CMS Electracom FR210PB Series Lithium Battery Instruction Manual

FREEDOM SERIES FR210PB, FR210CS &
FR210DS INSTRUCTION MANUAL

IMPORTANT SAFETY INSTRUCTIONS

WARNING
This symbol indicates information concerning your personal safety.
CAUTION
This symbol indicates information on how to avoid damaging the unit.
IMPORTANT
This symbol indicats tips and information about FR210PB, FR210DS, FR210CS Operation.

CAUTION/WARNING

• Read all instructions before using the product.
• To reduce risk of injury, close supervision is necessary when the product is used near children.
• Use of an attachment not recommended or sold by power bank manufacture may result in a risk of fire, electric shock, or injury to persons.
• To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting power pack.
• Do not operate the unit with a damaged cord or plug, or a damaged output cabled.
• Do not use if the unit has been damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not disassemble FR210PB, FR210CS, FR210DS, take it to a qualified service person when a service or repair is required. Incorrect assembly may result in a risk of  fire or electric shock.
• Do not exposed to water.
• This unit may become hot when recharging, handle with care.
• Do not leave in hot conditions 35C or above e.g., left sitting in hot car, left siting in direct sunlight.
• Do not operate unit outside of specified conditions.
• This unit contains Li-ion 18650 or equivalent cells.
• Do not expose to heat or throw in fire.
• Do not attempt to modify.
• Be careful when unpackaging the unit. Do not use sharp objects when removing the packaging as this may cause scratches to the unit.

Specification

Specification FR21 OPB
Model: FR210PB
Battery cells: Li-ion 18650
Battery Capacity: 9540mAh*(206Wh)(+/- 5%)
Input (12pin): DC 20V/7.5A (max) via Charging Station (FR210CS), DC 20V/5A (max) via Docking Station (FR210DS)
Type-C output: DC 5V/3A, 9V/3A, 12V/3A 15V/3A, 20V/5A (PD3.0 100W)
Type-A output: DC 5V/3A, 9V/2A, 12V/1.5A (QC3.0 18W)
Total output: 118W (Both ports combined)
Dimensions: 251.8mm (L) x 151.4mm (W) x 38.1mm (H)
Weight: 1.53KG
Operation Temperature: 5-35C
Packaging Content: 1 x FR210PB (Release Key included with FR210PBK variant)

Specification FR21 OCS
Model: FR210CS
Power Input: 20V/7.5A Power output: 20V/7.5A
Dimensions: 326.4mm (L) x 199.3mm (W) x 92mm (H)
Weight: 1.88KG
Operation Temperature: 5-35C
Packaging content: 1 x FR210CS, 1 x AC Power Cord, 1 x Power Supply (20V/7.5A)

Specification FR21 ODS
Model: FR210DS
Power Input: DC Jack 20V/5A, USB C 20V3A
Type-C output: DC 5V/3A, 9V/3A, 12V/3A 15V/3A, 20V/5A (PD3.0 100W)
Type-A output: DC 5V/3A, 9V/2A, 12V/1.5A (QC3.0 18W)
DC OUT 1: (XT60 connector) 18-25.2V (Cell voltage) 16-18A
DC OUT 2: (XT60 connector) 12V,18V,20V,24V/11A
Total output: 300W combined (350W DC OUT 1 for 1 – 2 minutes at a time)
Dimensions: 280.5mm (L) x 152.2mm (W) x 31.6mm (H)
Weight: 0.92KG
Operation Temperature: 5-35C Packaging content: 1 x FR210DS

Product Overview

FR210PB

1. LED Charge level indicator

2. USB C Port

3. USB A Port

4. Power Button

5. Push Button Release
   (Key version depicted below)

6. 12pin connector

FR210CS

1. Power Indicator
2. D.C. Jack — Power In (20V/7.5A)

FR210DS

Setting Up FR210CS
IMPORTANT
Setting up

1. Plug the AC cord into the power supply.
2. Plug the AC plug into an outlet.
3. Plug the power out lead from the power supply into the DC jack on at the back of FR2CS. Power indicator will illuminate green.

