CLARKE18WD Summit Pro 18SQ Wet or Dry Vacuum Cleaner Instruction Manual

CLARKE18WD Summit Pro 18SQ Wet or Dry Vacuum Cleaner

Product Information: Summit Pro 18SQ

The Summit Pro 18SQ is a commercial wet and dry vacuum cleaner designed for indoor use only. It comes with a special grounding plug to reduce the risk of electrical shock in case of any malfunction. The vacuum cleaner comes with recommended accessories only and must be grounded at all times.

Safety Precautions

All operators should read and understand the following safety precautions:

1. Do not operate the machine without reading the user manual.
2. Always ground the machine before use.
3. Do not use the machine with hot liquids.
4. Always unplug the machine before servicing or leaving it.
5. Service the machine only when it is unplugged.

Attaching Handle

To attach the handle, follow these steps:

1. Remove the handle from the shipping position and remove the upper handle mounting screws from the machine.
2. Realign the handle as shown and replace screws & washers.
3. Attach rear hose dump Clamp (B).
4. Attach front mount Squeegee (C).

Operation of Wet & Dry Vacuum

To operate the vacuum cleaner:

1. Read the operator’s manual thoroughly before operating or servicing this machine.
2. For wet pickup, use the appropriate accessory and empty the recovery tank frequently.
3. For dry pickup, use the appropriate accessory and empty the recovery tank frequently.

Maintenance and Storage

To maintain and store the vacuum cleaner:

1. Unplug the machine from the power source.
2. Store the machine in an upright position in a dry area.
3. Store the machine with the squeegee assembly off the ground.
4. Store the machine with the vacuum head off the unit so that the tank can breathe.

This book has important information for the use and safe operation of this machine. Failure to read this book prior to oper-ating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories.

1. Do not operate machine:
   • Unless trained and authorized.
   • Unless you have read and understand operators manual.
   • In fl ammable or explosive areas.
   • With damaged cord or plug.
   • If not in proper operating condition.
   • In outdoor areas.
   • In standing water.
   • Without bag / fi lters in place.
   • With the use of extension cords.
2. Before operating machine:
   • Make sure all safety devices are in place and operate properly.
   • When using machine:
   • Do not run machine over cord.
   • Do not pull machine by cord or plug.
   • Do not pull cord around sharp edges or corners.
   • Turn power switch to “off “ prior to unplugging machine..
   • Do not unplug by pulling on the cord.
   • Do not stretch cord.
   • Do not handle plug with wet hands.
   • Keep cord away from heated surfaces.
   • Do not pick up burning or smoking debris such as cigarettes, matches or hot ashes..
   • Report machine damage or faulty operation immediately.
3. Before leaving or servicing machine:
   • Turn off machine.
   • Unplug cord from outlet.
4. When servicing machine:
   • An experienced technician should only perform service work.
   • Unplug cord from outlet.
   • Use manufacturer supplied or approved replacement parts.All operators shall read, understand and exercise the following safety precautions:

GROUNDING INSTRUCTIONS
!!! This machine must be grounded! Grounding provides the path of least resistance for electrical current. To reduce the risk of electrical shock should the machine malfunction, the machine has a special grounding plug. Do not remove the ground pin under any circumstances! ATTACHING HANDLE

1. Remove Handle (A) from ship position and remove upper handle mounting screws from machine.
2. Realign Handle (A) as shown and replace screws & washers.
3. Attach rear hose dump Clamp (B).
4. Attach front mount Squeegee (C).

OPERATION OF WET & DRY VACUUM

READ OPERATORS MANUAL THOROUGHLY PRIOR TO OPERATING OR SERVICING THIS MACHINE.
WET PICKUP

1. Remove vacuum head and remove the cloth or paper fi lter from vacuum, install the bubble buster.

2. While vacuum head is removed, check to make sure that the fl oat shut-off is unobstructed and fully functional.

3. Replace vacuum head and latch it in place.

4. Connect vacuum hose to inlet on the machine body.

5. Attach appropriate accessory tool for the job to be completed.

6. Plug power cord into a grounded outlet.
   Do not use an extension cord in conjunction with the standard power cord.

7. If using the front-mounted squeegee assembly, be sure that squeegee is attached to front of machine.

8. If using the front-mounted squeegee assembly, lower squeegee to the fl oor by depressing the top half of the pedal (rear of the machine) forward with your foot.

9. Turn power switch to “on” position.

10. During wet pickup, the fl oat shut-off will automatically prevent water from entering the recovery tank once the recovery tank is full.
    If foam develops in the recovery tank during wet vacuuming, use de-foamer chemical to help eliminate the foam. Foam will not activate the fl oat shut- off, and therefore, may cause vacuum motor damage.

11. To raise the squeegee assembly back to transport position, depress the bottom half of the pedal [rear of the machine] downward with your foot.
    Be sure that the handle is properly assembled on machine body prior to operating machine.
    This wet –dry vacuum includes the GV25014”bubble buster” blue nylon foam suppression bag. This bag must be used in all wet pickup applications. Failure to use the bag will void the warranty on the vacuum motor.

DRY PICKUP

1. Remove vacuum head and bubble buster, and be sure the cloth or paper fi lter is properly installed.
   Do not operate machine without bag or fi lter properly installed.

2. Replace vacuum head and latch it in place.

3. Connect vacuum hose to inlet on the machine body.

4. Attach appropriate accessory tool for the job to be completed.

5. Plug power cord into a grounded outlet.
   Do not use an extension cord in conjunction with the standard power cord.

6. Turn power switch to “on” position.

7. Check the fi lter bag periodically to see if it is full. For optimal performance, replace bag when it is 3/4 full.

DRAINING THE RECOVERY TANK

1. Unplug machine from power outlet.
2. Transport machine to nearest fl oor drain or bucket.
3. Remove drain hose from rear of machine. Remove ball plug from drain hose, and drain the contents of the tank.
4. After the contents have drained, remove the vacuum head and rinse recovery tank with clean water.
5. Replace the ball plug on the drain hose and hang hose back on the rear of the machine.
   To prevent odors in the recovery tank, remove the vacuum head when machine is not in operation to allow air to circulate.

MAINTENANCE

To keep the machine performing well for many years, please follow the following maintenance procedures.
Always confi rm that the machine is unplugged prior to performing any maintenance or repairs.

1. Drain and rinse recovery tank after each use.

2. Clean fl oat shut-off after each use.

3. Check bag to see if it is full after each use. Replace bag when it is 3/4 full.

4. Clean outside of machine with a mild cleaner.

5. Check power cord for any damage.

6. Clean squeegee blades with a cloth.
   Do not use your fi ngers to wipe the blades!

7. Check vacuum hose for holes and clogs.

8. Lubricate wheels, casters and axles with a water resistant lubricant every month.

9. Check machine for loose or missing nuts and bolts, and replace as necessary.
   After each use in a wet pick-up application, remove the GV25014 “Bubble Buster” blue nylon foam suppression bag and rinse it with clean water. This will aid in preventing any build-up which can reduce air fl ow.

STORAGE

1. Unplug machine from power source.
2. Store in upright position in a dry area.
3. Store with squeegee assembly off the ground.
4. Store with vacuum head off unit so that tank may breathe.

References

• CustomerZone: Buy Nilfisk, Advance, Clarke, and Viper Parts, Accessories, and Machines | Nilfisk Official Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>