Shuttle XH510G2 Unveils XPC Barebone Desktop User Guide

: June 4, 2024
: Shuttle

Table of Contents

Shuttle XH510G2 Unveils XPC Barebone Desktop
Product Overview
Hardware Installation
Safety Information
Motherboard Illustration
Jumper Settings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shuttle XH510G2 Unveils XPC Barebone Desktop

More information on this product can be found at: https://bit.ly/XH510G2

Product Overview

USB 2.0 Ports
USB 3.2 Gen1 Type-A Ports
MIC-in
Headphones
Power switch / Power LED
Hard disk drive LED
COM port (optional)
HDMI 2.0 Port
DisplayPort
LAN Port
Power Jack (DC IN)
Clear CMOS & Power Button & +5V
Perforation for optional WLAN (optional)
PCIe x16 slot
PCIe x1 slot
Kensington® Lock hole

Hardware Installation

A. HDD/SSD and USB Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

Turn your XH510G2 upside down,then unscrew one screw of the HDD/SSD cover and remove it.
Mount the HDD/SSD into the bracket with three screws.
Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD/SSD cable. Install the M.2 SSD, if required (refer step D).
Replace the HDD/SSD cover and refasten the screw.

B. CPU and ICE Module Installation

Unscrew these two thumbscrews of the chassis cover, slide the cover backwards and upwards. Then remove the EPE protective foam from the top of the thermal fins.
Unfasten the four ICE module attachment screws and unplug the fan connector. Remove the ICE module from the chassis and put it aside.
Follow the steps below to correctly install the CPU into the motherboard CPU socket.
This CPU socket is fragile and can easily be damaged. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage of the CPU.
Unlock and raise the socket lever.
Lift the metal load plate off the CPU socket.
DO NOT touch the socket contacts. To protect the CPU socket, always use the protective socket covver when the CPU is not installed.
Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.
Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU!
Tear off the protective membrane from the metal load plate.
Close the metal load plate, lower the CPU socket lever and lock in place.
Spread thermal paste evenly on the CPU surface.
Please do not apply excess amount of thermal paste.
Screw the ICE module to the motherboard. Note to press down on the opposite diagonal corner while tightening each screw.
Connect the fan.

C. Memory Module Installation

This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.

Locate the SO-DIMM slots on the motherboard.
Align the notch of the memory module with the one of the relevant memory slot.
Gently insert the module into the slot in a 45-degree angle.
Carefully push down the memory module until it snaps into the locking mechanism.
Repeat the above steps to install an additional memory module, if required.

D. M.2 Device Installation

Locate the M.2 key slots on the motherboard.
M.2 2242/2260/2280 M key slot
M.2 2230 E Key slot
Install the M.2 device into the M.2 slot and secure with the screw.
M.2 2242/2260/2280 M key slot
M.2 2230 E Key slot

E. How to change the battery

Use a flat-blade screwdriver to gently pry the metal tab to disengage the battery from the battery holder.
Install the new battery, press it on the battery holder keeping the positive side facing top.

F. Installation of Expansion Card

Unfasten the expansion slot bracket screw.
Remove the back panel bracket and put it aside.
The maximum permitted size for display cards is 208.5 mm x 120 mm x 45 mm.
The display cards must be installed on the riser card, not on the motherboard.
Install the PCIe x1 / PCIe x16 card into the PCIe x1 / PCIe x16 slots.

G. Complete

Replace the cover and tighten the thumbscrews, then connect the power cord.
Complete.

Please press the “Del” key while booting to enter BIOS. Here, please load the optimised BIOS settings.

H. Installation of VESA Mount

Follow the steps 1-2 to install the VESA mount.

Supports 75×75 mm and 100×100 mm VESA standard.

