FS S3700-24T4F Switch Full Gigabit Access Switch User Guide

: June 10, 2024
: FS

Table of Contents

Introduction
Accessories
Hardware Overview
Site Environment
Installing
Conﬁguring the Switch
Troubleshooting
Product Warranty
Compliance Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

S3700-24T4F Switch Full Gigabit Access Switch
User Guide

FS S3700 24T4F Switch Full Gigabit Access Switch

S3700-24T4F Switch
FULL- GIGABIT ACCESS SWITCH V3.1
Quick Start Guide

Introduction

Thank you for choosing FS S3700-24T4F Full-gigabit Access Switch. This guide is designed to familiarize you with the layout of the switch and describes how to deploy the switch in your network. FS S3700 24T4F Switch Full Gigabit
Access Switch - fig

Accessories

FS S3700 24T4F Switch Full Gigabit Access Switch -
Accessories

Hardware Overview

Front Panel Ports

FS S3700 24T4F Switch Full Gigabit Access Switch - Panel
Ports

Ports	Description
RJ45	10/100/1000BASE-T ports for Ethernet connection
SFP	Hot swappable SFP ports for 1G ﬁber connection
Console	An RJ45 console port for serial management

Front Panel Button

Button	Description
Reset	Keep the device powered on, press the button “RESET” for 6 seconds, and

the system will return to the default setting.

Front Panel LEDs

FS S3700 24T4F Switch Full Gigabit Access Switch - Panel
LEDs

LEDs	Status	Description
PWR	Green	Switch is powered on.
SYS	Blinking Green	System is working properly.
RJ45	Orange	10/100M connection.
Green	1000M connection.
Oﬀ	No signal transmission.
SFP	Green	1000M connection.
Oﬀ	No signal transmission.

Back Panel FS S3700 24T4F Switch Full Gigabit Access Switch - Back
Panel

Site Environment

Do not operate it in an area that exceeds an ambient temperature of 50°C.
The installation site must be well ventilated. Ensure that there is adequate air ﬂow around the switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.

Installing

FS S3700 24T4F Switch Full Gigabit Access Switch - Desk
Mounting

Attach four rubber pads to the bottom.
Place the chassis on a desk.

FS S3700 24T4F Switch Full Gigabit Access Switch - Rack
Mounting

Secure the mounting brackets to the two sides of the switch with eight M3 screws.
Attach the switch to the rack using four M6 screws and cage nuts.

Grounding the Switch

FS S3700 24T4F Switch Full Gigabit Access Switch -
Grounding

Connect one end of the grounding cable to a proper earth ground, such as the rack in which the switch is mounted.
Secure the grounding lug to the grounding point on the switch back panel with the washers and screws.
CAUTION: The earth connection must not be removed unless all supply connections have been disconnected.

Connecting to the power

FS S3700 24T4F Switch Full Gigabit Access Switch -
power

Plug the AC power cord into the power port on the back of the switch.
Connect the other end of the power cord to an AC power source.
WARNING: Do not install power cables while the power is on.

Connecting to the RJ45 Ports

FS S3700 24T4F Switch Full Gigabit Access Switch - RJ45
Ports

Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other network devices.
Connect the other end of the Ethernet cable to the RJ45 port of the switch.

Connecting to the SFP Ports FS S3700 24T4F Switch Full Gigabit Access
Switch - SFP Ports

Plug the compatible SFP transceiver into the SFP port.
Connect a ﬁber optic cable to the ﬁber transceivers. Then connect the other end of the cable to another ﬁber device.

Connecting to the Console Port

FS S3700 24T4F Switch Full Gigabit Access Switch - Console
Port

Connect the DB9 female connector of the console cable to RS-232 serial port on the computer.
Insert the RJ45 connector into the RJ45 console port on the front of the switch.

Conﬁguring the Switch

Conﬁguring the Switch Using the Web-based interface
Step 1: Connect your computer to any Ethernet port of the switch using the network cable.
Step 2: Set up the lap conﬁguration on your computer. The lap address of your computer should be set in the same subnet addresses of the switch.The lap address is 192.168.1.x(“x” is any number from 2 to 254).
Step 3: Open a web browser window. Enter the default lP address of the switch http://192.168.1.1 in the address bar and press Enter.
Step 4: When the login page appears choose the language that you prefer and enter the username and password.
The default username is admin. The default password is admin.
Step 5: Click Sign in to display the web-based conﬁguration page.

Conﬁguring the Switch Using the Console Port
Step 1:Connect a computer to the switch’s console port using the supplied console cable.
Step 2:Start the terminal simulation software such as HyperTerminal on the computer.
Step 3:Conﬁgure the terminal simulation with the following parameters:

115200 bits per second
8 data bits
no parity
1 stop bit
no ﬂow control

Step 4:Enter the username and password. The default username is admin. The default password is admin.

Troubleshooting

Power LED Working Abnormally

Check the power cable connections at the switch and the power source.
Make sure the power cord used matches the voltage and frequency of your local power.

HyperTerminal Displaying Abnormally

Make sure the power supply is normal and the console cable is properly connected.
Check if the console cable is the right type.
Check if the control cable driver is properly installed on the computer.
Ensure the parameters of the HyperTerminal are correct.

Accessing the Web-based Conﬁguration Page Unsuccessfully

Check every port LED on the switch and make sure the Ethernet cable is connected properly.
Try another port on the switch and make sure the Ethernet cable is suitable and works normally.
Power oﬀ the switch. After a while, power it on again.
Make sure the IP address of your PC is set within the subnet of the switch.
If you still cannot access the conﬁguration page, please restore the switch to its factory defaults.

Then the IP address of your PC should be set as 192.168.1.x (“x” is any number from 2 to 254) and Subnet Mask as 255.255.255.0.

Online Resources

Download https://www.fs.com/products_support.html
Help Center https://www.fs.com/service/fs_support.html
Contact Us https://www.fs.com/contact_us.html

Product Warranty

FS ensures our customers that any damage or faulty items due to our workmanship, we will oﬀer a free return within 30 Days from the day you receive your goods. This excludes any custom made items or tailored solutions.
Warranty: FS S3700-24T4F Switch enjoys 4 years limited warranty against defect in materials or workmanship. For more details about warranty, please check at https://www.fs.com/policies/warranty.html
**** Return: If you want to return item(s), information on how to return can be found at https://www.fs.com/policies/day_return_policy.html

Compliance Information

FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee hat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:
Any changes or modiﬁcations not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
Responsible party (only for FCC matter)
FS.COM Inc.
380 CenterPoint Blvd, New Castle, DE 19720, United States https://www.fs.com

FS.COM GmbH hereby declares that this device is in compliance with the Directive 2014/30/EU and 2014/35/EU. A copy of the EU Declaration of Conformity is available at www.fs.com/company/quality_control.html

FS.COM LIMITED
24F, Infor Center, No.19, Haitian 2nd Rd,
Beihai Community, Yehia Street, Nanshan
District, Shenzhen City
FS.COM GmbH
NOVA Gewerbepark Building 7, Am
Gild 7, 85375 Neufahrn bee Munich, Germany