NoCry ‎NCS-10NM Cordless Electric Screwdriver User Manual

: October 30, 2023
: NoCry

NoCry ‎NCS-10NM Cordless Electric Screwdriver

NoCry-‎NCS-10NM-Cordless-Electric-Screwdriver-product

GENERAL POWER TOOL SAFETY WARNINGS

READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS

Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Before use, be sure everyone operating this tool reads and understands all safety instructions and other information in this manual. Review frequently prior to use and when instructing others.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (with a power cable) power tool, and to battery-operated tools (without a power cable).

WORK AREA SAFETY

KEEP THE WORK AREA CLEAN AND WELL-ILLUMINATED. Untidy or unlit work areas can result in accidents.
CONSIDER THE WORKING ENVIRONMENT. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
KEEP CHILDREN AND BYSTANDERS AWAY while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

GUARD AGAINST ELECTRIC SHOCK. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
AVOID BODY CONTACT with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
DO NOT EXPOSE TO RAIN AND WET CONDITIONS. Water entering a power tool will increase the risk of electric shock.
DON’T ABUSE CORD. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, and moving parts. Damaged or entangled cords increase the risk of electric shock.
USE EXTENSION CORD WHEN OUTSIDE. When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
USE RESIDUAL CURRENT DEVICE IF DAMP CONDITIONS ARE UNAVOIDABLE. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

STAY ALERT. Watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Protective equipment such as safety glasses, gloves, dust masks, non-skid safety shoes, hard hats, and/or hearing protection used for appropriate conditions will reduce personal injuries.
PREVENT UNINTENTIONAL STARTING. Ensure the switch is in the off-position before connecting to the power source and/or battery pack, picking up, or carrying the tool. Carrying power tools with your finger on the switch or connecting the appliance to the mains when it is switched on, can lead to accidents.
REMOVE ANY ADJUSTING KEV OR WRENCH before turning the power tool on. A wrench or a key left attached to a rotating part of a power tool may result in personal injury.
DO NOT OVERREACH. Keep proper footing and balance at all times to keep control in unexpected circumstances. Taking unnecessary risks may cause injury or harm.
DRESS PROPERLY. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from hot and moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
DUST SAFETY. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection systems can reduce dust-related hazards.

POWER TOOL USE AND CARE

DON’T FORCE THE TOOL. Do not overload the power tool. Use the correct power tool for your application in the manner it was designed. The correct power tool will do a better and safer job for which it was designed than for those for which it wasn’t.
DO NOT USE A MALFUNCTIONING TOOL. Do not use the power tool if the switch does not turn it on and/or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
DISCONNECT TOOLS. Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
STORE IDLE POWER TOOLS out of the reach of children and do not allow persons unfamiliar with the power tool, or these instructions, to operate the power tool. Power tools are dangerous in the hands of untrained users.
MAINTAIN POWER TOOLS. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use? Many accidents are caused by poorly maintained power tools.
KEEP YOUR CUTTING TOOLS SHARP AND CLEAN. Carefully maintained cutting tools with sharp cutting edges will jam less and are easier to control.
CORRECT USE OF ACCESSORIES AND ATTACHMENTS. Use the power tool, accessories, and attachments in accordance with these instructions, taking into account the working conditions, and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Note: Refer to the WORK EXAMPLES section of this manual for further details.
ONLY CHARGE THE BATTERIES WITH CHARGERS THAT ARE RECOMMENDED BY THE MANUFACTURER. A charger that is designed for a certain type of battery may pose a fire risk if it is used with other types of battery.
USE THE CORRECT BATTERIES IN THE ELECTRIC TOOL. The use of other batteries may result in injuries and a risk of fire.
KEEP UNUSED BATTERIES AWAY from paper clips, coins, keys, nails, screws, and any other metallic objects that could cause a short circuit between the contacts. A short circuit between the battery contacts may cause burns or a fire.
UNDER ABUSIVE CONDITIONS, LIQUID MAY EJECT FROM THE BATTERY; avoid physical contact with it. If contact accidentally occurs, flush the exposed area with water. If liquid contacts with eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
IN CASE OF A DAMAGE AND IMPROPER USE, VAPORS MAY BE EMITTED FROM THE BATTERY. The battery can set alight or explode. Ensure that the work area is well ventilated and seek medical attention should you experience any adverse effects. The vapors may irritate the respiratory system.

SERVICE

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Hold the equipment by the insulated handles when carrying out work during which the screw or the plug-in tool could strike concealed power cables. Contact with a live cable may also make the metal parts of the equipment live and cause an electric shock.

SAFETY WARNINGS FOR ELECTRIC SCREWDRIVER DESCRIPTION OF SYMBOLS

Pay attention to all the signs and symbols shown in these instructions and on your tool. Make a note of these signs and symbols. If you interpret the signs and symbols correctly, your work with the machine will be safer and better.

