DECKED RC836 Tool Box Core Trax

Product Information

TOOL BOXCORE TRAX

The TOOL BOXCORE TRAX is a mounting system designed to secure Core Trax to the bedrails of a vehicle. It is made of high-quality aluminum and is durable enough to withstand heavy loads. The Core Trax is used to secure loads, such as tools, equipment, and other items, to the bed of a vehicle. The TOOL BOXCORE TRAX is easy to install and comes with all the necessary hardware.

Product Usage Instructions

HOWTO: TOOL BOXSCORE TRAX INSTALL

WARNING: The TOOLBOX must be securely fastened to the bedrails at all times.

Tools Needed

• Drill
• 5/32 drill bit
• Drill stop or piece of tape
• Screwdriver

CAUTION: You’ll most likely strip out the screws if you use a #2 screwdriver. Bad.

Step 1

Find a friend or bribe your kid to help you align the two Core Trax along the aluminum spanner just below the Tool Box lid.

Note: The mounting holes which are further inbound from the edge of the Core Trax (holes are 1 from the edge) should be located in the middle of the spanner and butt up next to each other. Center the coupled Core Trax in the middle of the aluminum spanner from left to right and top to bottom.

Step 2

Using the edge of one track, mark the centerline with a Sharpie or marking pen.

Step 3

Using the centerline made in Step 2, hold one Core Trax in
place. Use a 5/32 drill bit and a drill stop or piece of tape
placed at 1/2 to drill a pilot in the mounting location closest to
the center mark into the aluminum spanner.

Step 4

Install one screw and tighten until snug. Verify that the track is level and repeat with the remaining mounting holes using the Core Trax as a template.

Step 5:

Place and install the other Core Trax, making sure the tracks meet at the center. Use the included load locks to secure any loads (instructions are in the load lock package). Additional load locks are available for purchase at www.DECKED.com.
For more information, watch installation videos at www.DECKED.com/video or contact DECKED.COM at 208.806.0251.
RC836  V1 ATB4 @DECKEDUSA #DECKEDUSA

WARNING: TOOL BOX MUST BE SECURELY FASTENED TO THE BEDRAILS AT ALL TIMES. CHECK THE MOUNTING HARDWARE OFTEN TO CONFIRM IT’S TIGHT.

TOOLS NEEDED

• DRILL
• 5/32″ DRILL BIT
• 1/2″ DRILL STOP OR TAPE

• 3 PHILLIPS SCREWDRIVER

• (CAUTION: YOU’LL MOST LIKELY STRIP OUT THE SCREWS IF YOU USE A #2 SCREWDRIVER. BAD.)

STEP 1 :

• Find a friend or bribe your kid to help you align the two Core Trax along the aluminum spanner just below the Tool Box lid.
• NOTE: The mounting holes which are further inbound from the edge of the Core Trax (holes are 1″ from the edge) should be located in the middle of the spanner and butt up next to each other.Center the coupled Core Trax in the middle of the aluminum spanner from left to right and top to bottom.

STEP 2:

• Using the edge of one track, mark the centerline with a Sharpie or marking pen.

STEP 3:

• Using the centerline made in Step 2, hold one Core Trax in place.
• Use a 5/32″ drill bit and a drill stop or piece of tape placed at 1/2″ to drill a pilot in the mounting location closest to the center mark into the aluminum spanner.

STEP 4:

• Install one screw and tighten until snug.
• Verify that the track is level and repeat with the remaining mounting holes using the Core Trax as a template.

STEP 5:

• Place and install the other Core Trax, making sure the tracks meet at the center.
• Use the included load locks to secure any loads(instructions are in the load lock package).
• Additional load locks are available for purchase at www.DECKED.com.
• THESE MIGHT BE USEFUL: Watch installation videos at www.DECKED.com/video
• DECKED.COM 208.806.0251

References

• DECKED Truck Bed Storage, Tool Boxes & Truck Accessories
• DECKED Truck Bed Storage, Tool Boxes & Truck Accessories
• Truck Bed Storage and Organizer Videos from Decked

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>