Honeywell R110 Cloud Link Cat M1 Modem User Manual

CloudLink Cat M1 Modem
R110
Software Change Notice
Revision Date: April 7, 2022
Document ID: Software Change Notice

Notices and Trademarks

© Honeywell International Inc. 2012. All Rights Reserved.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a particular  purpose and makes no express warranties except as may be stated in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change  without notice.
Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions
1250 W Sam Houston Pkwy S
Houston, Tx 77042 USA
www.honeywellprocess.com

Symbol Definitions

The following table lists those symbols used in this document to denote certain conditions.

task.
| REFERENCE -EXTERNAL: Identifies an additional source of information outside of the booklet.
| REFERENCE – INTERNAL: Identifies an additional source of information within the booklet.
CAUTION| Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being damaged or lost, or may result in the inability to properly operate the process.
| CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.
CAUTION symbol on the equipment refers the user to the product manual for additional information. The symbol appears next to required information in the manual.
| WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in serious injury or death.
WARNING symbol on the equipment refers the user to the product  manual for additional information. The symbol appears next to
required information in the manual.
| WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 Peak, or 60 VDC may be accessible.
| ESD HAZARD: Danger of an electro-static discharge to which equipment may be sensitive. Observe precautions for handling electrostatic sensitive devices.
| Protective Earth (PE) terminal: Provided for connection of the protective earth (green or green/yellow) supply system conductor.
| Functional earth terminal: Used for non-safety purposes such as noise immunity improvement. NOTE: This connection shall be bonded  to Protective Earth at the source of supply in accordance with national local electrical code requirements.
| Earth Ground: Functional earth connection. NOTE: This connection shall be bonded to Protective Earth at the source of supply in  accordance with national and local electrical code requirements.
| Chassis Ground: Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements.

Introduction

1.1 About CloudLink Cat M1 Modem
Cloud Link is a future proof intrinsically safe cellular radio (Cloud Link) with form factor, certifications and carrier approvals that can also be used as a component in a variety  of industrial process control and monitoring applications and wireless platforms. Cloud Link can be used with wireless applications with cellular and BLE.

1.2 About this Document
The Cloud Link R110 Release Notes is intended for service engineers who are assigned to provision, configure, operate Cloud Link Cat M1 device

1.3 Limitations
N/A

1.4 Technical Assistance
Honeywell PMC
2101 City West Blvd,
Houston, TX 77042
Telephone: 855-251-7065
Email: MI-TAC-Support@Honeywell.com
Website: https://www.honeywell.com/ps

Contents of Release

Cloud Link R110 Firmware version is v1.02.12
Table 1 Cloud Link Cat M1 Modem

Release Overview

3.1 Features
Key features of Cloud Link are mentioned below:

1. Cellular Communication
   Supported Bands:
   i. LTE(CatM1) : Band 13.

2. Supports IPv4 Internet Protocols

3. Call in / Call out
   • CloudLink Supports Call in (CloudLink device connects to the host system (Power Spring) over IPv4 through LTE(CatM1).
   • CloudLink Supports Call Out (CloudLink listens for connections from the host system (Master Link / Power Spring) over IPv4 through LTE(CatM1).

4. Bluetooth Low Energy (BLE) communication
   • Bluetooth Low Energy Communication is short range wireless communication used for communicating with Mobile devices, Mobile Tabs

5. Serial Communication
   • RS232 Interface
   • RS485 Interface

6. Firmware upgrade
   • CloudLink device firmware can be upgraded remotely using Cellular Interface (Over The Air) by host software (Master Link/CloudLink Connect)
   • CloudLink firmware upgrade can also be done using RS232, RS485, BLE interfaces in the field.

7. Pulse Counting
   a. CloudLink Supports one pulse input, these pulse count can be read remotely by sending AT commands over serial interface

8. Diagnostics Support
   • CloudLink device has 4 LEDs used for various diagnostic indication
   • CloudLink device logs diagnostic information can be read remotely over cellular interface

9. Cellular Statistics
   • CloudLink device logs each call data like Access Technology, RSSI, Location ID / TAC, Cell ID, Physical Cell ID, MCC, MNC, Last Call Duration, Last Call Status

10. AT commands
    • Custom commands provided to read Cloud Link Diagnostic and pulse count information

11. Alarms
    • CloudLink generates alarms in case of Emergency call in (Magnetic switch call) and Low Battery Indication

12. Field / Remote Configuration
    • Device can be configured remotely or in the field

13. Password protected communication
    • Configuration Over Serial Interface, BLE, EC350 IR, Cellular Interface

14. Transparent modem
    • CloudLink will act as integrated transparent modem, or standalone modem

15. Security
    • Supports BLE Just Works and Passkey Entry
    • Whitelisting

3.2 New Features
This release contains the following new enhancements:
3.2.1 New alarms types added. Item i3189 provides the active alarms conditions.