Using

To recharge the power bank (FR210PB), place it into the dedicated charging station (FR210CS). The power bank will be recharged via the 12pin connector the end of each unit. The Charging Station can hold and charge up to five power banks (FR210PB) simultaneously.
Refer to the below table for charging times in relation to number of units charging.

IMPORTANT
Setting up

1. Position and screw the Docking Station (FR210DS) into place on the underside of the workstation using 4qty 4G screw. There are 4 screw fixing locations on the  underside of the Docking Station.
   

2. Connect compatible CMS products to the output ports on the rear of the unit.
   Note: if you are using DC OUT 2 make sure the correct voltage is selected before plugging in compatible devices.

Using FR210DS

Slide the Power Bank (FR210PB) into the Docking Station (FR210DS) as shown. You will hear an audible clicking sound when locked in. The power button on the docking station may need to be pressed to power on the unit. All 4 LED’s will illuminate when on to display charge level of docked power banks.
Multiple Power Banks can be stacked to increase runtime as shown below.

IMPORTANT- Maximum Outputs
To disengage Power Bank(s) either press the push button release at the front of the unit you wish to disengage or use the key and turn in a clockwise direction. When released the Power Bank will spring out/forward slightly. Note some force may be required when pressing push release button in.

The docking station (FR210DS) is capable of recharging the docked power bank(s) (FR210PB) via the 20V/7.5A DC IN JACK. The Recharge times will be slower compared to using the charging station (FR210CS). Note that when recharging all output ports will be disabled.

Refer to the below table for recharging times in relation to the number of docked power banks.

IMPORTANT— Unboxing FR210PB will first need to be charged via FR210DS or FR210CS when first unpackaged. Refer ‘Using FR210CS’

The power bank (FR210PB) can recharge any USB C or USB A compatible device(s). Simply plug in the device and the power bank will auto detect that a device has been plugged in and power on. Four white LED’s will illuminate to indicate the power banks charge level.
The power button can also be pressed to turn on the power bank and display charge level. To turn off the power bank long press the power button for 10 seconds, the 4 LED’s will cycle through 3 times before turning off. As FR210PB charges your device each LED will go out systematically until the power bank is depleted.

The power bank connected to the devise(s) will become the main unit and will display charge level via 4 LED’s. The second unit will become the slave and LED’s will remain  off.

IMPORTANT – Slave Unit If the slave unit power button is pressed in this setup the charge level displayed via 4 LED’s may not be correct.

User Maintenance Instructions

Important — Cleaning
When cleaning FR210PB, FR210CS & FR210DS do not spray cleaner directly onto unit. Spray onto cloth and wipe down the unit.
Only spray enough cleaner that the cloth is just damp to the touch.
When cleaning FR210CS or FR210DS disconnect from mains power before wiping down. Do not spray cleaner directly onto unit. Spray onto cloth and wipe down the unit. Only spray enough cleaner that the cloth is just damp to the touch.

Moving & Storage Instructions
Important – Long Term Storage
When storing FR210PB for extended periods of time you MUST discharge and recharge the unit at least every 6 months to maintain the integrity of the batteries.
Disposal of Product
This product contains lithium-ion batteries. At the end of the product life cycle the freedom unit must be disposed off at an appropriate waste facility.
Do not dispose of FR210 Series in general waste.

FR210PB
All four LED’s flashing
simultaneous| The over-current protection has activated during discharging.| Remove the over-loading device, the output  will recover by pressing the power button or recharging the unit via charging station (FR210CS)to rest.
The over-temperature protection is activated during charging.| The Unit stopped charging as the device  operating temperature has been exceeded.  The unit will resume function after returning  to operating temperature range.
The power bank cannot
be charged.| Check FR210CS is plugged in with power available.| Ensure FR210CS is plugged in with power  available LED illuminated.
12 pin connectors may not be making good contact.| Check that no debris is impeding recharging  via the 12- pin connector. Remove and readd  the power bank.
Your plugged-in
device(s) are not
charging.| There is no capacity left.| Re-charge the power bank.
The firmware is in protection mode.| Recharge via FR210CS to reset.
Trying to recharge immediately after rapid discharge.| The temperature of the cells may be too high, battery protection will not allow the unit
to charge until cells are at a safe operating  temperature.
Allow some time for the unit to cool down  before attempting to recharge.
Unit run time is low| The capacity left is low| Re-charge the power bank.
The working current of devices is larger.| Battery degradation over time/usage
Battery is close to end of life| Battery degradation over time/usage
Unit is Unresponsive| The Unit software is frozen/unresponsive| Press and hold RESET button for 10  seconds (Rest Button located on the  underside of the unit).
FR210CS

