LOFTER 4 Pack Submersible LED Lights User Guide
- June 4, 2024
- LOFTER
Table of Contents
LOFTER 4 Pack Submersible LED Lights
Thank you for your purchasing LOFTER submersible LED lights
Please read this user guide carefully before operating the submersible LED
lights, and properly keep the guidefor future use.
If you have any problem in using this product, please contact with us soon by
email as below. We will supply the best solution for you to any problem in 24
hours.Any advice will be collected and we will do our best to improve.
- service@belofter.com
- @LOFTER
- www.belofter.com
PRODUCT DETAILS
Submersible LED Light Detail
Remote Control Detail
Package Contents
- 4 x Pool lights
- 16 x Suction Cup
- 1 x Manual
- 2 x RF Remote Control
Installation
- Twist the back cover to open it according to the”OPEN” direction
- Insert the TWO raised pillars on the back cover into the groove of the battery cover to open it.
- Insert 3 AA batteries ( Not Included ) and twist the battery cover .
- Please twist the light until ii can not be twisted any further, to make it fully waterproof before putting underwater.
- Tighten the back cover and use the remote control to use this product.
PRECAUTIONS FOR USE
Tips for RF Remote Control
- Please remove the plastic insulating film on the bottom of the remote before using it.
Tips for Suction Cups
- Please clean the surface before attaching, make sure there is not any stuff between the surface and suction cup, especially remember to remove the lubricant like shower cream, moss, etc.
- Not recommended for underwater use.
Tips for Magnet
- The magnet is strong, but it’s better to apply it on a pure iron surface, alloy may reduce the absorb effect.
TECHNICAL SPECIFICATIONS
To know the product better and use Submersible LED Light properly, please read the table below:
FCC Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
C-1028rf remote control, there are two versions of fixed code format and
rolling code format.
This is a highly integrated chip IC technology to develop circuit board to do
the remote control, the remote control technology is mature, excellent
performance, launch
Large power, the use of sound meter device (SAW) frequency stability, with
strong antiinterference, high agility long distance, good stability and
consistency, low power consumption
The advantages of low cost. Suitable for all kinds of wireless remote control
products
- Size: 86X52X7mm
- Number of keys: 28
- Battery type: CR2025
- Ambient Temperature:- 20 ° -50 C
- Relative humidity :& LT; 90%
- atmospheric pressure: 86-106kpa Ming plate
- material : PVC
- storage temperature :-20-50 degrees
- Operating current :12mA
- Static current :2uA
- Rated operating voltage :3V
- Operating voltage range: 2.4-3.2V
- Operating distance: 15m
- directivity :360 full Angle
- key force :0.8-1.5N
- Key Load life : 300,000
- times free drop test : 80cm electrostatic environment test + 15KV constant
- humid heat test: 40 degrees Celsius
- Circuit Board material: Carbon oil board (fiberboard can be customized)
- The operating voltage is 6V
- Standby current 0. Lua
- Operating current 5-7mA
- Measured frequency 433.80mhz ~ 433.90mhz (frequency offset 30~20KHZ)
- Full transmit power attenuation 5.2 grid (-5.42~-6.0ldBm)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>