ANCEL BZ700 Mercedes Benz Multi System Scanner User Manual

June 10, 2024
ANCEL

USER’S MANUAL
B2700ANCEL BZ700 Mercedes Benz Multi System
Scanner

Safety Precautions and Warnings

To avoid injury or damage to the vehicle and/or scan tool, first read this manual and observe the following safety precautions when working on a vehicle:

  • First, turn off the ignition. Connect the 16-pin connector, and then turn on the ignition. Always perform vehicle tests in a safe environ­ ment.
  • Do not attempt to operate or observe the device while driving a vehicle.
  • Operating or observing the device distracts the driver and may result in a fatal accident.
  • Wear safety glasses that meet the standards of ANSI.
  • Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated area: exhaust fumes are toxic.
  • Place blocks in front of the drive wheels and never leave the vehicle unattended while performing tests.
  • Use extreme caution when working near the ignition coil, distributor cap, ignition wires and spark plugs. These components generate dangerous voltages when the engine is running.
  • Keep a fire extinguisher nearby that is suitable for gasoline, chemical, and electrical fires.
  • Keep the scan tool dry, clean, and free of oil/water or grease. If necessary, use a mild detergent on a clean cloth to clean the outside of the scan tool.

Instructions Manual

  1. Turn on the vehicle ignition;
  2. Locate the vehicle’s 16-pin Data Link Connector (DLC);
  3. Connect the device to the vehicle’s 16-pin Data Link Connector, do not use USB to power devices;
  4. Start using your device.

Product Descriptions

  1. BZ700 works on most after1996 OBDI I compliant US, European and Asian vehicles.
  2. Mercedes-Benz cars (including Maybach), (1991-2021 ).
    Mercedes-Benz Sprinter (commercial vehicle series, some of these models have a 38PIN diagnostic interface, which is not supported). Benz Smart (Smart).

Product Specification
2.8’LCD,320 X 240 pixels color screen
Operating Voltage: 8V-18V
Operating Temperature: 0°C-60°C(32-140°F)
Storage Temperature: -20°C-?0°C(4-158°F)

Description of appearance and buttonsANCEL BZ700 Mercedes Benz Multi
System Scanner - Description

  1. LCD DISPLAY – Displays test results. Display with backlight, 320 x 240 pixels
  2. [OK] BUTTON – Confirms a selection (or action) from a menu.
  3. [ESC] BUTTON – Cancels a selection (or action) from a menu or returns to the menu.
  4. [LEFT] SCROLL BUTTON – move left through menu and submenu in menu mode, when scrolling in a data interface the left key can be used to move to the last screen.
  5. [RIGHT] SCROLL BUTTON – in menu mode move through the menu and submenu items to the right, when scrolling in a data interface the right key can be used to move to the next  screen.
  6. [UP] SCROLL BUTTON – in menu mode, move up through the menu and submenu items. When retrieving data for more than one screen, by moving the screen up to the previous screen  for more data.
  7. [DOWN] SCROLL BUTTON – in menu mode, using the menu and submenu items to move down. If retrieving data for more than one screen, move down the screen to the next screen for  more data.
  8. OBD-16PIN CONNECTOR- Connects the scan tool to the vehicle’s Data Link Connector (DLC).
  9. [1/M] BUTTON – Quick State Emissions Readiness Check and Drive Cycle Check.
  10. [READ OTC] BUTTON – Quick readout of the vehicle’s fault code.

ANCEL BZ700 Mercedes Benz Multi System Scanner -
remark

Diagnosis

4.1 For Benz
This product mainly tests Mercedes-Benz, Sprinter and Smart.
Let’s take Mercedes-Benz as an example to analyze the general functions of the product.
Select [For Benz] it will show as follows: ANCEL BZ700 Mercedes Benz Multi
System Scanner - Figure 1

4.1.1 Select [OK] to continue, In [For Benz Diagnose], Select [Last Test Record] and the following interface will appear: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 2

Remark: In the last test record, you can quickly find the result of the last test.
4.1.2 In [Automatically Search], it can identify the name and year of the vehicle by VIN. ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
3

Mark: [Automatically Search] read VIN to analyze and identify specific models and chassis. Currently, only Mercedes-Benz cars support automatic recognition, and Smart and Sprinter do not support Automatically Search.
4.1.3 Manually Select: If the automatically Search is abnormal, customer can use the Manually Select to test.
In [Manually Select], it shows as follows: ANCEL BZ700 Mercedes Benz Multi
System Scanner - Figure 4ANCEL BZ700
Mercedes Benz Multi System Scanner - Figure 5

Select [Health Report],it shows as follows: ANCEL BZ700 Mercedes Benz Multi
System Scanner - Figure 6

Select [Control Units], it display as belows:

ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
7

Select [Version lnformation],it display as belows:

ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
9

Select [Read Fault Codes], it will show as follows:ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 10

Select [Erase Fault Codes], it display as belows: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 11

Select [Read Data stream], it display as follows: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 12ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
13