IMPORTANT

READ THE INSTRUCTIONS BEFORE STARTING THE MACHINE

WEAR SAFETY GOGGLES

WEAR EAR PROTECTION

WEAR GOOD QUALITY, STRONG GLOVES

ALWAYS USE BREATHING APPARATUS WHEN MACHINING MATERIALS THAT GENERATE DUST

END-OF-LIFE MACHINES CONTAIN VALUABLE MATERIALS AND THEREFORE THEY SHOULD NOT BE PLACED IN HOUSEHOLD WASTE. WE WOULD ASK YOU TO PLAY YOUR PART IN PROTECTING RESOURCES AND HELP PROTECT THE ENVIRONMENT BY RETURNING THIS MACHINE TO A RETURN POINT (IF THERE IS ONE AVAILABLE) WHEN IT REACHES THE END OF ITS LIFE.

PROPER USE

The cordless screwdriver is designed for tightening and undoing screws.
The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/ operator and not the manufacturer will be liable for any damage or injuries caused as a result of this.
Please note that our equipment has not been designed for use in commercial. trade or industrial applications. Our warranty will be voided if the machine is used in commercial. trade or industrial businesses or for equivalent purposes.

TECHNICAL DATA

Model	NoCry NCS-lONM Cordless Screwdriver
Idling speed	0-230 rpm
Bit chuck diameter	1/4 inch
Torque settings	5+1
Maximum torque	130.5NN.m.m(h(saorfdti
Rotation direction	clockwise & counter-clockwise
Motor power supply	rechargeable 7.2V DC/1.5 Ah Lithium Ion

The sound and vibration values have been determined in accordance with EN80745. The vibration value changes according to the area of application of the screwdriver, and may exceed the specified value in exceptional circumstances.

BEFORE STARTING THE EQUIPMENT

Be sure to read the following information before you use your cordless screwdriver for the first time:

Charge the battery pack with the charger supplied. Use only the NoCry charging adapter provided with the product. Using a different charger could result in electrical issues, injury, and/or property damage.
Only ever use screwdriver bits that are suitable for the purpose and in faultless condition.
Always check for concealed electric cables, and gas and water pipes when drilling and screwing in walls.

SCREWDRIVER IMAGES

NoCry-‎NCS-10NM-Cordless-Electric-Screwdriver-fig-8

PART LIST
1. Bit Chuck 2. Torque selector 3. ON/OFF switch 4. Clockwise/Counter- clockwise selector switch 5. Lamp 6. Charging socket 7. Battery capacity indicator 8. Battery charger 9. Charging cable

OPERATION

CHARGING THE BATTERY (FIG. 2)

The battery is protected from exhaustive discharge. An integrated protective circuit automatically switches off the equipment when the battery Is flat. In case the bit chuck will cease to turn.
Never charge batteries unattended. When charging lithium-ion batteries, you must always remain in constant observation to monitor the charging process and react to any potential issues that may occur.
Warning! Do not press the ON/OFF switch anymore if the protective circuit has been actuated. This may damage the battery.

Check your mains voltage is the same as that marked on the rating plate of the battery charger. Plug the battery charger in the plug socket and connect the charging cable to the socket. (8)

LED indications:

Red LED illumination: Charge the electric screwdriver.
Yellow and red LED illuminated: Battery has sufficient charge.
All LED illuminated: The battery is fully charged.

If the battery pack fails to charge , please check whether there is voltage at the socket/ outlet. and that there is proper contact between the tool and the battery charger points.
If the battery still fails to charge, contact us at wecare@nocry.com.
Timely recharging of the battery pack will increase the battery life of the product. Never allow the battery pack to become fully discharged, as it might cause defects in the operation.

CHANGE OF DIRECTION SWITCH (FIG 3. / ITEM 4)

The sliding toggle above the ON/OFF switch is for setting the direction of rotation of the cordless screwdriver, and for preventing the cordless screwdriver from being switched on inadvertently. You can select between clockwise and counterclockwise rotation. Change the direction of rotation only when the equipment is at a standstill. Failure to do so may damage the gearing. When the toggle is in the middle position, the ON/OFF switch is blocked.

ON/OFF SWITCH (FIG. 3 / ITEM 3)

Press the ON/OFF switch to switch the cordless screwdriver on. Release the ON/OFF switch to switch the tool off.

LED LAMP

The LED lamp (5) can be used in poor lighting conditions to illuminate the area where you want to screw.

TORQUE SETTING (FIG. 3)

The cordless screwdriver is fitted with a mechanical torque selector. The torque for a specific size of screw is selected by rotating the front of the screwdriver (2). The correct torque depends on several factors:

The type and hardness of the material in question
The type and length of the crews being used
The requirements need to be met by the screwed joints.

The clutch will disengage with a grating sound to indicate when the set torque is reached.

CHANGING THE TOOL (FIG. 6)

Important! Set the sliding toggle to the center position whenever you carry out work (for example changing the inserts, maintenance work, etc.) on the cordless screwdriver.

SCREWDRIVING

We recommend using self-centering screws (e.g. Torx screws, recessed head screws) designed for reliable working. Be sure to use a bit that matches the screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of the screw.

CLEANING AND MAINTENANCE

Before any work on the machine itself, pull the mains plug. For safe and proper working, always keep the machine and ventilation slots clean.

