BOSCH BDS Series Display Mount Instruction Manual
- June 10, 2024
- Bosch
Table of Contents
BDS Series Display Mount
Instruction Manual
BDS3210/BDS3250/BDS3620/BDS3630
Safety instructions
Read all the safety information and instructions. Failure to observe the
safety information and follow instructions may result in electric shock, fire
and/or serious injury.
Save all safety warnings and instructions for future reference.
- The contact surfaces of the display holder may become very hot (> 60 °C). Allow the contact surfaces toadjust to the ambient temperature before you touch them. This is particularly important when using a SmartphoneGrip.
- Keep swallowable small parts away from small children. There is a risk of serious injury.
- Never short-circuit the pins. The display holder may be irreparably damaged and must then be replaced.
- Ensure that the contacts are free of dirt. By doing this, you prevent malfunctions or damage.
- After a fall, check the display holder for sharp edges. Replace it if required.
- Do not stand your bicycle upside down on its saddle and handlebars if the on-board computer or its holder protrude from the handlebars. This may irreparably damage the on-board computer or the holder. Also remove the on-board computer before placing the bicycle on a wall mount to ensure that the on-board computer does not fall off or become damaged.
- Observe all national regulations which set out the approved use of eBikes.
- Read and observe the safety warnings and directions contained in all the eBike system operating instructions and in the operating instructions of your eBike.
Product description and specifications
Intended use
The display holder is intended to establish the mechanical and electrical
connection to a display or on-board computer. Only original Bosch eBike
components can be connected to the display holder.
A display holder is not required for an eBike system to function.
Product features
The numbering of the components shown refers to the illustrations on the
graphics pages at the beginning of the manual.
- Display mount
- Adapter tray
- Clamp for holder
- Clamp screw
- Round rubber spacer
- 1-arm socket
- Screw for adjusting tilt
- Removal blocker
- Snap-in hook
- Connection cables
- Fastening screws for display mount
The display mount (1) can also be embedded in the bicycle design.
Technical data
Display holder| |
---|---|---
Product code| | BDS3210
BDS3250
BDS3620
BDS3630
Output voltage| V| 4.75 to 5.4
Output current, max.| A| 1.5
Operating temperature| °C| –5 to +40
Storage temperature| °C| +10 to +40
Protection rating| | IP54
Fitting
Installation positions
The 1-arm socket can be mounted at three different positions on the
handlebars:
– In front of the handlebars ➀
– Over the stem ➁
– In the triangle between the stem and handlebar ➂
Note: In order to ensure clean cable routing, the appropriatedisplay
mount must be used for each of the three different positions: The BDS3210
display mount for in front of the handlebars (electrical connections at the
rear); the BDS3250 display mount for over the stem or in the triangle between
the stem and handlebar (electrical connections at
the front).
If you want to change the installation position and you have the correct
display mount (1), you must first remove the 1arm socket (6) and re-mount it
afterwards.
Note: Please be aware that there are two different handlebar diameters
(31.8 mm and 35 mm). Your bicycle retailer will help you to select the correct
components.
Mounting the display mount
Insert the display mount (1) into the adapter tray (2). Ensure that
it is in the required installation position. Secure the display mount (1) from
below using the screws (11).
Whendoing so, be aware of the torque specified on the adapter tray (2).
Connect the connection cables that come out of the drive unit and the control
unit. It does not matter which cable is connected to which connection for the
functions to work. When connecting the cables, ensure that the markings on the
connector and on the cable match.
Securing on the handlebars
Note: The display holder must only be secured in the cylindrical area of the
handlebars and not in the tapered area.
To clamp a display in the centre, the handlebars must have a cylindrical area
of at least 90 mm in width. Open the clamp and bring the 1-arm socket (6),
together with the round rubber spacer (5), into the required position. Gently
tighten the clamp screw (4) so that the 1-arm socket (6) can still move.
Adjust the tilt for the display mount by loosening and tightening the screw
(7). Preferably adjust the tilt without the display or on-board computer.
In the connection between the 1-arm socket (6) and the adapter tray, there are
interlocking teeth, which means that it is only possible to align the adapter
tray in predefined
positions. Before tightening the screw (7), make sure that the teeth engage in
one another correctly. In addition, be aware of the torque specified on the
1-arm socket (6).
Bring the 1-arm socket (6) into its final position and tighten the clamp screw
(4). Be aware of the torque specified on the 1-arm socket (6) here too.
Thanks to the round rubber spacer (5), it is possible to move the 1-arm socket
(6) in all directions.
Removal blocker
A device attached to the display holder can be secured using the removal
blocker (8). Usage is described in the operating instructions for the
respective device.
Maintenance and servicing
Maintenance and cleaning
The display holder must not be cleaned with pressurised water.
Use a soft cloth dampened only with water for cleaning.
Do not use cleaning products of any kind.
After-sales service and advice on using products
If you have any questions about the eBike system and its components, contact
an authorised bicycle dealer.
For contact details of authorised bike dealerships, please visit www.bosch-
ebike.com.
Disposal
The drive unit, on-board computer incl. operating unit, battery, speed sensor,
accessories and packaging should be disposed of in an environmentally correct
manner.
Do not dispose of eBikes and their components with household waste.
**** In accordance with Directive 2012/19/EU and Directive 2006/66/EC
respectively, electronic devices that are no longer usable and
defective/drained batteries must be
collected separately and recycled in an environmentally friendly manner.
Please return Bosch eBike components that are no longer usable to an
authorised bicycle dealer.
Subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>