Safety Information

Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer’s instructions.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Overview

USB 2.0 ports
USB 3.2 Gen1 Type-A Ports
MIC-in
Headphones
Power switch / Power LED
Hard disk drive LED
COM port (optional)
HDMI 2.0 Port
DisplayPort
LAN Port
Power Jack (DC IN)
Clear CMOS & Power button & +5V
Perforation for optional WLAN (optional)
PCIe x16 slot
PCIe x1 slot
Kensington® Lock hole

Motherboard Illustration

Power Jack (DC IN)
USB 2.0 Ports
USB 3.2 Gen1 Type-A Ports
LAN Port
DisplayPort
HDMI 2.0 Port
M.2 2230 E key slot
PCIe x16 slot
Processor socket LGA1200
M.2 2242/2260/2280 M key slot
Intel® H510 Chipset
CMOS battery holder
DDR4 SO-DIMM slots
5V Power Supply connector
M.2 2280 M key slot (SATA only)

Jumper Settings

Clear CMOS & power button & +5V
SW1

Pin| Signal Name| Pin| Signal Name
1| RTCRST-| 2| +5V
3| GND| 4| PWRSW-
Port \ COM
COM1 (RS232)

Pin| Signal Name| Pin| Signal Name
1| DCD| 2| RX
3| TX| 4| DTR
5| GND| 6| DSR
7| RTS| 8| CTS
9| RI| 10| NULL
VGA Connector
CN4

Pin| Signal Name| Pin| Signal Name
1| GND| 11| CRT_HSYNC
2| GND| 12| GND
3| VGA_SCL| 13| GND
4| GND| 14| GND
5| VGA_SDA| 15| BOUT-O
6| GND| 16| VGA_PWR
7| GND| 17| GOUT-O
8| GND| 18| VGA_PWR
9| CRT_VSYNC| 19| ROUT-O
10| GND| 20| VGA_PWR
Debug header
DBG1

Pin| Signal Name| Pin| Signal Name
1| EC_ESCK| 2| EC_EIO1
3| EC_PLRST_N| 4| EC_EIO0
5| ESPI_CS0#| 6| DEBUG_PWR
7| EC_EIO3| 8| GND
9| EC_EIO2| 10| NULL
11| ESPI_ALERT0#| 12| ESPI_RST#
Fan connector
FAN1

Pin| Signal Name
1| GND
2| +12V
3| SPEED_SENSE
4| PWM_CTRL
USB 2.0 cable connector \ USB 2.0
USB4

Pin| Signal Name
1| GND
2| USB_D+
3| USB_D-
4| USB_5V
Power header
SW1

Pin| Signal Name| Pin| Signal Name
1| HDLEDPWR| 2| SYSLEDPWR
3| SATA_LED| 4| GND
5| RST_SW| 6| PWR_SW
7| GND| 8| GND
9| NC| 10| NULL
USB connector \ USB
USB1

Pin| Signal Name| Pin| Signal Name
1| USB_PWR| 2| USB_PWR
3| USB3-| 4| USB4-
5| USB3+| 6| USB4+
7| GND| 8| GND
9| NULL| 10| GND
Front audio header
AUDIO1

Pin| Signal Name| Pin| Signal Name
1| MIC_L| 2| GND
3| MIC_R| 4| AUDIO_JD
5| HP_R| 6| MIC_JD
7| SENSE| 8| NULL
9| HP_L| 10| HP_JD
AC auto power-on
JP1

Pin| Signal Name
1| AMP+
2| GND
2.5” SATA cable connector
SATA1

Pin| Signal Name| Pin| Signal Name
1| NC| 11| +5V
2| NC| 12| GND
3| NC| 13| GND
4| NC| 14| GND
5| GND| 15| SATA_TX+
6| GND| 16| SATA_TX-
7| GND| 17| GND
8| +5V| 18| SATA_RX-
9| +5V| 19| SATA_RX+
10| +5V| 20| GND
Front USB 3.0 header
USB5

Pin| Signal Name| Pin| Signal Name| Pin| Signal Name
1| +3.3VS| 11| U3_TX1P| 21| U3_TX0N
2| +5VS| 12| GND| 22| GND
3| +5VS| 13| USB2_N| 23| U3_RX0P
4| +5VS| 14| USB2_P| 24| U3_RX0N
5| PWR_USB#| 15| GND| 25| GND
6| GND| 16| GND| 26| PWR_USB#
7| U3_RX1N| 17| USB1_P| 27| +5VS
8| U3_RX1P| 18| USB1_N| 28| +5VS
9| GND| 19| GND| 29| +5VS
10| U3_TX1N| 20| U3_TX0P| 30| +3.3VS