CLEANING

Keep all safety devices, air vents, and motor housing free of dirt and dust as much as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
We recommend that you clean the device immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could damage the plastic housing of the tool.
Ensure that no water can seep into the device.

MAINTENANCE

There are no parts inside the tool which require additional maintenance. If the replacement of the supply cord is necessary, this must be done by an authorized service agent in order to avoid a safety hazard.

DISPOSAL AND RECYCLING

The unit is supplied in packaging to prevent it from being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system. Electrical products should not be discarded with household products. Electrical products used must be collected separately and disposed of at collection points provided for this purpose. Talk with your local authorities or dealer for advice on recycling.

WARRANTY

All NoCry products are inspected and tested to ensure their quality before leaving the factory. If you’re not happy with your NoCry product, please contact us within 30 days of receiving it at wecare@nocry.com to return it for free for a replacement product or to receive a full refund. The choice is yours.
Each NoCry electric product is warranted to be free of defects in material and workmanship for the period of FOUR years from the date of original purchase. Warranty does not cover normal wear and tear, abuse, altered products, modifications, and products that have been repaired or attempted to be repaired by others than No Cry. At NoCry’s discretion, a defective product will be repaired or replaced.
This warranty gives you specific legal rights but may be superseded by any other rights or warranties in effect, which may vary from state to state (or based on your local jurisdiction). If you think you might have a defective product, please contact us at wecare@nocry.com. Our customer care team will be happy to help and start the (free) procedure to determine whether your product is defective.
NoCry’s warranty applies to ON LY products being sold by Authorized Resellers. We regretfully will not provide any warranty for products sold by any other sources. Proof of purchase will be required to obtain a warranty. Please review the warranty carefully, and contact us if you have any questions.

HOW TO CONTACT NOCRV

We’re glad to have you join the NoCry community, and we hope you are happy with your new NoCry Cordless Screwdriver. If you have any questions or concerns, let us know by emailing wecare@nocry.com.
We’d also love to connect with you via social media. You can find us on Instagram, Facebook, and Pinterest by searching “NoCry Tools & Gear”.
US & CA Distribution by: NoCry, LLC. 10785 W. Twain Ave. Suite 210,
Las Vegas, 89135, NV, USA.
www.nocry.com
wecare@nocry.com
Batch Number: NCS-2021-01
Made in China 2022

Frequently Asked Questions

What is the maximum torque of the NoCry NCS-10NM Cordless Electric Screwdriver?

The maximum torque of the NoCry NCS-10NM Cordless Electric Screwdriver is 130.5NN.m.m(h(saorfdti).

What is the weight of the NoCry NCS-10NM Cordless Electric Screwdriver?

The weight of the NoCry NCS-10NM Cordless Electric Screwdriver is 1.27 lb.

What is the charging time for the NoCry NCS-10NM Cordless Electric Screwdriver?

The charging time for the NoCry NCS-10NM Cordless Electric Screwdriver is 3 hours.

Does the NoCry NCS-10NM Cordless Electric Screwdriver come with interchangeable bits?

Yes, the NoCry NCS-10NM Cordless Electric Screwdriver typically comes with a set of interchangeable bits. These bits can be easily swapped out to accommodate different screw types and sizes.

How long does the battery last on the NoCry NCS-10NM Cordless Electric Screwdriver?

The battery life of the NoCry NCS-10NM Cordless Electric Screwdriver depends on the usage and the specific model. Generally, it can last for several hours of continuous use on a single charge.

What is the purpose of the NoCry NCS-10NM Cordless Electric Screwdriver?

The NoCry NCS-10NM Cordless Electric Screwdriver is designed for tightening and undoing screws.

What is the maximum torque of the NoCry NCS-10NM Cordless Electric Screwdriver?

The maximum torque of the NoCry NCS-10NM Cordless Electric Screwdriver is 130. 5NN.m.m(h(saorfdti).

What is the weight of the NoCry NCS-10NM Cordless Electric Screwdriver?

The weight of the NoCry NCS-10NM Cordless Electric Screwdriver is 1.27 lb.

How long does it take to charge the battery of the NoCry NCS-10NM Cordless Electric Screwdriver?

It takes 3 hours to charge the battery of the NoCry NCS-10NM Cordless Electric Screwdriver.

What is the sound pressure level of the NoCry NCS-10NM Cordless Electric Screwdriver?

The LPA sound pressure level of the NoCry NCS-10NM Cordless Electric Screwdriver is 67 dB (A).

What should I do before using the NoCry NCS-10NM Cordless Electric Screwdriver for the first time?

Before using the NoCry NCS-10NM Cordless Electric Screwdriver for the first time, you should charge the battery pack with the charger supplied and only use screwdriver bits that are suitable for the purpose and in faultless condition.

Can I use the NoCry NCS-10NM Cordless Electric Screwdriver for commercial, trade or industrial applications?

No, the NoCry NCS-10NM Cordless Electric Screwdriver has not been designed for use in commercial, trade or industrial applications. The warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.