Mark: Select [LEFT] and [RIGHT] buttons to page
Select [UP] and [DOWN] buttons to select one by one
Select [OK] button to select the Datastream
Select [ESC] button to read Datastream
Select [Special Functions],it will display as follows: ANCEL BZ700 Mercedes
Benz Multi System Scanner - Figure 14

Note: The special functions supported by different models are different
4.2 Special Functions for Benz
2.2.1 Oil Service Light Reset
Select [Special Functions] and go to [Oil Service Light Reset] Follow the instructions on the interface to complete the Oil Service
Light Reset. The specific steps are as follows: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 15ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
16ANCEL BZ700 Mercedes Benz Multi System
Scanner - Figure 17

Note: The above is the main content of Oil Service Light Reset; please operate according to the above steps.

4.2.2 EPB Replace Brake Pads
Select [Special Functions]and go to [EPB Replace Brake Pads] Follow the instructions on the interface to complete the EPB
Replace Brake Pads. The specific steps are shown in the figure below. ANCEL
BZ700 Mercedes Benz Multi System Scanner - Figure 18ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
19ANCEL BZ700 Mercedes Benz Multi System
Scanner - Figure 20

Note: The special features of each model are different, please according to the actual operation.

OBDII System

5.1 Read Codes
Select [OBDII] and select [Read Codes], it will be displayed as follows: ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
21

5.2 Erase Codes
Select [0B011] and select [Erase Codes], it will be displayed as follows: ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
22

A warning message comes up asking for your confirmation.

Press the [OK] button to confirm. ANCEL BZ700 Mercedes Benz Multi System
Scanner - Figure 24

5.3 1/M Readiness
Select [OBDII] and select [1/M Readiness], it will be displayed as follows: ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
25

5.4 Data Stream
Select [OBDII] and select [Data Stream], it will be displayed as follows:

ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
26

5.5 Evap System Test
Select [OBDII] and select [EVAP System Test], it will be displayed as follows: ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
27

5.6 Vehicle Information
Select [OBDII] and select [Vehicle Information], it will be displayed as follows:

ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
28

BAT Check

This function allows you to read the battery voltage in real time.
From the main menu, use the navigation button LEFT/ RIGHT to select the menu BAT and press the button OK. The screen will display the interface shown below:ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
30

Please turn off the engine.

When you press [OK] and start the detection, the interface will be displayed:

Tool Setup

7.1 Language
Select [Language] and it displays as follows: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 33

7.2 Beeper
Select [Beeper] and it displays as follows:ANCEL BZ700 Mercedes Benz Multi
System Scanner - Figure 34

7.3 Instructions (Display at startup)
Select [Instructions (Display at startup)] and it displays as follows: ANCEL
BZ700 Mercedes Benz Multi System Scanner - Figure 35

7.4 Unit of measure
Select [Unit of measure] and it displays as follows: ANCEL BZ700 Mercedes
Benz Multi System Scanner - Figure 36

7 .5 Skin Style
Select [Skin Style] and it displays as follows: ANCEL BZ700 Mercedes Benz
Multi System Scanner - Figure 37

7 .6 Feedback

  1. If the device indicates a connection error with the vehicle or any other problem, during use, please use the feedback function.
    Select [Feedback] and it will be displayed as follows:
    ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
38or Example:Register Battery Change enter [Register Battery Change] and run Register Battery Change again (This step is very important).
    Note: Keep the device connected to the vehicle during the above steps.

  2. After you have registered the battery change, disconnect the device from the vehicle.

  3. Transfer the data to your computer and create a feedback file. (You need to download the update file from ANCEL website to your computer).
    The device is connected to the computer via USB cable.
    ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
39

Select the “Update” file and it will be displayed as follows:

ANCEL BZ700 Mercedes Benz Multi System Scanner - Figure
40

Click “Feedback” and it displays as follow: ANCEL BZ700 Mercedes Benz Multi
System Scanner - Figure 41

Please send the feedback.bin file to support@anceltech.com ANCEL BZ700 Mercedes Benz Multi System
Scanner - Figure 42

7. 7 Device information
Select [Device information] and it will be displayed as follows:ANCEL BZ700
Mercedes Benz Multi System Scanner - Figure 43

Update

  1. Download the update software and unzip the file.
  2. Connect the device to the computer via USB cable.
  3. The update software is only supported by 7/8/10. In Windows 7, you need to install the driver, in Windows 8/10, you can run the update software directly.

Note:
Windows XP and Apple computers do not support upgrades.
If you do not understand the upgrade steps in the instructions, please contact ANCEL customer service.

Warranty

  1. This warranty is limited to the person who purchases ANCEL products.
  2. ANCEL products are warranted against defects in materials and workmanship for a period of one year (12 months) from the date of shipment to the user.

OBDSPACE TECHNOLOGY CO.,LTD
Address: Runfeng office longhua district Shenzhen Guang Dong
518000 P.R. China.
support@anceltech.com
www.anceltech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals