MODE
2.1 STARTUP
1. Turn on power.

CHAPTER 2 SETUP MODE
2

2. Press button at the upper right side of ccreen.

Power SW

Press [SETUP] and [LOGIN] button, then input Password “495344” using numerical keys, and press [SET] button.
495344
3. Press only [LOGIN] button to log out.
2-1

CHAPTER 2 SETUP MODE
Before log in Login screens Common operating buttons

9L[YU [V 4LU 9L[YU [V WYL]PVZ WHNL .V [V UL_[ WHNL 0UW[ BD

2-2

CALIBRATION
3-1 CALIBRATION

CHAPTER 3 CALIBRATION
3

Menu name CAPACITY
RANGE
GRAVITATIONAL ACC. DATA DISPLAY
INITIAL ZERO SPAN + –

Specification Select the capacity of the scale. 6000g / 6kg / 15kg / 30kg / 30lb Select the range. SINGLE / MULTI The range to be selected is limited depending on the capacity. Enter the gravitational acceleration. Input range: 97799 to 98300 Select the A/D or cell voltage display. WEIGHT / VOLTAGE Initialize the scale. Enter the current scale status to zero. Enter the current scale status to CAPACITY according to CAPACITY setting. Add span value. Deduct span value.

3-1

CHAPTER 3 CALIBRATION
3.1.1 Procedure for adjusting scale (span)
1. Press the “ZERO” key to adjust the zero point. ;OLU[OL >,0./; KPZWSHZÄLSKZOV^Z RN VY SI *OLR[OH[[OL (+ KPZWSHÄLSKZOV^Z HUK[OL :7(5(+ ÄLSKZOV^Z
75000
“0.000kg” or “0.00lb”
7SHJL[OL^LPNO[ZVM[OLZHTL^LPNO[HZ[OLWWLYSPTP[VM[OL^LPNOPUN]HWHJP[on the scale 5kg 10kg *OLJR[OH[[OL (+ KPZWSHÄLSKZOV^Z HUK[OL >,0./;(+ ÄLSK ZOV^Z HUK RLMVYSP[[SLHKQZ[TLU[PMULJLZZHY

3-2

95000 75000

For little adjustent

7YLZZ[OL :7(5 RL` ;OLUYLTV]L[OL^LPNO[ZMYVTZJHSL

CHAPTER 3 CALIBRATION

7ZO[OL4LTVYZ^P[JOVU 7>)!7… [VTLTVYPaL[OL(+KH[H :LHSV[OL4LTVYZ^P[JOHNHPU

3-3

PROGRAM MODE
4.1 PROGRAM MODE ENTRY / EXIT
1. Ensure that the initial screen is displayed, And press the Return button on the screen.
Note: The contents of the initial screen may KPLYKLWLUKPUNVU[OLZL[[PUNZVU`VY machine.

CHAPTER 4 PROGRAM MODE
4

2. The “Menu” screen is displayed. Then, press the [PROGRAM] button.

The program menu selection screen is
displayed. To turn pages, press [b] or [a].

4-1

CHAPTER 4 PROGRAM MODE
Note: ;VL_P[[OL7YVNYHT4VKLWYLZZ[OL B:(3,:DI[[VU
4-2

PLU DATA
5.1 PLU DATA
1. Press the “PLU” icon on the menu selection screen.

CHAPTER 5 PLU DATA
5

The “PLU” screen is displayed. To turn pages, press [b] or [a].

2. Select a desired PLU by pressing the JVYYLZWVUKPUNÄLSKHUKWYLZZ[OL [DETAIL] button.

1 2

5-1

CHAPTER 5 PLU DATA
3. The “PLU Detail (Sales)” screen is displayed. To edit the PLU name, press the name ÄLSK
4. The “PLU Name Edit” screen is displayed. Edit text according to the procedure described in Appendix “Text Editing”.
5. Press the “SALE 1” tab to display the “PLU Detail (Sale 1)” screen. The screen below shows that “Sales Mode” is set for selling weighing products.
5-2

CHAPTER 5 PLU DATA

SALES MODE
UNIT PRICE / FIXED PRICE OPEN PRICE FIXED WEIGHT TARE TAX
MARKDOWN MODE
M/D AMOUNT 2nd TARE

Press [<] or [>] to select a desired sales mode. 0: Weight (for selling weighing products) 1: Fix price (for selling fixed price products) 2: Weight fix price (for selling weighing fixed price products) 3: Fix unit price (for selling fixed unit price products) 4: Weight (100 g) (when the setting of the unit price per 100 g is needed in
accordance of the laws of a country) 5: Fix unit price (minus) (when the setting of the minus sale is needed in
accordance of the laws of a country)
Enter the unit price or fixed price and press this field.
Press [<] or [>] to select whether or not to allow an open price system.
0: Yes 1: No Enter the fixed weight and press this field.
Enter the tare weight and press this field. Enter a numerical value and press this field. Press [<] or [>] to select a desired markdown mode.
0: Normal price 1: Special price 2: Amount discount for total price 3: Percent discount for total price 4: Special unit price 5: Amount discount for unit price 6: Percent discount for unit price
Enter the markdown amount or percentage and press this field.
Enter the tare weight, and press this field.
Press the “UNIT TYPE” field to display the “Fix Price Symbol” screen. Then, press a desired field for selection.

UNIT TYPE

QTY TARE LOWER WEIGHT UPPER WEIGHT
FORCED TARE

Enter the packed quantity and press this field. Enter the tare percentage and press this field. Enter the lower weight limit and press this field. Enter the upper weight limit and press this field. Press [Yes] or [No] button to select whether or not to use the forced tare function.
5-3

CHAPTER 5 PLU DATA
6. Press the “SALE 2” tab to select the second sale related screen.