• Radio Power ON Failure
• SIM Card Error
• Radio Registration Failure
• Radio Module Not Responding
• Data Connection Failure
• Host Not Reachable – Call Failure

3.2.2 Network drop recovery mechanism, new item number i3193 introduced for recovering from network drop (RGASMETER-284)

Disable

Note:

1. Recovery mechanism works based on principle of creating a network traffic from the unit to cellular network at defined time interval to avoid out-off network for longer duration.
2. This is achieved through the item number i3193. TCP server is closed periodically for the time mentioned in the item number i3193 and opens TCP client and gets connect to the IP address mentioned in item number i3042. By doing this, unit will try to connect to the IP address mentioned in i3042 which creates a network traffic from the unit to cellular network.
3. The default IP address in i3042 can be changed only if i3036 is ENABLE.

3.3 Changes to Existing Functionality
This release contains the following changes to existing functionality:

3.3.1 FOTA feature is improved in this build.
Refer to FOTA update Procedure from the FOTA update instructions

• To setup FTP server you can refer to our knowledge base article Setup FTP server with FileZilla.
• When FOTA is initiated, continuous server mode or call out window is closed and proceed with FOTA process. After FOTA process if continuous server mode is  enabled, continue with continuous server mode.
• Event logs are enhanced for FOTA in this build.
• New Radio FW version is updated in item number i3021 after FOTA.

Note:

1. To perform FOTA, firstly application FW must be upgrade with this build v1.02.12 using master link
2. Perform FOTA only if radio FW version in item number i3021 is other than 30.10.002-B003. This radio FW version is having a fix from radio vendor side for radio not responding and LED error code -12.

3.3.2 AT command response timing delay increased as suggested by Tallit radio vendor to prevent radio going into nonresponse state and need to upgrade radio FW version  to 30.10.002-B003 through FOTA as mentioned in above point 3.3.1 note – 2. (RGASMETER – 444).
3.3.3 Changed firmware upgrade item number i3107 behavior as explained below:

Disable 4 Firmware upgrade of the unit is not allowed.

Note: After firmware upgrade item number i3107 is automatically reverted to default state.
3.3.4 Error shown in master link for FW upgrade, changed from access code error (error code 27) to data write denied (error code – 39).
3.3.5 Fix call-in failure (from not flushing comma buffers from previous call) (RGASMETER 463)
3.3.6 Fix call-in failure (from premature cellular network registration timeout) (RGASMETER491)
3.3.7 Fix call-in failure (from premature IP packet time-out – call dropped and reported as Network Read/Write error in PS)
3.3.8 Fix call-in failure (from sending RG packets out of order – call dropped and reported as BAD CRC error in PS) (RGASMETER-476)
3.3.9 Fix to preserve item 3113 pulse count through soft reset operation
3.3.10 Fix BLE start/stop time functionality
3.3.11 Fix BLE pass-through to instrument disable (3162=0 was not blocking it as intended)
3.3.12 Fix duplicate cellular logs for same call
3.3.13 Fix call duration in cellular logs

3.4 Retired Features
The following features and functions have been removed from the release: N/A

Software/Hardware/Firmware Compatibility

Documentation Updates/Additional Information

N/A

Problems Resolved

This section provides an overview of the problems resolved in this release.

Installation and Migration

N/A

Un-Install Instructions

N/A

Issues

N/A

Security-Related Issues

N/A

Special Considerations

N/A

Third-Party Software Components

N/A

Appendix

N/A

Milestone Completion Checklist

Software Change Notices are directly related to a specific release. The criteria for assessing SCNs are not dependent on the phase.

Construction
For most HIP types, the draft SCN for the final release shall be available by end-of-construction and shall include content in all sections.
For the Express Delivery HIP type, which features only a Construction phase, the draft SCN needs to be complete as builds are turned over to Test, who then verifies the  work product as a part of the test efforts.

Phase in which Release Occurred
Process Compliance Checklist High Level Evaluation Criterion:

• Software Change Notice prepared & reviewed prior to gaining acceptance to Release.

All sections completed.
The hidden test within this document should be used when reviewing content.|
All sections completed.
The hidden test within this document should be used when reviewing content.| Check for evidence of review & that resulting  issues have been tracked-to- closure.

Cloud Link Cat M1 Modem Release R110
Software Change Notice

Documents / Resources

| Honeywell R110 Cloud Link Cat M1 Modem [pdf] User Manual
R110 Cloud Link Cat M1 Modem, R110, Cloud Link Cat M1 Modem, Cat M1 Modem, M1 Modem
---|---

References

• Home
• Article Detail
• Article Detail
• Honeywell Privacy Statement

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>