VERSACHOCK VCWINCHKIT Winch Kit for Tilting Davits Instruction Manual
- June 4, 2024
- VERSACHOCK
Table of Contents
Manual
Manual for Winch Kit
The validity, product images
Please read this entire manual carefully before installation or usage. This
manual is valid for the following VersaChock products from 1st-Relief:
– Tilting Davit Winch Kit
Article number: 1st23VCWINCHKIT
Specifications
The custom winch kit is designed specifically for use with VersaChock brand Tilting Davits. Assists in loading dinghies onto tilting davits with the included hand-operated winch. It is removable and easily installs with no tools by simply inserting the included square tube through the winch arms and into the tilting davit arms. Winch can be mounted on top or on the backside of main support arms with included hardware.
2.1 Construction
– High-Density Polyethylene (HDPE) main support arms
– Ratcheting hand winch with 610 cm (240 inch) x 4,76 cm (1 – 7 / 8 inch)
strap
– Square aluminium tube 122 cm (48 inch) x 5,08 cm (2 inch)
– stainless steel hitch pins for retaining tube
– Maximum pulling capacity 160 kg (350 lbs)
– Designed for use with VersaChock brand tilting davits
Installation / Important Notes
Please note the following important notes:
– We strongly recommend that the product specification, use and installation
be checked by a professional technician before purchase and that the
installation is carried out by the same person.
– This manual is for advice only. THERE ARE TOO MANY HULL VARIATIONS IN ORDER
TO SPECIFY AN EXACT INSTALLATION OR AN INSTALLATION LOCATION FOR EVERYONE.
– Not intended for use in extreme conditions (i.e.: high forces from water,
wind, etc.)
– Before each use, make sure that the hitch pins of the support tube are
securely inserted.
– Check the integrity of the hull, including hull thickness, chine, and
stringer locations, making sure proper support will be provided.
– Rinse with fresh water after each use, as saltwater and other contaminants
can cause staining, even though we use the most corrosion-resistant materials.
– Under no circumstances should a person/s or animal be allowed in watercraft
whether loading or in the stored position.
– Do not add additional gear, etc. that may subject the watercraft to be over
the maximum weight capacity.
– Always pull the drain plug when stored to prevent excess water to
accumulate, which could cause excess weight.
– Be sure the attachment bolts are secure before each use.
– FAILURE TO FOLLOW THE ABOVE MAY RESULT IN DAMAGE, LOSS, OR SERIOUS INJURY!
Tips for the operation of the tilting Davit
4.1 Get Familiar with your Davit
4.2 Using your Winch Kit
Please note the information from the previous chapters of this manual.
4.2.1 Winch Kit – Location
The winch can be located on top or on the back of the main support arms by
removing bolts.
4.2.2 Insert Tube
Insert support tube through support arms.
4.2.3 Insert hitch pins
Insert support tube through davit arms and insert hitch pins to keep tube from
slipping out.
4.2.4 Attach Strap
Extend the strap under the dinghy, then around the top of the dinghy, and
attach the strap to dinghy rope (or D-ring if equipped).
NOTE: attaching the strap to side closest to boat, allows for easy
attaching and removal of the strap without having to reach over the dinghy.
4.2.5 Use ratchet arm
Use ratchet arm to assist loading dinghy onto davits
NOTE: Some manual assistance is typically required to load the dinghy.
4.2.6 Fixing the Davits
Tilt davits down, then reinsert hitch pins / lynchpins in each davit.
4.2.7 Install tie downs
Install the tie-downs.
4.2.8 Enjoy
Enjoy the usage of your tilting Davit.
Additional information, liability
5.1 Updates and other tips
For updates and additional tips, see:
https://www.1st-relief.com/en/equipment-hardware/brackets-davits-load-
securing-devices/
5.2 Liability
Installation and use of this product are at the customer’s own risk. We
strongly recommend that the product specification, use, and installation be
checked by a professional technician prior to purchase and that the
installation be carried out by them. Your safety and customer satisfaction are
our top priorities!
5.3 Acknowledgments
Thank you for choosing our products. Together with our manufacturer
VersaChock, we strive to deliver the most innovative products of the highest
quality. VersaChock products are manufactured by Jefferson Design Inc. of
Tampa Bay Florida. We hope you will enjoy our products for many years to come.
We look forward to your Comments and feedback!
Your satisfaction is our number one priority! If you have any questions,
please contact our customer service office@1st-relief.com
FN: 552603b (LG f. ZRS Graz)
VAT No.: ATU76757859
Bank: RB Graz-Mariatrost
Swift/BIC: RZSTAT2G223
IBAN: AT08 3837 7000 0420 9185
Handbuch VC Winch Kit EN 1_0.docx
1st-Relief GmbH Schulgasse 5
8010 Graz, Austria