ITEM POINT FLAG
POINT TYPE POINTS

DESCRIPTIONS Press [<] or [>] to select whether or not to use the point flag. 0: OFF 1: ON Press [<] or [>] to select a desired point type. 0: Weight 1: Fixed weight Enter a desired number and press this field.

7. Press the “MSG.” tab to select the message related screen.

7YLZZHKLZPYLKÄLSKMVYZLSLJ[PVU

5-4

9. The “Extra Message” screen is displayed. 7YLZZHKLZPYLKÄLSKMVYZLSLJ[PVU
The selected message has been registered.

CHAPTER 5 PLU DATA
9.

10. Press the “IMAGE” tab to display the “PLU / Detail (Image)” screen.
7YLZZHKLZPYLKÄLSKMVYZLSLJ[PVU

5-5

CHAPTER 5 PLU DATA
12. The “Image” screen is displayed. Press a desired image for selection.
13. The selected image has been registered. Press [NO PRINT] or [PRINT] in the ¸:HML/HUKSPUN0THNL¹ÄLSK[V select whether or not to print the image.
7YLZZHKLZPYLKKPZWSH`PTHNLÄLSK
15. The Display Image screen is displayed. Press a desired image for selection. Note: To use images stored in the USB memory, press [STORAGE] key. The movie ÄSL^P[O[OLMVYTH[VM47,._ :=.(4IWZ-7:JHUHSZVILZLK ;OLUWYLZZ[OLB:,;DI[[VU
5-6

16. The selected image has been registered. Press [NO PRINT] or [PRINT] in the ¸:HML/HUKSPUN0THNL¹ÄLSK[VZLSLJ[ whether or not to print the image.
17. Press the “PRINT” tab to display the PLU / Detail (Print) screen.

CHAPTER 5 PLU DATA

ITEM 1st LABEL FORMAT No. (M) 2nd LABEL FORMAT No. 1st LABEL FORMAT No. (A)
1st LABEL PRINT
2nd LABEL PRINT

DESCRIPTIONS
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Press [ < ] or [ > ] to select whether or not to print the first label. 1: Yes 2: No Press [ < ] or [ > ] to select whether or not to print the second label. 1: Yes 2: No

5-7

CHAPTER 5 PLU DATA
18. Press the “DATE” tab to display the PLU / Detail (Date) screen.

ITEM PACK DATE PRINT
PACK TIME PRINT PACK TIME DATA SB DATE PRINT
SB TIME PRINT
SB TIME DATA SHELF LIFE (days) USE BY DATE PRINT UB DATE DATA

DESCRIPTIONS
Press [YES] or [NO] in this field to select whether or not to print the packed date. Press [<] or [>] to select a desired pack time printing method. 0: No print 1: Designated time 2: System clock time This field is available only when “1: Designated time” is selected in “PACK TIME PRINT”. Enter the time and press this field. Press [YES] or [NO] in this field to se lect whether or not to print the sell-by date. Press [<] or [>] to select a desired sell-by time printing method. 0: No print 1: Designated time 2: Relative time This field is available only when “Yes” is selected in “SB TIME PRINT”. Enter the number of hours and press this field. This field is available only when “Yes” is selected in “SB DATE PRINT”. Enter the number of days and press this field. Press [YES] or [NO] in this field to select whether or not to print the use-by date. This field is available only when “Yes” is selected in “USE BY DATE PRINT”. Enter the number of hours and press this field.

19. Press the “CODE” tab to select the PLU / Detail (Code) screen.

CHAPTER 5 PLU DATA

ITEM ITEM CODE REG CODE
POS FLAG
BARCODE
POS REFERENCE

DESCRIPTIONS Enter an item code and press this field. Enter the register code and press this field. This field is available only when “1: PLU File” is selected in “POS REFERENCE”. Enter a POS flag number and press this field. Enter a barcode number and press this field. Press [<] or [>] to select a desired reference method. 0: Refer 1: PLU file This field is available only when “1: PLU File” is selected in “POS REFERENCE”. Press this field to display the Barcode Type screen, and press a desired PLU type for selection.

BARCODE TYPE

Press this field to display the Barcode Format screen, and press a desired barcode format for selection. POS FORMAT (WGT)
5-9

CHAPTER 5 PLU DATA

TRACE ENABLE DEPARTMENT No. GROUP No.

Press [YES] or [NO] in this field to select whether or not to enable a traceability function. Press this field to display the Department screen. To set a department, press a desired field on the list, or press the “DEPARTMENT No.” field after numerical entry. Press this field to display the Group screen. To set a group, press a desired field on the list, or press the “GROUP No.” field after numerical entry.

63(&,),&$7,216
.1 63(&,),&$7,216

&+$37(563(&,),&$7,216

ITEM 02′(/ 6,=(
3/$77(56,=(
&$3$&,7<
32:(56833/< 32:(5 &2168037,21 ,2,17(5)$&( :L)L 7(03(5$785(

6/*1 [[PP c:[‘[+

&217(17 6/*#
[[PP c:[‘[+

6/*) [[PP c:[‘[+

[PP OEOEH OEOENJNJH JJ OEOEH OEOENJNJH JJ
$&9$&

PP

:c:RUNLQJ

,$%,7 Ethernet x 1chUSB 2.0 x 2ch

:L)LDEJQch ¥a¥

44 SANNO-CHO, SHOG OIN, SAKYO-KU KYOTO, 606-8392 JAPAN PHONE: 81-75-771-4141 FACSIMILE: 81-75-751-1634 URL: http://www.ishidajapan.com

Design and specifications are subject to change without notice.

References

• ishidajapan.com - This website is for sale! - ishidajapan Resources and Information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>