Power Available LED not on| The unit may not be plugged in correctly| Check that the unit is plugged in correctly and  power point is active
FR210DS
4 LED’s Fast Flashing| The Over-current protection is
activated, for USB A or USB C port is
overloaded| Remove the overloading device, the USB port(s) will recover by pressing power button or recharging to rest.
1 Red LED on| The over-current protection is activated, DC OUT 1 or DC  OUT 2 is overloaded| Remove the overloading device(s), Press Power  Button to recover. Auto recover will occur after 30 minutes
Unable to output or turn
on| Perhaps the 12-pin connector isn’t making good contact| Remove and readd FR210PB
12 pin connector made incorrect contact, activated protection.| Recharge to recover (DC IN at rear)
USB C port and DC OUT
ports won’t provide
output simultaneously| 2nd Power Bank (FR210PB) required| Install second Power Bank (FR210PB). If already  installed, try removing and readding.
Unable to discharge or recharge| A High rate of discharge has just been applied increasing the
temperature of the cells. Over temperature protection  activated to protect the cells| Wait for the cells to cool down before attempting to recharge or discharge
4 LED’s immediately start to cycle  through 3 times before unit turns off after docking FR210PB| Residual charge left in capacitors or FR210DS trigger low  power mode and the unit turns off.| Rest by recharging via 20V, 7.5A DC IN

FR210DS Wiring Example: Mobile Workstation

Connected devices:
1 x HP E243i Monitor @ 25W/h (typical)| Connected devices:
1 x HP E243i Monitor @ 25W/h (typical)| Connected devices:
1 x HP E243i Monitor @ 25W/h (typical)
lx THD100 @ 60W/h (Typical)| lx THD100 @ 60W/h (Typical)| lx THD100 @ 60W/h (Typical)
1 x Dell XPS Laptop| 1 x Dell XPS Laptop| 1 x Dell XPS Laptop
1 x Sit to Stand Desk| 1 x Sit to Stand Desk| 1 x Sit to Stand Desk
Total Power draw (Typical)= 85W/h| Total Power draw (Typical)= 85W/h| Total Power draw (Typical)= 85W/h
Run time (Typical) calculated 206Wh/85Wh = 2 hours, 25min approx.| Run time (Typical) calculated 412Wh/85Wh = 4 hours, 50min approx.| Run time (Typical) calculated 618Wh/85Wh = 7 hours, 16min* approx.

FR210DS Wiring Example: Mobile Stand

Connected devices:
1 x Samsung QE50T @ 91W/h (typical), 149W/h (Max)
lx Logitech Meetup @ 18W/h
Total Power draw (Typical)= 109W/h
Total Power Draw (Max) = 167W/h| Connected devices:
1 x Samsung QE5OT @ 91W/h (typical), 149W/h (Max)
lx Logitech Meetup @ 18W/h
Total Power draw (Typical)= 109W/h
Total Power Draw (Max) = 167W/h| Connected devices:
1 x Samsung QE50T @ 91W/h (typical), 149W/h (Max)
lx Logitech Meetup @ 18W/h
Total Power draw (Typical)= 109W/h
Total Power Draw (Max) = 167W/h
Run time (Typical) 206Wh/109Wh = 1 hour, 52min approx.| Run time (Typical) 412Wh/109Wh = 3 hours, 46min approx.| Run time (Typical) 618Wh/109Wh = 5 hours, 39min approx.
Run time (Max)
206Wh/167Wh = 1 hour, 13min approx.| Run time (Max)
412Wh/167Wh = 2 hour, 27min approx.| Run time (Max)
618Wh/167Wh = 3 hours, 42min approx.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>